O-KAM Pro APP Download

O-KAM Pro supports Android and iPhone, you can download it from google play or app store.

Login O-KAM Pro

You need to register and login to O-KAM Pro APP to connect the camera, click Register now or email icon to register.

It is recommended to allow all permissions of the APP, otherwise you may not be able to use and connect the O-KAM Pro camera properly.

Connect O-KAM Pro Camera To Wifi

This connection mode supports O-KAM Pro wifi camera and battery camera.

1. Connect the O-KAM Pro Camera to a power source, and if it is a battery camera, press and hold the power button to start the camera.

2. Click + , then scan the QR code on the O-KAM Pro camera, the APP will automatically enter the appropriate connection mode.

If you can’t find the QR code or can’t scan the QR code, please select Wireless camera.

3. Make sure your O-KAM Pro camera is ready to connect, the camera light is flashing or you hear the prompt “Please use the app for Wi-Fi configuration”.

Note: If the light is not blinking or there is no prompt tone, please reset the camera.

Then click ‘I heard the prompt tone or see the indicator light flashing’, go to the next step.

4. Enter your wifi password, then click Next.

Please choose 2.4G wifi, some O-KAM Pro cameras only support 2.4G wifi.

.

See also  O-KAM Pro Camera FAQ and Troubleshooting

.

5. Make sure your wifi is 2.4g and the wifi password is correct, then click Confirm. Give the displayed QR code to the camera to scan.

Place the QR code about 15-30 Inch in front of the camera to scan, and complete the scan after hearing the “beep” sound.

After the connection is successful, it will automatically jump to the next step.

After successful connection, you can test the wifi signal strength, or later in the test, please put the O-KAM Pro camera in the location with strong wifi signal.

The app will prompt you to subscribe, it is recommended to cancel, if you need cloud storage, make sure the O-KAM Pro camera can work properly before subscribing.

AP Mode Connecting O-KAM Pro Camera

If the QR code connection fails or the QR code cannot be scanned, you can try to connect the O-KAM Pro camera using AP mode.

1. Go to your mobile phone’s wifi list to connect to the hotspot wifi of the O-KAM Pro camera, return to the O-KAM Pro APP after the connection is successful, and then the app will auto add the camera.

Below is the name of the O-KAM Pro camera’s hotspot wifi:

2. Go to Settings, select Device Settings, and then click Wi-Fi network.

3. Select your wifi, then enter your wifi password, click Confirm and wait for O-KAM Pro camera to connect to your wifi.

Share O-KAM Pro Camera

Once you have connected the O-KAM Pro camera, if you want your family or friends to use the camera as well, you need to share the camera with your friends via the Share function.

1. Go to the Share screen, then send the QR code to your friend.

Permission Settings:

.

See also  O-KAM Pro Camera FAQ and Troubleshooting

.

2. Have the invitee download the O-KAM Pro APP and register and login, then click + scan the QR code to add a camera.

Connecting O-KAM Pro Camera without a router

If you want to use O-KAM Pro camera without internet or router, you can connect to the included hotspot wifi to use the camera.

This mode only supports close range use.

1. Go to your mobile phone’s wifi list to connect to the camera’s hotspot wifi, after connecting, return to O-KAM Pro, the app will auto add the camera, then you can start to use it.

Below is the name of the O-KAM Pro camera’s hotspot wifi:

Function setup – Wired O-KAM Pro Cameras

The functions of different types of O-KAM Pro cameras differ slightly, so please check your camera type.

If your camcorder needs to be connected to the power supply at all times to work, then it is a wired O-KAM Pro camcorder type, please check the function setting instructions below.

Recording Setup – Wired O-KAM Pro Cameras

O-KAM Pro camera supports cloud storage and memory card recording, cloud storage requires subscription, the following memory card recording settings.

You need to insert the memory card to record, the recording will be saved in the memory card, after inserting the memory card, the camera will sound a voice prompt.

The default is to start 24 hours recording, you can change the recording mode in TF Record Settings.

O-KAM Pro camera supports the following recording modes:

If the memory card shows abnormality, please try to format the memory card and reboot the camcorder.

View Recordings – Wired O-KAM Pro Cameras

In the live video interface, click TF Card in the lower right corner to view the video saved in the memory card.

Motion Detection Setup

Activate the Motion Detection function in the Monitoring Function, O-KAM Pro cameras support Motion Detection and Human Detection.

Motion Detection

When the camera detects an object moving, it will send an alarm notification to your mobile phone.

This mode may have a high false alarm rate, if you need to detect only suspicious people, we recommend you to choose Human Detection.

Human Detection

The camera will send alarm notifications to your mobile phone only when it detects humanoid objects.

Activity Zone Setup

Setting the detection area allows the camera to detect a specific location, reducing the chance of false alarms.

Smear the area you don’t need.

Detection schedule

Customize the schedule of Motion detection, reduce false alarms. The camera automatically monitors for you during the scheduled time.

Alarm flashing light

After the alarm flashing light is turned on, the camera will automatically flash when motion detection is triggered.

Camera Siren

When Alarm sound switch is turned on, the camera will emit alarm sound when motion detection is triggered, you can choose alarm sound or record your own sound.

Enter Notification Settings, select Camera Siren and then turn on the Alarm sound switch.

Email notification

An email will be sent to you when a motion is detected.

Click Add an email , then enter the email address you want to receive alarm notification and finish the setting.

Auto Tracking

When Person tracking is activated, the camera will Auto Track people’s movements and monitor all activities. It will automatically switch to and focus on the person when they enter the camera’s field of vision.

This feature is only supported by O-KAM Pro cameras that support PTZ.

Human frame

People are automatically framed in the live video Help you filter out motions of other objects and quickly follow the person’s movement.

Night vision setup

O-KAM Pro camera defaults to black and white night vision mode, you can change the night vision mode in Device Settings, Night Vision.

Only cameras with dual light sources support this feature.

Reset O-KAM Pro Camera

Press and hold the O-KAM Pro camera reset button for 5 seconds to reset the camera.

.

O-KAM Pro Camera FAQ and Troubleshooting

You can find here how to fix O-KAM Pro camera can’t connect to wifi, offline and not working problems.

.

Why is my O-KAM Pro Camera offline?

O-KAM Pro camera is offline, it means the camera can’t connect to the network properly, please follow the steps below to fix the offline problem:

Is the router working properly?
Connect your mobile phone to the router Wi-Fi, switch off the mobile data, can you access the internet normally? If it is not normal, try to restart the router.

Whether the WiF strength is full or not
Put the mobile phone to the camera installation location, detect whether the Wi-Fi signal is full? If the signal is weak, it is recommended to adjust the distance from the router to the camera.

Whether the O-KAM Pro camera is normal
If a memory card is inserted into the O-KAM Pro camera, power off the camera and remove the memory card, then check if the camera works properly.

Replace the power supply with another one.

If none of the above solves the offline problem, try resetting the camera and reconnecting it.

Why does O-KAM Pro camera keep showing that it is connecting?

.

See also  How To Setup O-KAM Pro camera(Complete Manual)

.

You can also try:

If it’s a 4G O-KAM Pro camera, please detect if the SIM card’s is in arrears.

.

The Optiview VMS supports IP/Megapixel cameras, Analog, HD-over-Coax and IP/Network recorders. Another aspect of this powerful system is the fact that the 64-channel preview screens can be opened in up to 4 windows for live viewing up to 256 channels at the same time.

While all cameras will record on their local recorders, the VMS allows for up to 16 channels to record locally on the home or work PC. 36 channels can be chosen for playback in increments of 24 hour periods.

.

SOFTWARE DOWNLOADS

Right-click and select “Save Link As”

OTHER DOWNLOADS

VMX SERIES SUPPORT

Downloads / Files / Support

Welcome to the comprehensive support page for the Optiview VMX video monitoring platform. This platform, offering both VMX and VMX+ versions, is a potent, integrated solution for single and multi-site surveillance and access control systems. Whether you’re a first-time user or seasoned expert, we’re committed to ensuring that your experience with the Optiview VMX platform is seamless. This page is your hub for downloading all the necessary software and related materials for the Optiview VMX system. As always, if you need more in depth support, call our US based text support line at 904.855.1121.

.

OPTIVIEW VMX

INTEGRATED MULTI-SITE MANAGEMENT SYSTEM

for Single and Multi-Site Surveillance and Access Control Systems

OVERVIEW

The Optiview VMX and VMX+ remote viewing platforms are both powerful, all-in-one professional, project level video surveillance management software. The Optiview VMX Client can be downloaded for free, and will support up to 64 network cameras and intercoms, and supports 1 user account. View up to 512 cameras and 256 Video Intercom devices, integrate multiple access control units, and access advanced analytics by upgrading to the Optiview VMX+.

The Optiview VMX/+ provides user rights management, device management, alarm management, video wall output, and two-way audio. In addition to these VMS features, Optiview VMX/+ offers advanced features, including support for real-time face recognition and robust event management controls.

FEATURES

SOFTWARE DOWNLOADS

OTHER DOWNLOADS

To view the product pages for Optiview VMX Free and VMX Plus click the link below:

Optiview VMX Free

Optiview VMX+

COMPATIBILITY

Optiview VMX is compatible with all Optiview IP-enabled devices: network cameras, NVRs, DVRs, video intercom devices, and access control devices. The server is also compatible with the ONVIF protocol, so it can connect to ONVIF-enabled third-party devices, such as some of Optiview’s third party manufacturers. Call your account managers to talk about our compatability matching.

PLAYBACK

The Optiview VMX platform allows for quick and easy playback of surveillance footage from both the Live footage interface, and the Playback interface. Users can search by time, date, or event type. Users can also zoom in on the timeline, and drag through the timeline with video scrubbing. Download multiple video files at a time, take single frame snapshots, or a ‘burst’ of snapshots.

SMART SEARCH

Search through your surveillance footage quickly and efficiently by using Smart Search, and targeting the area of the screen where motion would have occurred.

INSTANT PLAYBACK

Thought you saw something? Click “Instant Playback” for an immediate jump back in time to 30 seconds in the past to re-review your surveillance footage.

MULTI-MONITOR SUPPORT

Take advantage of complete multi-monitors support.

ADVANCED REPORTING

The Optiview VMX supports heat map, people counting, ANPR license plate capture, attendance and access control reporting.

FLEXIBLE & SCALABLE

Optiview VMX+ supports up to 512 video channels, which includes up to thirty two (32) face recognition cameras. Easily add multiple recorders, cameras, and access control devices from a single-site or from multiple locations around the world.

FISHEYE CAMERA SUPPORT

The software features full support for Optiview Fisheye cameras. The software supports options for the Fisheye camera installation and supports dewarping Optiview’s 360° panoramic fisheye cameras in both live view, and in playback. Because dewarp happens at the software level, the video is always recorded in full fisheye, even if the live view is being dewarped. This allows viewers to see the entire video, and dewarp sections of the video at any given time.

Fisheye

Fisheye Dewarp X4

Fisheye Dewarp X8

REAL-TIME FACE RECOGNITION

The Optiview VMX/+ performs real-time facial recognition on up to two (2) / thirty two (32) channels simultaneously. The software captures and analyzes facial features to determine gender, age, expression, glasses, mustache, and mask, and then can record the faces and store the associated structured data. The server also filters incoming video to display faces that match target features. Facial recognition requires a camera that supports this feature.

ACCESS CONTROL & VIDEO INTERCOM

Optiview VMX offers full support and integration for access control and video intercom products to support a complete security and surveillance system. The server monitors door status and events, manages access rights, and support advanced rules management. In addition to access controls, the server supports two-way communication between intercom and control center.

MANAGEMENT OPERATIONS

The software manages the devices and the user accounts for an entire organization. Operators can assign different camera ranges, active use periods, and business roles for each user. The server also supports different schemes for various events, including IVS, to record and view all event history information.

VISITORS

Quickly register and customize access for visitors.

LPR

Capture license plates in a searchable database.

EMAP

Easily select cameras to view on map.

USERS

Create up to 100 Users per VMX Server.

EVENTS

Track entrance / exit, alarms, access, and more.

.

FREQUENTLY ASKED QUESTIONS

WHAT ARE THE MAJOR DIFFERENCES BETWEEN THE VMS AND THE VMX?

The Optiview VMS and the Optiview VMX are both multi-site remote monitoring software that can be used to view cameras and devices from a centralized location. The VMS is ideal for residential and commercial use, where basic camera surveillance is the primary need. The VMX, however, has an advanced access control module, and can support advanced surveillance such as facial recognition, traffic density, ANPR license plate database capture, and more. See which software is right for you here!

WHY DO I HAVE TO START USING THE VMX?

The free Optiview Video Management Software (VMS) is our legacy remote viewing software, and will no longer be supported going forward. Instead, download our all new Optiview VMX, our powerful new remote viewing software; The user is able to choose between a free VMX, and a more advanced VMX+ with additional features. The new VMX and VMX+ provide a more stable management and viewing platform for CCTV and Access Control, as well as providing many new features. Not sure which solution is right for you? Contact an Optiview Account Manager or compare the Optiview VMX and VMX+ here.

Features Gained:

Optiview’s VMX will support Optiview legacy equipment as well as the latest in megapixel, analytic, and edge recording technology.

WHAT IS THE DIFFERENCE BETWEEN THE FREE VMX AND PAID VMX+ VERSION?

The free version of the Optiview VMX supports 64 video channels, 2 ANPR channels, 2 facial recognition channels, 64 access control channels, 2 POS channels, 4 attendance devices, 2 alarms, and supports only 1 online user at a time.

The paid version allows the user up to a maximum of 512 video channels, 200 access control devices, 1024 doors, 32 video intercom devices, 32 facial recognition cameras, 100 alarms, 32 license plate capture cameras, and supports up to 100 online users.

See which software is right for you here!

WHEN WILL THE VMS STOP BEING SUPPORTED AND AVAILABLE?

The Optiview VMS 2018 will continue to be available to download for a limited amount of time, but will no longer be supported going forward.

WHAT IS THE MAXIMUM NUMBER OF DEVICES THAT CAN BE PUT ON THE FREE VMX OR THE PAID VMX+?

The free version of the Optiview VMX will suport up to 64 cameras. If the user wants to view more than 64 cameras, they will have to purchase the Base License, and then an additional license for each channel, up to 512. See which software is right for you here!

HOW DO I UPGRADE FROM THE VMS TO THE VMX?

The VMX software is completely different from the Optiview VMS and a user can use both. The VMX Server and Client software can be downloaded here.

WHAT IS THE DIFFERENCE BETWEEN THE VMX SERVER AND THE VMX CLIENT?

The server runs all the services and acts as a connection point for several clients that will handle the management of configurations, devices and integrations of one or more IP devices supported by the Optiview VMX software.

IF I HAVE THE SERVER DOWNLOADED, HOW DO I DOWNLOAD THE CLIENT?

The client can be downloaded using the link from the server user interface labeled as “Download Client”. I also made a link for the Client software within our technical support page which Georgia can use, to make a download link within the product resource page.

CAN I DESIGNATE THE NUMBER OF CAMERA CHANNELS BEING SEEN BY THE VMX PER DVR OR NVR?

Yes. The number of cameras “actually” in use by a device (for example a 32-ch NVR) can be designated within the VMX so that it can only sees the actual number of channels. For example, If a user is using multiple 32 channel recorders but not all channels, the VMX can be set to not count every single channel and maximize the usage.

CAN I DESIGNATE THE NUMBER OF ACCESS CONTROL DOORS BEING SEEN BY THE VMX?

No. Whatever the maximum number of doors that an access control panel can handle is, that is what the VMX will see. For example, a CAS-4MC (4 door master control panel) is expandable up to 64 doors, so this will max out the VMX. No additional master control panels can be added unless the user upgrades to the paid version of the Optiview VMX.

CAN I SEE THE HUMAN TEMPERATURE DETECTION & NOTIFICATION SOLUTION ON THE VMX?

The human temperature text overlay can be seen at LIVE mode and Playback mode at the VMX.

HOW MANY USERS CAN ACCESS THE VMX AT ONE TIME?

For the FREE version, only 1 user can access the VMX at any given time, regardless of how many clients are downloaded. With the paid version, up to 100 active users are able to access the VMX Server at any given time via multiple clients. See which software is right for you here!

.

 .

What is DMSS APP?

DMSS is a mobile surveillance app with functions like video playback, remote monitoring, device initialization, push notifications, and remote configuration. Devices like IPC, NVR, XVR, VTO, doorbells, alarms and access controllers can be added. After logging into the account, you can use cloud services like cloud upgrade and so on. The app supports iOS 9.0 and Android 5.0 or later systems and can be used with 3G/4G/Wi-Fi.

 .

What are the benefits of DMSS Camera App?

Remote operations

Before talking about DMSS Camera application on Alexa, let’s see what is DMSS? DMSS app can work in an environment with various internet connections. It connects Dahua CCTV products through both Internet and Ethernet. P2P-enabled internet connection shows great simplicity, while IP or domain name-enabled Ethernet connection guarantees strong stability.

DMSS can be operated remotely to immediately and stably control specific devices all around the world through its global network coverage. many functions including PTZ controlling, video preview and playback, video image adjustment (such as White Balance, focus, etc.), alarm subscription, voice intercom and etc. can be done remotely.

 .

increased data security

DMSS adopts multiple layers of data encryption protection to supply better data security to users.

From a product to the platform and then to the mobile client, DMSS uses multiple layers of data encryption protection to provide better data security to users. DMSS camera has also been certified by TÜV Rheinland, meaning the product complies with the GDPR and meets the TÜV Rheinland 2PfG 2624/06.17 standards, offering state-of-the-art information security and privacy protection.

Featuring a more detailed interaction design, DMSS provides a smoother user experience.

 .

Supports thermal products

To prepare the best support for the global efforts in pandemic prevention and control, DMSS CCTV also supports thermal products (supported by CCTV Suppliers), including access control, thermal cameras, and temperature monitoring terminals. It lets the operators control thermal products remotely and perform their duty in a safer manner.

 .

Setup DMSS App on Alexa amazon

Amazon Alexa is a virtual assistant AI technology developed by Amazon. It is able to voice interaction, music playback, make to-do lists, stream podcasts, set alarms, play audiobooks, and provide weather, traffic, sports, and other real-time information, such as news. Using itself as a home automation system, Alexa can also control your home security camera and even we can set up DMSS application on Alexa. Users are able to increase the Alexa capabilities by installing “skills” (additional functionality developed by third-party vendors, in other settings more commonly called apps) like weather programs and audio features.

Most devices with Alexa let users activate the device using a wake-word (like Alexa or Amazon); other devices (like the Amazon mobile app on iOS or Android and Amazon Dash Wand) require the user to click a button to activate Alexa’s listening mode, although, some phones also let a user say a command, such as “Alexa” or “Alexa wake”.

In September 2019, Amazon launched many new devices achieving many records while competing with the world’s smart home industry. The new Echo Studio became the first smart speaker with 360 sound and Dolby sound. Other new devices included an Echo dot with a clock behind the fabric, a new third-generation Amazon Echo, Echo Show 8, a plug-in Echo device, Echo Flex, Alexa built-in wireless earphones, Echo buds, Alexa built-in spectacles, Echo frames, and Alexa built-in Ring, and Echo Loop.

How to use Alexa for your home security camera?

Using Alexa with a home security camera adds comfort. You can use a smart display screen in your house to immediately and easily review past footage and see who’s at the door right now. Just make sure you have compatible devices and you’ll be using Alexa to check in on your camera (or cameras) in no time. One of the utilities of Alexa is setting up the DMSS application on Alexa. Let’s we how we can do it.

 .

DMSS application on Alexa: How does Alexa work with DMSS?

To add your Dahua device using the Amazon Alexa app:

Let’s assume that you’ve installed and configured your Alexa-compatible home security camera already and you have an Alexa-enabled smart speaker.

Now you need to log in to your Alexa app or make an account if you don’t already have one. Simply download the Alexa app and follow the prompts to sign in/register a new account.

Open the Alexa app and choose “Skills & Games” in the menu. Type “Ring” in the search box, open the skill, and choose “Enable.”

You’ll be asked to enter your Ring account credentials to pair your Ring account to the Alexa app.

 .

How to Download the DMSS Application?

The prefix “g” or “i” differentiate the applications intended for Android and iPhone/iPad and thus we will find them in the official Google Play and App Store:

Before, DMSS Plus was paid while you could get the Lite version for free. There are some differences between DMSS Lite and Plus such as E-Map (visual and functional installation plans), alarm management, and push notifications. Currently, there is no need to choose since Dahua has released the Plus version for free. In addition, this publication is already adapted to the new GDPR (General Data Protection Regulation).

 .

 .

Download Dahua DMSS software

View DMSS APP User Manual

 .

What Functions Do These Apps Offer?

The aforementioned applications have undergone several updates that improve their operation and increase their capabilities so sometimes it is difficult to follow all the news. Therefore, let’s see a summary of what they offer us for the management of our video surveillance devices:

Integration of Other Security Devices

The main novelty is managing DMSS CCTV devices, access control devices, and alarm systems from the manufacturer Dahua in a single app.

 .

Device Management

Among other options, they can be located within a local network (WiFi or LAN), and add devices via IP/Domain, DDNS, and P2P (Easy4IP and Lechange). This last option allows you to add devices by scanning the QR code and even a complete list of devices, very useful for migrating from the Lite app to the Plus version in a single operation.

 .

Live View and Playback of Recordings and Stored Clips

Live, to access and capture live video from added devices, combining channels and cameras. Playback, to consult, capture, cut, and extract the recorded videos. In addition to that, clips and captures can be viewed from the smartphone’s memory.

 .

Channel Configuration

It allows you to modify the coding (image resolution and ratio), image adjustments, PTZ or motorized zoom camera movement control, two-way audio communication with the device, and quadrant display, as more interesting functions.

 .

Notifications and Events

Detection events generated by devices are listed and notified in the app through push notifications. These consist of instant and free alerts supported by the devices and to which we can easily subscribe, depending on the type of detection selected.

 .

Cloud Recording, Cloud Storage Services

Upcoming updates will enable cloud video recording under a subscription service, with per-channel rates for 3, 7, or 30-day recording, and only for cameras that support such functionality.

 .

You can also check:

Best CCTV Brands in the UK

 .

 .

How to See Your Dahua DMSS Security Cameras from the Cell Phone

DMSS is Dahua ‘s free software to connect to your equipment from smartphones. It is used to connect to all current Dahua manufacturer equipment: DVR recorders, HDCVI, NVRs, IP cameras, etc.

This App can be downloaded for free in both the Play Store and the App Store. The Android version is called gDMSS and the iPhone iOS version is called iDMSS.

To connect your Dahua device via P2P on your cell phone, you are going to need:

 .

How to Configure Your Dahua Security Cameras in DMSS

Enter the SN of the device and touch the “Next” button.

Once all the boxes are completed, tap the “Save” button that is located at the top right.

If you followed the steps correctly, it should start viewing your security cameras live. By tapping the back button at the top left, you can return to Start.

 .

How to View Your Dahua Cameras in DMSS

If you followed the steps correctly, you should start viewing your security cameras live.

 .

 .

 .

The red numbered buttons:

 .

The Yellow numbered buttons:

 .

 .

Conclusion

As we saw, you know about DMSS App & can set up Alexa on your camera easily, just you need to go to the menu and tap Skills. Find the relevant skill (some cameras have specific apps for the cameras, outside of their main smart home apps). Enable the skill and link the account with Alexa. It’s a simple thing to set up and it means that you can create a security monitor without ever firing up your smartphone or tablet. All you need is one of the three Amazon devices noted in the intro and a compatible DMSS camera.

Features:

(Supported features depend on camera features)

For more information download the Alibi Cloud VS Mobile App User Guide.

iOS App

• 

.

Android App

• 

.

.

Alibi Cloud VS

Direct Camera to Cloud Video Surveillance

Our cutting edge cloud-based VSaaS offering has gained significant traction with dealers and end-users and is poised for significant growth in 2023 and beyond. If you are not selling cloud-based video surveillance then you are missing out on opportunities to recession-proof your business. We’ll be hosting demo sessions to show you how simple it is to install/setup and how it saves you time and money by avoiding truck rolls with an easy to use interface that helps you solve most issues remotely. And it is super easy for your customer to use as well, making it incredibly appealing for home and business installs.
Learn how this powerful solution is gaining traction in cannabis, medical, retail/restaurant and education applications.

.

Brivo Cloud Access Control

Brivo + Alibi Security: Better Together

Brivo and Alibi Security bring you the best of both worlds… Unlimited access to Brivo’s world-class solutions and support, plus Alibi’s dedicated sales support & innovative marketing platform. The Brivo Accelerate Program is designed to help accelerate growth of YOUR access control business!

.

Alibi Arsenal

Our FREE Marketing Engine, Ready to Power
Your Business

Marketing is not easy. Alibi Arsenal business growth tools and resources make it easier. This FREE platform can help you generate leads with brandable sales/marketing flyers, get found online with improved Google My Business setup and to turn your current customer base into advocates through a powerful reviews engine. Plus, we give you access to tools that make it easier to tap into your current customer base to generate incremental business by cross-selling products and services.
Come by for a LIVE demo of this platform and to learn how you access these powerful tools.

.

Expect More from
Your Security Provider

.

Alibi Security is a trusted provider of security technology, cloud solutions, and growth enablement services—serving thousands of security professionals for more than 35 years. We are committed to quality, continuous innovation, and the investment in the PEOPLE, SOLUTIONS, and SUPPORT required to help our Dealer Partners succeed.

.

.

Enterprise Performance
– Without Breaking the Bank

Alibi Cloud VS makes enterprise-level cloud surveillance accessible for virtually any-sized application or budget. Featuring an ultra-secure camera-to-cloud architecture, Alibi Cloud VS dramatically reduces your up-front hardware investment and maintenance requirements, saving you valuable time and money. Ideal for both business and residential applications, Alibi Cloud VS is remarkably scalable – and can easily support larger camera counts and multi-site projects.

Centralized
Management

View cameras from single or multiple locations via a single dashboard, simplifying management and streamlining review of your video evidence.

Eliminate Common
Failure Points

Stream directly from camera to the cloud, ensuring you never lose video footage due to a faulty recorder or failed hard drive.

Enhanced
Security

No port forwarding necessary. SSL/TSL handshakes are used to make the connection from camera to cloud, ensuring encrypted transmission up and down. Video is stored in ultra-secure Tier 4 data centers, featuring triple-redundancy and fault-tolerant infrastructure to ensure your evidence is always safe.

Lower Total Cost of
Ownership (TCO)

No recording equipment, minimal maintenance requirements, and on-demand scalability – so you only pay for what you need, when you need it.

.

.

Before referring to this Mobile Application User Guide you must first download and install the mobile application on your mobile device (smartphone or tablet). You can find links to the mobile application(s) on www.alibisecurity.com at the following location:

.

SUPPORT Menu > DOWNLOADS > ALIBI CLOUD VS MOBILE APP

.

Choose the link that applies to your mobile device (iOS or Android), download and install the application. Now you are ready to install and activate cameras.

.

Adding a Camera via the Mobile Application

.

The first time you login to the mobile app, you will be required to enter your username (email address) and the password. The screen will show no cameras attached to your account. You will tap the ADD A CAMERA button on the screen and it will prompt you with a second screen to select the type of camera you want to install. Tap on the ADD A CLOUD CAM section. The next screen gives you specific instructions for attaching your cloud-enabled camera to the network.

.

IMPORTANT: All POE and WiFi cameras must be hard-wired into the local network in order to be discovered by the Alibi Cloud VS solution.

.

Once you have connected the cameras you want to add to your Alibi Cloud VS account to the local area network (LAN) you can tap the CONTINUE button.

.

.

..

.

The next screen displays your local network and the cameras that are available to be added to your Alibi Cloud VS account. Tap on the camera you want to add from the list and you will be prompted to name your camera. Type in a name and choose CONTINUE. The system will ping your camera, check credentials and firmware and connect. You should receive a confirmation screen that the camera has been added then tap CONTINUE.

.

.

.

..

.

To get your WiFi camera to the wireless network you need to connect the WiFi camera to the wireless network. Tap the zone that the WiFi camera is in. This takes you into the camera selector menu. Select the WiFi camera you want to attach and it will open the camera settings menu. On the main screen, under NETWORK

SETTINGS, it will say “Not Connected”. Select this menu option and it will take you into the wireless connection menu, displaying the available wireless networks to connect to.

.

.

.

.

Tap the wireless network you want to attach the camera to. A login screen will open up asking you to enter the password for the wireless network. Enter the password and tap CONNECT. The system will them connect the camera to the wireless network and you will receive a confirmation screen once completed.

.

IMPORTANT: You must keep the WiFi camera hard-wired into the network until you login to the wireless network. Once you get the camera connected to the wireless network you can disconnect the network cable and move the camera anywhere that it has good signal strength to connect to the wireless network.

.

.

.

.

.

.

From the main dashboard screen you have two different ways you can add additional cameras to the system. If you want to add another camera to the same zone you already have setup, simply choose the zone on the main dashboard screen, it will pull up the camera viewing screen and you will tap the Gear icon at the bottom. It will open a screen that shows the current camera(s) assigned to the zone and the ADD A NEW CAMERA button.

Tap this and follow the instructions to add a new camera.

.

.

The second option for adding cameras is to setup a new zone and add the camera to that new zone. From the main dashboard screen tap the + icon in the top left corner of the screen. This opens a new screen that lets you setup a new zone. Click ADD CAMERA and then follow the instructions for adding a new camera explained previously in the User Guide.

.

.

From this menu you can also move cameras currently signed to other zones to the new zone. Simply click SELECT CAMERAS FROM OTHER ZONES. A menu will be displayed showing cameras already attached to other zones. Click the camera and move it to the new zone.

.

After adding the camera you will be taken to the main camera dashboard screen. From this view you can see all of the zones cameras have been assigned to. Select the zone you want to view. An individual thumbnail view of the camera(s) will be displayed. Tap on the gear icon at the bottom of the screen and it will take you into the settings selection menu. Choose the arrow to the right of the camera that you want to adjust settings for and you will be taken to the settings menu for that specific camera.

.

.

.

.

.

.

.

.

.

.

.

PoE Camera Setting Menu

.

.

.

.

.

.

.

WiFi Camera Setting Menu

.

In the settings menu for each camera you are able to control the following settings:

.

.

Account Settings and TouchID/FaceID Login

.

After you login and add a camera to your system you can select the home button at the bottom left of the screen and it will take you to your main dashboard. Select the person icon in the upper right and this will take you into account settings. From here you can enable remote support access, enable/disable push notifications and enable TouchID/FaceID login for easy access when starting the app.

To view live video from your cameras connected to Alibi Cloud VS, go to the main dashboard screen and select a zone to view. Once in the zone, you will see the individual cameras with ‘play arrows’ located in the middle of the thumbnail screen. Simply click on one of the ‘play arrows’ in the thumbnail and live viewing will begin. You will see the word “LIVE” appear at the top of the thumbnail viewing screen. Want to enlarge the viewing area? You can simply turn your smartphone/mobile device to landscape to view in full screen mode.

.

Viewing recorded video (footage) is also very simple. You will need to choose the zone that includes the camera you want to review recorded video from. This will display thumbnail views of all cameras associated with this zone. If you have multiple cameras in a zone, you will see multiple thumbnails. To view recorded footage for

a specific camera tap the clock/rewind icon ( ) at the bottom of that camera thumbnail view. This will take you into the footage screen where you can review a timeline, with detection events noted. You can scroll through the timeline by scrolling with your finger, either up or down, to view events that happened earlier or later in the day.

.

.

There are settings and features on the playback screen that make it easier for you to review video quickly. You can select the ZOOM IN button and the timeline will appear in smaller increments, allowing you to find events more accurately. You tap the MORE menu and adjust playback up to 10x faster than normal.

The SUMMARY button at the bottom of the page lets you create and download a video summary of detection events for the last 24 hours. Simply click the button and the app pulls detection events into a single summary video. Creating a summary takes a few minutes and once completed you have the option to save the 24 hour summary to your mobile device or share it with someone else.

.

If you have forgotten your password or simply want to reset it, you can easily do this by selecting the person icon in the main dashboard screen. Click ‘Logout’ and on the next screen tap ‘Log In’ and it will take you to the main login page. Tap ‘Forgot Your Password?’ and a screen will appear for you to enter your email address. By entering your email address and clicking ‘Send’ you will receive a secure link in your email to reset your password for your Alibi Cloud VS account. This new password will be valid in desktop and mobile apps.

.

.

The tool allows adding and monitoring a large number of cameras simultaneously. The cameras in your network can be automatically found and installed. The program supports IP and P2P connection modes as well as UMSP, HZXM, and HZZN protocols. It could also be necessary to provide the camera’s password to access it. After this step, the devices can be organized by grouping them into different folders. For monitoring purposes, it is possible to divide the workspace into up to 64 regions. Moreover, on the left, there is a panel, from which you can control the selected camera.

In addition to allowing the users to view live video streams, the program also lets you schedule recording sessions and play them later. Likewise, it can take snapshots of specific video frames. Moreover, you can implement alarms to send notifications to a given SMS number.

All in all, QmEye is an excellent solution in terms of the number of cameras and connection protocols allowed. Unfortunately, the tool is not as easy to use as other similar tools and its graphical user interface probably needs a redesign.

This manual has mainly instructions on the installation and usage in Android, iPhone mobile phone.

1.Android

This cloud service platform is the best mobile phone video during the internet era. It consists of front-end acquisition devices, platform servers, and remote view of three parts.

Open the software into the login interface, inputting the username and password and click button “login”, then it will be login the application.

Icon description：

Notice: Please click “LoginFree”, directly into the system, without verifying user name and password. And you can get help information without login.
1.1 User register
User register

Click the button “register” on the login menu, then will jump to the register interface.

Enter the register information, click “register” then will be registered.
Note:1 please enter the valid E-mail address in order to retrieve your password when you lost it.

2 No account login version, no such function! 

retrieve the password

On the register clicking the button “login” and jump to “retrieve password” interface.

Input the username, click button “retrieve password”.

If you have entered your name and email address when registering and the username has been occupied, then “retrieve password” information will be sent to the email address.

QMeye User Manual 2024

1.2 Real-time preview

In the main menu, clicking “real-time preview
Click “Favorites” button, go to “collection management” interface

Click on the icon, favorites list change into editing state, click icon, you can delete your favorites.
Select one of the devices on “Live list” enters the video preview interface.

Button instruction：

1.3 device management

Click the button” device management” on the main menu and enter “device management” interface.

Icon instruction：

Modify the connection parameter

Click on the icon, select “modify connect parameter”, then into “modify device” dialog box：

A）Click on the icon, return to the device management lists.
B）Click on the icon, save the current configuration.

Modify the name

Click on the icon, select the option “modify the name”, then pops up “modify name” or “modify the catalogue” dialog box.

A）Click “OK” button to save the current configuration.
B）Click “cancel” button to cancel the modifying.
Delete

Click on icon, select “delete’ button to delete the current device directly
Add the catalogue

Click on icon, select “add the catalogue” option, then pops up “add the catalogue” dialog box

A）Click “OK” button, it will be saved the current configuration. Then will be showed in the device management list.
B）Click button “Cancel” to cancel to add the catalogue.
Add the device

Click on the icon to select “add the device” option.

Icon instruction

Add the shot

Please see the operation introduction of “add devices”.

Search the local device

Click on the icon to enter “search” dialog box. If there are some devices in local place, you would search out the corresponding device.

Icon instruction

Click on the icon, then pop up the menu as follows:

A）Add a device: add DVR (multi- channel)
B）Add a shot: add a single camera (single channel)
C）Modify the name: modify the name of the device or shot
D）Modify IP: Modify the IP address, subnet mask, gateway information
E）Modify the device password

1.4 Playback

Click button “playback” option in the main menu, and then select to playback the video.

After select an event type, start time and end time, clicking on the icon will list out the remote video lists, and then click on the item will be selected to play or download videos.

1.5 Alarm management

Click the option of “alarm management” in the main menu

Icon instruction：

Guard

Click on the icon to select “guard” option, pop up the dialog box as follows:

Select the option those need to alarm and click the button “setup” to save the current settings; Click the button “cancel” to cancel the current settings.

Unguard

Click on the icon to select the button “unguard”, cancel the current camera setting.

Note

Click on the icon to select “note” option, and then pop up the dialog as follows:

A）SMS notification: set the cell phone number of alarm notification
B）News push: open/ close the news push setting
In the notification interface, and then into “SMS notification” interface

Icon instruction

Record

Click on the icon to select “record” option, and then pop up the dialog of “alarm record”

The icons instruction

1.6 Local playback

Click on “local playback” option in the main menu, and then into the interface as follows

Click on the icon, the local playback video list change to editing states.

Select the video options that you want to delete, and then click the icon; you can delete the selected local video.

1.7 Image view

Click on “images browsing” option

Click on the icon, the local playback video list change to editing states.

Select the image options that you want to delete, and then click on the icon to delete the selected local images.

1.8 Modify password

Click on” modify password” option in the main menu, and then into the interface as follows:

Click on the icon to save the current modified password.

1.9 Local configuration

Click on “local configuration” option in the main menu, and then into the interface as follows

Function instruction：

Click on the icon to save the current configuration.

.

.

.

.

.

.

.

.

.

.

.

.

2、iphone

.

Open the software into the login interface, inputting the username and password and click button “login”, then it will be login the application.

Icon description：

Notice: Please click “LoginFree”, directly into the system, without verifying user name and password. And you can get help information without login.

.

2.1 User register

User register

Click the button “register” on the login menu, then will jump to the register interface.

Enter the register information, click “register” then will be registered.
Note: 1 please enter the valid E-mail address in order to retrieve your password when you lost it.

2 No account login version, no such function! 
retrieve the password

On the register clicking the button “login” and jump to “Retrieve password” interface.

Input the username, click button “retrieve password”.
If you have entered your name and email address when registering and the username has been occupied, then “retrieve password” information will be sent to the email address.
.

2.2 Real-time preview

In the main menu, clicking “real-time preview
Click “Favorites” button, go to “collection management” interface

Select one of the devices on “Live list” enters the video preview interface.

  

Button instruction：

2.3 device management

Click the button” device management” on the main menu and enter “device management” interface.

Icon instruction：

Modify the connection parameter

Click on the icon, select “modify connect parameter”, then into “modify device” dialog box：

A）Click on the icon, return to the device management lists.
B）Click on the icon, save the current configuration.
Modify the name

Click on the icon, select the option “modify the name”, then pops up “modify name” or “modify the catalogue” dialog box.

A）Click “OK” button to save the current configuration.
B）Click “cancel” button to cancel the modifying.

Delete

Click on icon, select “delete’ button to delete the current device directly

Add the catalogue

Click on icon, select “add the catalogue” option, then pops up “add the catalogue” dialog box

A）Click “OK” button, it will be saved the current configuration. Then will be showed in the device management list.
B）Click button “Cancel” to cancel to add the catalogue.

Add the device

Click on the icon to select “add the device” option.

Icon instruction

Add the shot

Please see the operation introduction of “add devices”.

Search the local device

Click on the icon to enter “Device search” dialog box. If there are some devices in local place, you would search out the corresponding device.

Icon instruction

Click on the icon, then pop up the menu as follows:

A）Add a device: add DVR (multi- channel)
B）Add a shot: add a single camera (single channel)
C）Modify the name: modify the name of the device or shot
D）Modify IP: Modify the IP address, subnet mask, gateway information
E）Modify the device password
.

2.4 Playback

Click button “playback” option in the main menu, and then select to playback the video.

After select an event type, start time and end time, click the button OK will list out the remote video lists, and then click on the item will be selected to play or download videos.

2.5 Alarm management

Click the option of “alarm management” in the main menu

Icon instruction：

Guard

Click on the icon to select “guard” option, pop up the dialog box as follows:

Select the option those need to alarm and click the button “OK” to save the current settings; Click the button “Cancel” to cancel the current settings.

Unguard

Click on the icon to select the button “unguard”, cancel the current camera setting.

Note

Click on the icon to select “note” option, and then pop up the dialog as follows:

A）SMS notification: set the cell phone number of alarm notification
B）Message push: open/ close the news push setting

In the notification interface, and then into “SMS notification” interface

Icon instruction

.

Record

Click on the icon to select “record” option, and then pop up the dialog of “alarm record”

The icons instruction

.

2.6 Local playback

Click on “local playback” option in the main menu, and then into the interface as follows

Click on the icon, the local playback video list change to editing states.

Select the video options that you want to delete, and then click the button “delete”; you can delete the selected local video.

2.7 Image view

Click on “images browsing” option

Click on the icon, the local playback video list change to editing states.

Select the image options that you want to delete, and then click on the button delete to delete the selected local images.

2.8 Modify password

Click on” modify password” option in the main menu, and then into the interface as follows:

Click on the icon to save the current modified password.

2.9 Local configuration

Click on “local configuration” option in the main menu, and then into the interface as follows

Function instruction：

Click on the icon to save the current configuration.

.

.

QmEye_PC_Client_

1、Install

Double-click to open QmEye installation file, pop up following the installation wizard(The version number may be different, but not influence use)

.

Click “next” until the following interface, click the “install”

.

After the installation of software, pop-up window as follows:

.

Click “finish”

.

.

.

.

2.1 Login

Start the application, the program into the landing interface, as shown in P2-1

.

P2-1 Login

  Enter account and password to log in. If the user does not have the account , you can apply for to register.  And local login is permitted.

2.2 Register

Clicks the “register” on the login interface, enter the registration screen, as shown in P2-2.

.

P2-2 Register

With * is required, fill in and then click the “register”.

2.3 Password lost

If users have account, but forget the login password.You can through the e-mail to retrieve password. Click “Password lost”, Enter the following interface

.

图2-3 Password lost

  Mail QueryL: Check the reserved E-mail information when registering.

  Retrieve Password: System will send an email to the email, according to the prompt to reset the login password

2.4 Main Interface

  After the success of the user login, enter the main interface, as shown in P2-4.

.

P2-4 main interface

  Main interface is divided into four parts, including at the top of the navigation bar(P2-5), he left menu bar – device list and function(P2-6), in the middle of the play rect(P2-7), And at the bottom of the play controls(P2-8)

.

P2-5 Navigation bar

.

P2-6 Device list and function

.

P2-7 The play rect

.

P2-8 Play controls

  The description of each icon function as the following:

2.5 Control panel

.

Picture 2-9 control panel

  .

Screen locking: Lock the screen, in the lock case is not able to do any operation in current interface apart from unlocking.(PS: It is not permitted, on local login mode.)

Log off: logout the client

Playback: to playback the remote video and local video

Photos: view local images save by capture

Password Correcting: modify the user logon password(PS: It is not permitted, on local login mode.)

Alarm Settings: set the front-end device booted and alarm monitoring types(PS: It is not permitted, on local login mode.)

Device Searching: search all device which in LAN

DeviceAdministration: for operation such as rename, add, delete a device.

2.6 Add the Device

2.6.1 Quick Add

     “Control Panel” ->” Device Searching”, then pop up the device searching interface, as shown in P2-10

.

P2-10 search the device

  .

     Select out a device is searched, and then click “add to the list” filling device login ID and password, as showed in P2-11

.

P2-11 add a device to lists

.

Parent directory: add the camera to specific catalogue

Scene name: add to the display name of the user to the device lists.

Username: login username of the device

Password: the login password of the device

Channel NO: view what channel number, start from 1. Completed IPC as 1

Streaming: request to a front- end device stream format while live preview, default is sub stream. Fulfill the above information: after finished, click “add” button

.

.

图2-12

2.6.2Add the device manually

  .

“Control the panel” ->”Device management”, then pop up the device management interface, as shown in figure 2-13

.

.

Picture 2-13 device management

Firstly, select a directory from the device list box, then click “add the cameras” enter the added interface like the following figure:

.

Picture 2-14 add cameras

  .

     Device name: the display name that you add to the user device list, more convenient to people identify (such as living room)

    Device type: lens (the channel of the IPC, DVR\NVR), device (such as DVR\NVR)

    Connection modes: (IP address and port access mode), P2P (cloud- penetration mode)

    Protocol: select the front-end device protocol

Cloud ID: front-end device ID to identify the device, P2P mode exclusive.

Username: the login username of device

Password: device login password

    Channel NO: view what channel number, start from 1. Completed IPC as 1 (if it is the device type, it is the channel number mean: complete 8 if is 8Channel DVR)

    Stream: request to a front- end device stream format while live preview, 0 is main stream,1 is sub stream, default is sub stream.

.

2.7 Alarm setting

“Control the panel” ->”alarm configuration”, then pop up the alarm setting interface, as shown in figure 2-15

.

.

Picture 2-15 alarm setting

     Guard: start 4 alarm types monitoring which you tick

      Unguard: cancel all alarm types monitoring

PC Push: after booting and the related equipment alarm is triggered, the server will push the information to the PC client and prompt the user

Add number: add SMS notice number

Delete number: delete SMS notice number

Turn off the alarm: turn off the alarm, which the PC client is no longer to prompt the push information of device trigger alarm

Open the alarm: turn on the alarm, which the Pc client will prompt the push information of device trigger alarm.

View the alarm information: after starting current PC to view all alarms push messages.

    .

2.8Video playback

2.8.1 Remote video playback

  .

“Control the panel” ->”video playback”, then pop up the video select operation interface, (as shown in figure 2-16), select “remote video” then into remote video playback interface, as shoun in figure 2-17

.

.

Picture 2-16 video types select

.

.

Picture 2-17 remote video playback

      Select a device and set up the query time then click it to acquire the relevant video information. as shown in figure 2-18

.

Picture 2-18 remote video lists

.

  Double click a video to play in the video lists (as follows), double click the playing interface can be full screen.

.

Picture 2-19 remote video playback

2.8.2 Local video

“Control the panel” ->”video playback” -> “local video”, then pop up the local video interface, (as following:

.

.

    Select the local video date that need to view. Query the related video and double click to play.

.

IP Camera

IE Browser User Manual

Preface

Thank you for using our IP camera products. This series of products are all-in-one IP cameras designed for network video surveillance, including box IP camera, infrared box IP camera, dome IP camera, speed dome IP camera, etc. The products adopt high performance and powerful single SOC chip media processor to integrate audio and video capture, compression and transmission. Standard H.264 Baseline and Main Profile coding algorithm ensures clearer and smoother video transmission effect. Built-in Web Server allows users to easily perform real-time monitoring and remote control over front-end cameras via IE browser.

This series of IP cameras is suitable for small and medium-sized enterprises, families, and other environments that require remote network video transmission and monitoring. It is easy to install and operate.

.

.

.

Statement:

.

.

.

.

Readership:

  This manual is suitable for engineers as follow:

.

Notes:

GV-Cloud VMS is suitable for businesses of all sizes. The cloud solution is easily scalable to meet the increasing need for more cameras and storage capacity. User and camera permissions can be grouped to align with the structure of a corporation. Overall, the cloud solution streamlines video surveillance while increasing infrastructure flexibility and scalability.

.

.

GV-Cloud VMS is a cloud-based video surveillance and data center solution. Thousands of on-site cameras, alarm devices, motion triggers and AI events can be efficiently monitored from a single cloud-powered platform. With GV-Cloud VMS, you can effortlessly access live streams, review playbacks, and query events from anywhere using a web browser.

.

GV-Cloud VMS is suitable for businesses of all sizes. The cloud solution is easily scalable to meet the increasing need for more cameras and storage capacity. User and camera permissions can be grouped to align with the structure of a corporation. Overall, the cloud solution can streamline video surveillance while increasing infrastructure flexibility and scalability.

.

Local Devices

Cloud Features

.

GV-Cloud Bridge for

ONVIF and GV-IP cameras

GV-VMS

Live View

Event Snapshot

Cloud Backup

.

GV-Cloud Camera

GV-AI Guard

GV-Cloud VMS (cloud-based SW)

Local Playback

System Health

Share Link

Archive

Mobile App

.

.

.

The following browsers are compatible with GV-Cloud VMS.

.

Note: The WS player is not supported by Safari.

.

.

.

GV-Cloud VMS has the following types of licenses. For details, please contact our sales representatives.

.

.

.

Chapter 2 Getting Started

.

To get started, you must acquire a GV-Cloud VMS license and a series number from GeoVision.

.

.

.

.

.

.

.

IMPORTANT: Keep your account ID number, which is required each time you log into GV- Cloud.

.

.Note: The mobile phone number can be used for the two-factor authentication if needed. See 5.3 Two-Factor Authentication.

.

For first-time users, you need to add a license to start the services.

.

.

.

.

.

.

.

.

You must create a Host for each GV-VMS, GV-AI Guard, or GV-Cloud Bridge that you want to connect to. To create a host on GV-Cloud VMS, follow the steps below.

.

1.Select Hosts in the left menu, and click  at the top right. This dialog box appears.

.

.

.

.

The message “Host has been added” will be displayed. Keep the Host Code and Password

for configuring the connection to GV-Cloud on the host.

.

.

.

Note: To reset the password, select a host in the Hosts list, and click the Edit Info icon next to the Info tab. See [Info], 4.1 Hosts.

.

.

.

Follow the steps below to connect GV-VMS or GV-AI Guard to GV-Cloud VMS for cloud central monitoring.

.

.

Note: The support for GV-AI Guard is coming soon.

.

.

.

In GV-VMS / GV-AI Guard:

1.Click Home > Toolbar > Network > Connect to GV-Cloud. A dialog box appears.

.

.

In GV-Cloud VMS:

When the GV-Cloud VMS connection is established, the host will be displayed, with a yellow icon or a green icon , on the GV-Cloud VMS Home page.

.

Without a license, you can view live streaming from the host.

.

.

By adding a license, you can receive snapshots or back up video to GV-Cloud VMS. For details, see 2.2 Adding Licenses.

.

.

Note:

1.If the GV-Cloud VMS connection fails in GV-VMS / GV-AI Guard, check to see if

WebCam Server and Mobile Service are enabled alongside Connect to GV-Cloud.

2.The yellow icon indicates that some of the host’s cameras are disconnected, while the green icon indicates that all of the host’s cameras are connected.

3..For camera events, only motion and video lost will be sent to GV-Cloud VMS by default. To send additional camera event types to GV-Cloud VMS, see 2.4.1 Configuring Advanced Settings.

.

.

.

.

To specify which events should be sent to GV-Cloud VMS, click the Configure button on the Connect to GV-Cloud dialog box. Three types of settings are available: General, Camera, and I/O Device.

.

[General]

.

Figure 2-6

[Startup]

.

.

.

[Connection Broken]

.

.

[Notify GV-Cloud when the following events occur] Select which events to notify GV- Cloud VMS about. Click Modify to adjust the threshold for sending notifications when the free storage space or keep days falls below the threshold.

.

.

[Temp Folder] The path to store logs and recordings to be sent to GV-Cloud VMS.

.

.

[Camera]

.

.

[Notify GV-Cloud of the monitoring status] Notify GV-Cloud VMS whenever camera monitoring is enabled or disabled.

[Notify GV-Cloud when the following events occur] Select a camera from the list, and then select the type of event or data to be sent to GV-Cloud VMS. By double-clicking the following two fields, you can specify the alarm conditions for specific events.

.

.

Tip: To apply the same settings to all cameras in the list, click the Apply All button .

.

[I/O Device]

.

.

Figure 2-8

[Notify GV-Cloud of the monitoring status] Notify GV-Cloud VMS whenever I/O monitoring is enabled or disabled.

.

.

[Input] Select an Input device from the list.

[Output] Select an output device the list.

.

.

.

You can connect up to four ONVIF cameras, through GV-Cloud Bridge, to GV-Cloud VMS for cloud central monitoring.

.

In GV-Cloud Bridge:

.

.

.

In GV-Cloud VMS:

When the GV-Cloud VMS connection is established, the host will be displayed, with a yellow icon or a green icon . on the GV-Cloud VMS Home page.

.

Without a license, you can view live streaming from the host.

.

.

.

.

By adding a license, you can receive snapshots or back up video to GV-Cloud VMS. For details, see 2.2 Adding Licenses.

.

.

.

Note:

1.To ensure a smooth playback on GV-Cloud VMS, it is suggested to connect a maximum of 2 cameras for the 4 MP license plan, 3 cameras for 2 MP license plan, and 4 cameras for 720p and SD license plan.

2..The yellow icon indicates that some of the host’s cameras are disconnected, while the green icon indicates that all of the host’s cameras are connected.

.

Chapter 3 Home Page

.

.

.

.

1

5

6

2

3

4

.

.

.

.