DVRCMS.Com

Connecting multiple IP Cameras together v1

admin — Mon, 22 Apr 2024 11:37:44 +0000

Connecting multiple IP Cameras together v1, As IP cameras become more affordable, it’s becoming common for people to expand their IP CCTV while minimising additional installation costs or efforts. However, the key challenge has always been setting up a new Cat5/6 cable to connect the camera to the rest of the system.

In scenarios where you already have a cable installed between the network and, say, your garage, where installing more cables is difficult, having to run a second cable is not ideal. However, we’ve discovered the Vigitron Netmux Vi00103 POE Multiplexer, a great gadget that combines two POE ports on your network side into one cable, and then splits them again at the camera-end, to solve this problem.

Below is some more important information on the specification and capabilities of the Vi00103, as well as our 6-step instructions for using it correctly.
.

Connecting multiple IP Cameras together v1.

Instructions:

Step 1:
.

Connect the two RJ45 cables from the Vi00103RX combiner, labelled “Port 1” and “Port 2”, to two available POE ports on your POE switch or NVR.

NOTE – The cameras do not need to be activated with a password. If you are connecting them directly to an NVR, then the Plug & Play feature will still work and activate the cameras; If you are connecting them to a separate POE switch, you will be able to access them and activate them on your network later. Plug & Play setups will also work when cameras have already been activated, as long that these are set with the same password as the NVR and have DHCP enabled.

Step 2:
.

Connect your single Cat5/6 cable to the port on the Vi00103RX combiner, which is labelled as “Port 1 + Port 2”.

Step 3:
.

Now, plug in the other end of the long single cable to the Vi00103TX splitter’s “Port 1 + Port 2” RJ45 port.

NOTE – this cable cannot be longer than 100m / 320 feet

Step 4:
.

Connect your IEEE802.3af/at IP cameras or POE devices to each of the ports, labelled “Port 1” and “Port 2”, using another Cat5/6 cable for each.

NOTE – the length of these cables, and the long single cable between the Vi00103RX and Vi00103TX cannot exceed 100m / 320 feet in total, as this is the maximum standard range of POE.

Step 5:
.

Green lights should appear on the Vi00103TX to confirm that each of the ports is delivering POE to your devices. If they do not, check the power supply to your POE source and all of your Cat5/6 cables are secure.

Step 6:
.

If you are connecting the cameras directly to an NVR as “Plug & Play”, then they will connect and appear automatically after a minute or two. Alternatively, if you are connecting them to a separate POE switch, then they should be discoverable on the network and allow you to adjust any network settings so you can add them to your CCTV system.

Key benefits:

• Allows you to use a single cable for two cameras

• Useful if you already have a cable in place but want to add an additional camera without the hassle of routing another cable.

• Works with NVRs with POE ports and a Plug & Play feature, as well as on separate PoE switches.

• Entirely passive system (no additional power supply is needed).

• Compatible with PoE+ (IEEE802.3at) on both ports.

• There is an LED on each port of the splitter device to indicate the POE status.

Limitations & key points to consider:

• Two free ports on your POE source are still required.

• When setting up your cameras, it’s important to take into account the POE budget of your switch. Keep in mind that this budget won’t decrease the power draw per camera.

• Use a high-quality cable and ensure proper termination to avoid issues with transferring data to both cameras, as twice the amount of data will be transferred.

• Provides up to 37W of power to each device, with a total power budget of 74W.

• Only compatible with IEEE802.3af (regular POE) and IEEE802.3at (POE+) devices.

• It’s important to note that the cable run between the combiner and splitter devices should not exceed 100m. However, you can easily extend this by up to 100m with the Vi2300 UTP extenders.

• Keep in mind that the cable length from the POE switch to the cameras should not exceed 100m either. If your cable is already 80m, then the cables running between the splitter and each camera must be under 20m.

Network topology diagram & dimensions:

Can I connect more than one camera via a POE switch to a single POE port on my Hikvision NVR?

In some scenarios, it can be useful to have several cameras connected to a POE switch but to keep that switch directly connected to your NVR rather than the local network.

If you are able to connect each camera to its own POE port on your NVR, then this is generally advisable, as using a Plug & Play setup is much simpler and avoids the need for extra hardware or power supplies.

However, if your NVR is closer to your POE switch than it is an available access point to your LAN, then it can make connecting the cameras simpler whilst avoiding the need to have an ethernet cable running from each camera back to the NVR.

One other benefit of keeping the cameras connected directly to your NVR this way, rather than connecting them across your LAN, is that the connection does not rely on your router being operational. Provided the NVR and POE switch are working, the cameras will remain connected and recording regardless of any problems that might occur with your local network.

These seven steps below explain how to connect multiple cameras on a POE switch to a single port on your NVR.
.

1.Plug each camera into a numbered port on your POE switch and connect the switch to your LAN (router) via the Data/uplink port, so those cameras are visible in SADP on your PC.

2.Activate any camera that shows as “inactive” with a password.

NB – keeping the same password for each will simplify the entire process.

3.Turn on DHCP on each camera by selecting them in the SADP tool and ticking Enable DHCP in the right-hand window. Enter your password and click Modify to save the change. This is key for everything to work.

4.Now, disconnect the POE switch from your network and reconnect it to your chosen POE port on the NVR, whilst keeping the power supply to the switch connected.

5.Disable the NVR’s POE on the channels that the switch is connected to and those that you have reserved for the cameras. To do this, open the NVR’s web GUI and navigate to Configuration > System > Channel Management > POE Channel. From there, untick the channels you want to disable and click Save.

NB – for example, if your POE switch is connected to port 8 of the NVR, and you would like to add your cameras to ports 1, 2 and 3, then you will need to disable the POE on ports 1, 2, 3 and 8.

6.Go to Configuration > System > Channel Management > IP Camera, and click Quick Add. This will bring up a list of the IP cameras connected to your local network, as well as the ones connected to the POE switch. Select the cameras with a 192.168.254.X IP address, as these addresses are on the NVR’s IP range and so must be the cameras connected directly to the NVR via the switch.

7.Once you have ticked the box for each camera you would like to add, click on OK to add them to the reserved channels. After a few seconds, the Status column for those cameras should change to Online, indicating they have been successfully connected.

Important things to note:

• Unless you are using a 12V power supply for your cameras, this will only work with a POE switch, as the ethernet ports will need to provide power to the cameras and a normal network switch does not allow power to pass through it from the NVR’s POE ports.

• If the power supply from your switch is disconnected then your cameras will stop recording to the NVR.

• Please ensure your POE switch has a suitable power budget to handle the cameras you plan to connect to it. The maximum power draw of a camera can be found in its datasheet.

• This will only work with Hikvision cameras, so anything added using the ONVIF protocol must be connected to its own POE port on the NVR or across your local network via a different switch.

• If the cameras are not connecting with DHCP enabled, then you can also manually assign the correct IP address for the channel you would like to put the camera on using the SADP tool.
These should be 192.168.254.2 for channel D1; 192.168.254.3 for channel D2; 192.168.254.4 for channel D3; and so on… The final number of the IP should be one higher than the channel.
The gateway address should also be set as 192.168.254.1.
You should then be able to add the cameras either via the Quick Add button or by the Manual adding method when clicking the edit button for that channel.

How do I use a Hikvision NVR’s “Virtual Host” feature?

One of the most successful selling points of a Hikvision NVR to many small-setup customers is the “Plug and Play” functionality that simplifies the setup process of their surveillance system. However, plugging a camera directly into a port on the NVR, unfortunately, does not allow you to access the camera via its own internal LAN IP using a browser due to it being on the NVRs internal network, and this can significantly reduce the number of configuration options you have access to.

The NVR does allow you to configure many options for each connected camera, but some essential features are only accessible via connecting to the camera itself (such as audio codec options). This was of course a big problem previously.

With the advent of newer firmware and models of NVR, Hikvision has introduced a feature called Virtual Host. Activating this feature turns your NVR into a “host” for the cameras allowing you to connect to them via a browser. Essentially, the NVR forwards all traffic received from your browser to the appropriate camera you’re trying to connect to, eliminating the biggest problem of plug and play functionality.
.

Step 1:

First of all, access your NVR via a web browser. If you do not know the LAN IP of your NVR, download Hikvision’s tool SADP tool, which scans your network for any Hikvision devices that are connected and allow you to see and change their network settings, including the IP address.

Download SADP for Windows

Download SADP for MacOS

Step 2:

Once you’ve logged in, navigate to:

Configuration → System → Camera Management

This screen displays all the connected cameras on your NVR. Notice that the final column labelled “Connect” is currently empty. We’ll be coming back here in a moment.

Step 3:

Now, navigate to:

Network → Advanced Settings → Other

Turn on the Enable Virtual Host option.

Note – Your NVR will reboot when you click “Save”.

Step 4:

Now, navigate back to the Camera Management window from earlier. You’ll notice that the previously empty connect tab now features links for each camera currently connected to your NVR.

Step 5:

Click on any of these links to access the respective camera via your web browser:

That’s it, you’re done!

This should be useful when you want to access options on your camera that your NVR doesn’t feature. If you have any further questions feel free to ask, we’re happy to help.

Herospeed Firmware Software Download

admin — Sun, 07 Apr 2024 09:10:49 +0000

Herospeed Firmware Software Download, Herospeed Technology is a high-tech company specialized in software development, software customization and software implementation. It owns a group of long-term professionals who are engaged in software development and software customization. With strong technical development strength, Herospeed Technology fully meets customer needs.

Herospeed Firmware Software Download

NVR

The Network Video Recoder support network video access,and it has adopted a number of advanced IT technologies,such as audio/video codec technology(h.264,h.265,h.264+,h.265+),embedded system technology,storage technology, network technology and intelligent technologies.It can work independently as NVR,or as a powerful security networking system.

Channels	Version Info	Time	Download Url
4CH	NVR_HI3798_4CH	2019-10-15 16:38:28	.
9CH	N3009_32NR_ALH1P4_V2.0.4.230818_R2	2023-09-04 10:58:41
	N3009_32NR_ALH1P0A0_V2.0.4.230818_R1	2023-09-04 10:56:26
	N3009_32NR_BVH1P0A0_V2.0.4.230803_R2	2023-08-16 16:59:54
	N3009_32NR_BVH1P4_V2.0.4.230727_R2	2023-08-16 16:57:41
	NVR_SS621Q_9CH_4POE_PNP_BD_V5_update_V22.1.26.4	2022-10-17 19:43:14
	NVR_SS621Q_9CH_BD_V5_update_V22.1.27.5	2022-10-17 19:41:44
	HI3536E_H265_9CH_BD_V5_update_V21.1.26.5.zip	2021-07-30 15:00:45
	NVR_HI3536D_H265_9CH_8POE_PNP_BD_V5_V21.1.22.6	2021-06-19 15:02:53
	NVR_HI3536D_H265_9CH_BD_V5_V21.1.23.3	2021-06-19 14:59:40
	HI3536D_H265_9CH_4POE_PNP_BD_V5_V21.1.23.3	2021-06-19 14:28:10
	NVR_MC6830_9CH_4POE_PNP_BD_V5_update_KITS_V20.1.43.5	2021-01-14 10:17:01
	NVR_MC6830_9CH_AL_V5_update_V20.1.47.3	2021-01-06 10:12:45
	NVR_HI3536D_H265_2G_8POE_BD	2020-03-03 10:06:06
	NVR_HI3536D_H265_9CH_4POE_PNP_BD	2020-02-24 09:22:24
	NVR_HI3536D_H265_2G_9CH_BD	2020-01-17 14:36:47
	NVR_HI3798_9CH	2019-10-15 16:39:12
	NVR_HI3536D_H265_36D08.216.8POE.V8.1.19.1	2018-07-27 11:18:27
	NVR_HI3536D_H265_36D04.216.4POE.V8.1.19.1	2018-07-27 11:16:51
16CH	N3016_32NR_ALH1P8_V2.0.4.230817_R4	2023-09-04 11:14:03
	N3016_32NR_ALH1P0A0_V2.0.4.230818_R3	2023-09-04 11:04:52
	N3216_32NR_BVH2P16A4_V2.0.4.230721_R3	2023-08-16 17:29:52
	N3216_32NR_BVH2P0A4_V2.0.4.230802_R2	2023-08-16 17:22:10
	N3016_32NR_BVH1P0A0_V2.0.4.230802_R2	2023-08-16 16:54:08
	N3016_32NR_BVH1P8_V2.0.4.230727_R3	2023-08-16 14:30:32
	NVR_MC6830_16CH_16POE_PNP_HP_BD_V5_update_V22.1.24.5	2022-10-17 20:09:02
	NVR_MC6830_16CH_16POE_PNP_BD_V5_update_V22.1.24.5	2022-10-17 20:03:14
	NVR_SS621Q_16CH_8POE_PNP_BD_V5_update_V22.1.27.5	2022-10-17 19:59:39
	NVR_SS621Q_16CH_BD_V5_update_V22.1.27.5	2022-10-17 19:55:35
	NVR_HI3536C_H265_16CH_4POE_PNP3_BD_V5_update_V21.1.21.2	2021-06-28 11:36:50
	NVR_HI3536D_H265_16CH_BD_V5_V21.1.22.6	2021-06-19 16:04:04
	NVR_HI3536C_H265_16CH_8POE_PNP3_BD_V5_update_V21.1.20.4	2021-05-29 14:11:50
	NVR_MC6830_16CH_AL_V5_update_V20.1.47.3	2021-01-06 10:18:25
	NVR_HI3536C_H265_16CH_8POE_PNP3_BD_KITS	2020-07-14 13:40:02
	NVR_HI3536C_H265_16CH_4POE_PNP3_BD_KITS	2020-07-14 10:34:15
	NVR_HI3536C_H265_16CH_8POE_PNP3_BD_V5_KITS	2020-07-14 10:18:00
	NVR_HI3536C_H265_16CH_4POE_PNP3_BD_V5_KITS	2020-07-14 10:08:26
	NVR_HI3536C_H265_16CH_8POE_BD	2020-03-06 09:02:22
	NVR_HI3536C_H265_16CH_4POE_PNP3_BD	2020-01-17 15:08:08
	NVR_HI3536C_H265_16CH_8POE_PNP3_BD	2020-01-17 14:55:20
	NVR_HI3536D_H.265_4G_16CH_BD	2019-12-27 15:17:16
	NVR_HI3536C_H265_16CH_BD	2019-11-07 16:34:41
	NVR_HI3798_16CH	2019-10-15 16:39:52
	NVR_HI3536C_H265_16CH_8POE_PNP2_BD	2019-09-16 13:50:50
	NVR_HI3536C_H265_36C08.8POE.PNP.V8.1.26.2	2018-07-27 11:44:56
	NVR_HI3536C_H265_36C16.V8.1.15.2	2018-07-27 11:34:20
25CH	NVR_MC6830_25CH_BD_V5_update_V22.1.25.1	2022-10-17 20:12:14
	HI3536C_H265_25CH_16POE_PNP2_BD_V5_update_V22.1.24.5	2022-07-05 20:26:15
	NVR_MC6830_25CH_16POE_PNP_BD_V5_update_V22.1.2.2.zip	2022-04-18 11:42:09
	NVR_MC6830_25CH_16POE_PNP_HP_BD_V5_update_V22.1.1.2	2022-02-15 18:00:12
	NVR_HI3536C_H265_25CH_16POE_PNP3_BD_V5_update_V21.1.21.6	2021-06-01 16:56:24
	NVR_HI3536C_H265_25CH_BD_V5_update_V21.1.21.2	2021-05-29 14:26:37
	NVR_HI3536C_H265_25CH_16POE_PNP2_BD	2020-04-20 17:06:06
	NVR_HI3536C_H265_25CH_BD	2020-01-17 15:20:17
	NVR_HI3536C_H265_25CH_16POE_PNP3_BD	2019-12-19 19:06:55
	NVR_HI3536C_H265_36C16.16POE.PNP.V8.1.27.3	2018-07-27 13:38:36
	NVR_HI3536C_H265_36C25.V8.1.15.2	2018-07-27 13:33:58
32CH	N3332_32NR_ALH2P0A4_V2.0.4.230825_R2	2023-09-04 10:49:14
	N3332_32NR_ALH2P16A4_V2.0.4.230825_R2	2023-09-04 10:47:17
	N3332_32NR_BVH2P16A4_V2.0.4.230825_R10	2023-09-04 10:37:09
	N3332_32NR_BVH4P0A16_V2.0.4.230725_R4	2023-08-24 09:38:54
	N3332_32NR_BVH4P24A16_V2.0.4.230731_R4	2023-08-24 09:35:48
	N3332_32NR_BVH2P0A4_V2.0.4.230815_R7	2023-08-23 14:07:20
36CH	HI3536_H265_36CH_BD_V5_update_V21.1.24.6	2021-07-30 15:27:09
	NVR_HI3536_H265_36CH_X1_BD_V5_V20.1.37.6	2020-09-12 17:27:23
	NVR_HI3536_H265_36CH_BD	2020-02-21 16:45:09
	NVR_HI3536_H265_36CH_X1_BD	2019-09-16 15:30:50
	NVR_HI3536_36_V8.1.20.5	2018-07-27 13:47:16
64CH	N3664_32NR_BVH8P16A16_V2.0.4.230810_R3	2023-08-24 09:24:33
	N3664_32NR_BVH8P0A16_V2.0.4.230811_R9	2023-08-24 09:22:14
	HI3536_H265_64CH_BD_V5_update_V22.1.22.1	2022-10-17 20:15:51
	NVR_HI3536_H265_64CH_BD	2020-03-13 15:45:58
	NVR_HI3536_64_V9.1.13.5	2019-04-13 15:11:55

NOVATEK IP Camera

The NT IP Camera has adopted embedded system and a number of advanced IT technologies,such as audio/video codec technology(h.264,h.265,h.264+,h.265+),and integrated code compression, two-way audio intercom.

NOVATEK IP Camera

Resolution	Type	Firmware	Time	Download Url
2MP	AI	KF2_1ND_BVHB_V1.0.3.230926_R1	2023-10-23 13:46:17
5MP	AI	KL5_1ND_BVHB_V2.0.11.231012_R2	2023-10-23 13:49:17
8MP	AI	KL8_1ND_BVHB_V2.0.8.230925_R1	2023-10-09 16:31:55

Rockchip IP Camera

The RK IP Camera has adopted embedded system and a number of advanced IT technologies,such as audio/video codec technology(h.264,h.265,h.264+,h.265+),and integrated code compression, two-way audio intercom, intelligent analysis , PTZ,HDR, lens control, alarm input and output, buffer storage and network transmission and other functions.

Rockchip IP Camera

Resolution	Type	Firmware	Time	Download Url
2MP	AI	RV1109_IMX307_BASE_W_23.1.41.4	2023-10-23 14:40:30
2MP	AI	RV1109_IMX307NAND_BASE_W_23.1.06.2	2023-02-21 11:42:23
5MP	AI	RV1109_IMX335NAND_BASE_W_23.1.42.2	2023-10-23 14:47:41
5MP	AI	RV1109_IMX335_BASE_W_23.1.39.1	2023-10-09 14:02:51
8MP	AI	RV1126_IMX415_BASE_W_23.1.39.3	2023-10-09 14:05:07
4MP	AI	RP4_8E_BTHB_V2.0.5.230925_R1	2023-10-09 14:10:53

Fullhan IP Camera

The Fullhan High-definition network camera has adopted embedded system and a number of advanced IT technologies,which integrated code compression, two-way audio intercom, intelligent analysis , PTZ, lens control, alarm input and output, buffer storage and network transmission and other functions.

Fullhan IP Camera

Resolution	Type	Firmware	Time	Download Url
2MP	Normal	FH8852_F23_B1T0A1M0C0P1_W_21.1.26.6	2021-07-07 10:10:27
		FH8852_IMX307_B1T0A1M0C0P1_W_20.1.51.3	2021-02-06 16:46:23
		FH8852_F23_B1T0A1M0C0P2_W_20.1.27.4	2021-02-06 16:44:14
		FH8852_IMX307_B1T0A1M0C0P2_W_20.1.29.3	2020-08-07 19:19:34
		FH8830_F22_W_8.1.11.5	2020-06-04 15:43:29
	AI	FG2_16NR_BVHB_V2.0.7.231117_R1	2023-12-28 16:39:35
	WIFIIPC	HFG2_16NR_BVHB_V2.0.2.230927_R1	2023-10-23 13:56:29
3MP	FISHEYE	FH8830_AR0330_FISHEYE_W_9.1.15.4	2020-06-04 15:46:30
3MP	FISHEYE	FH8830_AR0330_FISHEYE_BD_W_9.1.2.1	2020-06-04 15:43:43
4MP	Normal	FH8856_IMX335_B1T0A1M0C0P1_W_21.1.26.4	2021-07-07 10:13:08
	Normal	FH8856_IMX335_B1T0A1M0C0P2_W_20.1.27.3	2020-08-07 16:50:26
	AI	FG4_16NR_BVHB_V2.0.3.231102_R1	2023-12-28 16:43:41
	WIFIIPC	FW4_16NR_BVHB_V2.0.2.230927_R1	2023-10-23 13:57:13
5MP	Normal	FH8856_K05_B1T0A1M0C0P1_W_21.1.26.1	2021-07-07 10:15:45
	SD	FH8856_K05_B1T1A1M0C0P1_W_21.1.26.1	2021-07-07 10:16:03
	WIFIIPC_SD	FH8856_K05_W1T1A1M0C0P1_W_21.1.51.1	2022-01-20 17:58:46
	WIFIIPC_SD	FH8856_K05_W1T1A1M0C0P2_W_20.1.28.2	2020-08-07 16:14:08

GK IP Camera

GK IP Camera uses an embedded system and a number of advanced IT technologies, such as audio and video encoding and decoding technologies (h.264, h.265, h.265+, H264+), integrated encoding and compression, supporting audio noise reduction, and response cancellation, Support humanoid detection, support full Netcom function, can realize plug-and-play access to the back-end.

GK IP Camera

Resolution	Type	Firmware	Time	Download Url
2MP	AI	GC2_16NR_ALHB_V2.0.4.230831_R2	2023-10-23 14:01:31
2MP	AI	GC2_8NR_ALHB_V1.0.2.211028_R2	2021-11-12 17:00:50
3MP	AI	GS3_8NR_ALHB_V1.0.1.211028_R2	2021-11-12 17:01:23
4MP	AI	GC4_16NR_ALHB_V1.0.2.220926_R1	2023-02-21 17:51:22
4MP	AI	GC4_8NR_ALHB_V1.0.0.211009_R5	2021-11-12 17:03:27
5MP	AI	GL5_16NR_ALHB_V2.0.3.230714_R2	2023-08-05 17:32:48

XVR

The Embedded Hybrid Digital Video Recorder is compatible with HDTVI,AHD and other coaxial HD specification,which can be accessed to any HDTVI,CVI,AHD,analog and network signal.It can disable numbers of analog channels and convert them to IP channels,which have both functions of DVR and NVR.

XVR

Channels	Version Info	Time	Download Url
4CH	XVR_MC6630_2830_4_BD_V5_updateV22.1.23.5	2022-10-17 20:26:06
	XVR_MC6630_2830_4_BD_4G_V5_updateV22.1.24.5	2022-10-17 20:21:08
	XF5004_16FH_BVH1B4_V1.0.1.220311_R2	2022-09-29 15:41:26
	XVR_3521D_6158_4_BD_V5_updateV22.1.9.4.zip	2022-04-18 14:11:54
	SDI_DVR_3521D_334S_4_BD_updateV21.1.31.3	2021-09-10 09:40:45
	X2104_16TP_BVH1B4_V1.0.0.210901_R4	2021-09-08 10:18:15
	XVR_3520DV400_6158C_4_BD_2G_V5_updateV21.1.26.6	2021-07-30 17:13:31
	XVR_3520DV400_6158C_4_BD_4G_V5_updateV21.1.27.4	2021-07-30 17:10:26
	XVR_3520DV400_6158C_4_BD_V5_updateV21.1.26.1	2021-07-30 17:01:58
	XVR_MC6630_2830_4_AL_V5_updateV20.1.48.2	2021-01-06 16:33:09
	XVR_MC6630_2830_4_AL_4G_V5_updateV20.1.48.5	2021-01-06 16:28:16
	XVR_3531D_6158_4_BD_V	2020-05-21 14:10:48
	XVR_3520DV400_6158C_4_BD_4G_V	2020-05-07 10:10:24
	XVR_3520DV400_6158C_4_BD_V	2020-04-09 17:22:06
	XVR_3521D_6158_4CH_BD_V	2020-04-07 10:47:07
	XVR_3520DV400_6158C_4_BD_2G	2019-08-16 09:00:44
	XVR_3520DV200_6134C_4_v	2019-03-08 15:05:02
	XVR_3520DV400_6158_4_BD_V	2019-02-28 14:07:49
	XVR_3520DV200_6134C_4_BD_V	2019-01-30 16:31:38
	XVR_3521D_6158_SMARTKITS_4_BD_V	2019-01-09 14:09:24
	XVR_3520DV200_6134C_SMARTKITS_4_BD_V	2019-01-09 10:29:13
	XVR_HI3520DV200_4_V	2018-10-25 15:53:28
	XVR_3520DV200_4_v	2018-06-14 20:16:43
	XVR_3531D_6158_4_v	2018-06-14 20:06:20
	SDI_DVR_3521A_334S_4_v	2018-04-23 18:39:49
	XVR_3521D_6158_4_v	2018-04-23 18:35:38
	XVR_3520DV300_2826_4_v	2018-04-23 18:24:39
	XVR_3521A_2826_4_v	2018-04-23 18:04:09
	XVR_HI3521A_4_v	2017-10-26 16:05:50
8CH	XF5008_16FH_BVH1B8_V1.0.1.220317_R3	2022-09-29 15:13:00
	XVR_3521D_6158C_8_BD_V5_updateV22.1.9.4.zip	2022-04-18 14:34:30
	XVR_3531D_6158_8_BD_V5_updateV22.1.11.2.zip	2022-04-18 14:26:48
	XVR_MC6630_2830_8_BD_V5_updateV22.1.6.6.zip	2022-04-18 14:16:19
	SDI_DVR_3531D_334S_8_BD_updateV21.1.31.3	2021-09-10 09:33:34
	X2108_16TP_BVH1B8_V1.0.1.210827_R2	2021-09-08 10:25:22
	XVR_3520DV400_6158C_8_BD_V5_updateV21.1.26.1	2021-08-02 10:12:23
	XVR_MC6630_2830_8_AL_V5_updateV20.1.48.2	2021-01-06 16:37:17
	XVR_3520DV400_6158C_8_BD_V	2020-04-30 15:39:08
	XVR_3531D_6158_8_BD_V	2020-04-20 16:07:30
	XVR_3521D_6158C_8_BD_V	2020-04-07 10:41:55
	XVR_3521D_6158_8_BD_V	2019-03-11 14:07:43
	XVR_3520DV300_6134C_8_v	2019-03-08 15:05:49
	XVR_3520DV400_6134C_8_BD_V	2019-03-01 09:10:08
	XVR_3531DCAS_6158_16_8_BD_V	2019-01-29 15:11:55
	XVR_3531DCAS_6158_8_BD_V	2019-01-19 15:00:33
	XVR_HI3531A_8_v	2018-07-03 09:31:45
	XVR_3521D_6158_8_v	2018-06-15 08:42:00
	XVR_3520DV300_8_v	2018-06-14 19:56:18
	SDI_DVR_3531A_334S_8_v	2018-04-23 19:04:14
	XVR_3531D_6158_8_v	2018-04-23 19:02:21
	XVR_3521A_2826_8_v	2018-04-23 18:55:07
	XVR_3531A_2826_8_v	2018-04-23 18:48:12
	XVR_HI3520DV300_8_v	2018-02-09 16:14:20
16CH	XF5016_16FH_BVH2B16_V1.0.1.220424_R6	2022-09-29 15:33:45
	XF5016_16FH_BVH1B16_V1.0.1.220317_R4	2022-09-29 15:22:05
	XVR_3521D_6158C_16_BD_V5_updateV22.1.14.5.zip	2022-04-18 14:52:24
	XVR_3531D_6158C_16_2_BD_V5_updateV22.1.9.4.zip	2022-04-18 14:48:27
	XVR_3531D_6158C_16_BD_V5_updateV22.1.12.1.zip	2022-04-18 14:45:29
	XVR_3531DCAS_6158_16_BD_V5_updateV22.1.12.3.zip	2022-04-18 14:41:41
	SDI_DVR_3531DCAS_334S_16_BD_updateV21.1.31.3	2021-09-10 09:38:48
	X2116_16TP_BVH2B16_V1.0.1.210827_R2	2021-09-08 10:37:23
	X2116_16TP_BVH1B16_V1.0.1.210827_R2	2021-09-08 10:30:05
	XVR_3531DCAS_6158_16_BD_V	2020-05-21 08:51:20
	XVR_3531D_6158C_16CH_2_BD_V	2020-04-20 19:19:14
	XVR_3531D_6158C_16_BD_V	2020-04-20 19:15:57
	XVR_3521D_6158C_16_BD_V	2020-04-07 10:44:06
	XVR_3531D_6158C_16_BD_X1_V	2019-09-23 16:57:22
	XVR_3521D_6134C_16_BD_V	2019-03-15 13:39:18
	XVR_3531D_6158_16_BD_V	2019-01-19 14:57:17
	XVR_3531A_2826_16_v	2018-09-17 17:15:07
	XVR_3521D_6134C_16_v	2018-07-27 11:05:18
	XVR_3521A_16_v	2018-07-16 15:38:04
	XVR_3531D_6158_16_v	2018-06-15 08:43:36
	XVR_HI3521A_16_v	2018-06-15 08:34:06
32CH	XVR_3531DCAS_6158_32_BD_V	2019-04-24 15:10:29
	XVR_3531D_6134C_32_BD_V	2019-01-30 09:46:04
	XVR_3531A_2816_32_v	2018-04-23 19:15:13
	XVR_HI3531A_32_v	2018-02-09 16:53:32

PC Client

VMS is an application platform software that can be used with embedded network monitoring equipment.It supports monitoring equipment by Onvif network protocol, integrated preview, video, playback, backup, PTZ control, alarm management and other functions,to provide flexible and diverse deployment programs, can be widely used in finance, public security, military, transportation, education and other fields of security projects.

PC Client

Channels	Version Info	Time	Download Url
iVMS810(MAC)	iVMS810_Mac-B1130.1.0.2.zip	2023-11-06 15:25:31
iVMS810(Windows)	iVMS810_Win64-B1130.1.0.2.230925	2023-11-06 15:01:15
iVMS320(Windows)	iVMS320_Windows_V23.1.3.230831_R2	2023-09-20 09:42:00
iVMS320(Mac)	iVMS320_Mac_V22.1.5.221027_R4	2022-11-01 12:42:35
iVMS330(Windows)	iVMS330_20.2.42.5_Setup	2020-10-23 13:51:04
VMSLite (Windows)	VMSLite Setup8.2.44.2	2019-04-11 10:53:25
VMS (Windows)	VMS Setup8.2.29.6	2018-07-20 09:50:49
VMSLite (Mac)	VMSLite for Mac8.2.29.6	2018-07-19 15:31:29

Wifi kits

The wifi nvr kits developed from 100W to 400W HD quality,and adopted audio/video codec technology,embedded system technology,storage technology,network technology,etc.It matches to wireless wifi,WIFI connection supports 2.4G and 5.8G band,plug and play.It is suitable for various scenes,which can connect several cameras to realize omnidirectional non-dead angle monitoring

Wifi kits

Resolution	Type	Firmware	Time	Download Url
1MP	4CH	NVR_WIFIHI3520D2G_4_V8.1.29.1	2020-06-04 15:59:40
	4CH	3518EV200_OV9732_W_WIFIKITS_8.1.5.4	2020-06-04 15:59:21
	9CH	NVR_HIWIFI3520D2G_9_V8.1.33.5	2020-06-04 15:59:03
	9CH	3518EV200_OV9732_W_WIFIKITS_8.1.5.4	2020-06-04 15:58:34
2MP	4CH	3518EV300_SP2309_W3T0A0M0C0P0_W_21.1.5.2	2021-02-24 15:07:53
		NVR_WIFIHI3520D2G_4_V8.1.29.1	2020-06-04 16:02:47
		3518EV200_IMX323_WIFIKITS_W_8.1.3.5	2020-06-04 16:02:25
		NVR_WIFI3536D2G_SW01_4_V8.1.32.2	2020-06-04 16:02:09
		3516EV100_F23_W30T0A0M0C0_W_8.1.29.2	2020-06-04 16:01:50
		3516EV100_F23_W30T0A2M0C0_W_8.1.29.2	2020-06-04 16:01:32
		3516EV100_F23_W30T0A0M4C0_W_8.1.29.2	2020-06-04 16:01:13
		3516EV100_F23_W30T0A0M3C0_W_8.1.29.2	2020-06-04 16:00:55
		NVR_WIFI3536D2G_SW01_BD_4_V9.1.1.4	2020-06-04 16:00:39
	9CH	FH8852V200W_JXF23_W3T0A0M0C0P0_W_21.1.9.1	2021-03-10 14:11:00
		3518EV300_SP2309_W3T0A0M0C0P0_W_21.1.5.2	2021-02-24 15:08:32
		NVR_SS621Q_9CH_WIFI_SW03_BD_V5_update_V21.1.6.4	2021-02-06 19:43:34
		NVR_HIWIFI3520D2G_9_V8.1.33.5	2020-06-04 16:05:18
		3518EV200_IMX323_WIFIKITS_W_8.1.3.5	2020-06-04 16:04:59
		NVR_WIFI3536D2G_HW01_8_V8.1.21.1	2020-06-04 16:04:41
		3516EV100_F23_W30T0A0M0C0_W_8.1.29.2	2020-06-04 16:04:20
		3516EV100_F23_W30T0A2M0C0_W_8.1.29.2	2020-06-04 16:04:05
		3516EV100_F23_W30T0A0M3C0_W_8.1.29.2	2020-06-04 16:03:46
		3516EV100_F23_W30T0A0M4C0_W_8.1.29.2	2020-06-04 16:03:32
		NVR_WIFI3536D2G_HW01_BD_9_V9.1.1.4	2020-06-04 16:03:11
4MP	4CH	NVR_WIFI3536D2G_SW01_4_V8.1.32.2	2020-06-04 16:05:58
	4CH	3516D_OV4689_W_WIFIKITS_8.1.20.4	2020-06-04 16:05:37
	9CH	NVR_HIWIFI3798_9_V7.1.38.2	2020-06-04 16:09:01
		3516D_OV4689_W_WIFIKITS_8.1.20.4	2020-06-04 16:06:45
		NVR_WIFI3536D2G_HW01_8_V8.1.21.1	2020-06-04 16:06:27
5MP	4CH	FH8856V500W_JXK05_W3T0A0M0C0P0_W_21.1.9.1	2021-03-10 14:52:05
		NVR_SS621Q_4CH_WIFI_SW03_BD_V5_update_V21.1.6.4	2021-03-10 14:50:25
		NVR_WIFI3536D2G_HW01_4_V8.1.38.5	2020-06-04 16:11:58
		3516D_OS05A10_W30T0A1M0C1_W_8.1.38.3	2020-06-04 16:11:28
		NVR_WIFI3536D2G_HW01_BD_4_V9.1.1.4	2020-06-04 16:11:08
		NVR_WIFI3536D2G_SW01_BD_4_V9.1.1.4	2020-06-04 16:10:41
8MP	4CH	FH88568_JXK05_W3T0A0M0C0P0_W_21.1.9.1	2021-03-10 14:43:37
8MP	4CH	NVR_SS621Q_4CH_WIFI_SW03_BD_V5_update_V21.1.6.4	2021-02-06 17:52:14

SigmaStar IP Camera

The SigmaStar IP Camera has adopted embedded system and a number of advanced IT technologies,such as audio/video codec technology(h.264,h.265,h.264+,h.265+),and integrated code compression, two-way audio intercom, intelligent analysis , PTZ, lens control

SigmaStar IP Camera

Resolution	Type	Firmware	Time	Download Url
2MP	AI	SSC336Q_SC200AI_W_22.1.06.2	2022-04-02 10:18:59
5MP	AI	SSC338Q_SC500AI_W_22.1.43.1	2023-02-21 17:40:43
8MP	AF	SSC338Q_SC8238_W_22.1.45.4	2023-02-21 17:33:13
8MP	WH	SSC338Q_SC500AI4K_W_23.1.28.5	2023-08-05 17:39:53

Hisilicon IP Camera

The Hisilicon High-definition network camera has adopted embedded system and a number of advanced IT technologies,such as audio/video codec technology(h.264,h.265,h.264+,h.265+),and integrated code compression, two-way audio intercom, intelligent analysis , PTZ, lens control, alarm input and output, buffer storage and network transmission and other functions.

Hisilicon IP Camera

Resolution	Type	Firmware	Time	Download Url
1MP	Normal	3518EV200_OV9732_W_8.1.30.5	2020-06-04 13:48:46
1.3MP	Normal	3518EV200_IMX225_W_7.1.34.5	2020-06-04 13:49:26
1.3MP	Normal	3518EV200_S3130_W_7.1.25.1	2020-06-04 13:49:05
2MP	Normal	3516EV200_IMX307_B1T0A1M0C0P1_W_20.1.33.1	2021-02-06 16:07:09
		3516EV200_F23_B1T0A1M0C0P1_W_20.1.33.1	2021-02-06 16:02:03
		3516CV500_IMX307_B1T0A1M0C0P1_W_20.1.28.2	2020-08-07 19:06:19
		3516CV500_IMX462_B1T0A1M0C0P1_W_20.1.29.2	2020-08-07 15:32:07
		3518EV200_IMX323_W_7.1.25.1	2020-06-04 14:13:38
		3516CV200_OV2718_W_7.1.26.4	2020-06-04 14:13:20
		3516CV300_IMX290_W_8.1.9.3	2020-06-04 14:13:02
		3516CV200_IMX323_W_7.1.25.2	2020-06-04 14:12:39
		3516D_IMX290_W_7.1.32.3	2020-06-04 14:08:48
		3516CV300_IMX323_W_8.1.9.3	2020-06-04 14:08:20
		3516CV300_IMX323_B1T0A1M0C1_W_9.1.5.2	2020-06-04 14:01:32
		3516CV300_IMX307_B1T0A1M0C1_W_9.1.5.1	2020-06-04 14:01:04
		3516CV300_IMX327_B1T0A1M0C1_W_9.1.9.5	2020-06-04 14:00:43
		3516EV100_F23_B1T0A1M0C1_W_9.1.12.2	2020-06-04 14:00:15
		3516CV300_IMX307_B1T0A1M0C1P1_W_20.1.3.2	2020-06-04 13:59:51
		3516CV300_IMX323_B1T0A1M0C1P1_W_9.1.1.6	2020-06-04 13:56:16
		3516CV300_IMX327_B1T0A1M0C1P1_W_20.1.2.3	2020-06-04 13:55:57
		3516EV100_F23_B1T0A1M0C1P1_W_9.1.1.6	2020-06-04 13:55:39
		3516EV200_SP2309_B1T0A1M0C0P1_W_9.1.26.2	2020-06-04 13:52:12
	SD	3516CV500_IMX462_B1T1A2M1C2P1_W_20.1.32.5	2021-02-06 16:09:31
		3516EV200_IMX307_B1T1A1M0C0P1_W_20.1.33.1	2021-02-06 16:07:35
		3516CV500_IMX307_B1T1A2M1C2P1_W_20.1.33.4	2021-02-06 16:02:50
		3516EV200_F23_B1T1A1M0C0P1_W_20.1.33.1	2021-02-06 16:01:26
		3516CV500_IMX307_B1T1A1M0C0P1_W_20.1.28.2	2020-08-07 19:04:42
		3516CV500_IMX462_B1T1A1M0C0P1_W_20.1.29.2	2020-08-07 15:31:19
		3516CV300_IMX323_TF_W_8.1.6.6	2020-06-04 14:24:33
		3516CV300_IMX290_TF_W_8.1.6.6	2020-06-04 14:24:10
		3516CV300_IMX323_B1T1A1M0C1_W_9.1.5.2	2020-06-04 14:23:51
		3516CV300_IMX323_B2T1A1M0C1_W_9.1.5.2	2020-06-04 14:23:32
		3516CV300_IMX307_B1T1A1M0C1_W_9.1.5.1	2020-06-04 14:23:15
		3516CV300_IMX307_B2T1A1M0C1_W_9.1.5.1	2020-06-04 14:22:58
		3516CV300_IMX327_B2T1A1M0C1_W_9.1.9.5	2020-06-04 14:22:09
		3516CV300_IMX327_B1T1A1M0C1_W_9.1.9.5	2020-06-04 14:21:51
		3516CV300_IMX307_B1T1A1M0C1P1_W_20.1.3.2	2020-06-04 14:21:17
		3516CV300_IMX307_B2T1A1M0C1P1_W_20.1.3.2	2020-06-04 14:20:56
		3516CV300_IMX323_B1T1A1M0C1P1_W_9.1.1.6	2020-06-04 14:20:33
		3516CV300_IMX323_B2T1A1M0C1P1_W_9.1.1.6	2020-06-04 14:20:08
		3516CV300_IMX327_B1T1A1M0C1P1_W_20.1.2.3	2020-06-04 14:16:38
		3516CV300_IMX327_B2T1A1M0C1P1_W_20.1.2.3	2020-06-04 14:16:17
		3516EV200_SP2309_B1T1A1M0C0P1_W_9.1.26.2	2020-06-04 14:15:56
	SL	3516CV300_IMX290_W_SL_8.1.15.3	2020-06-04 14:25:12
	MINI	3516CV500_IMX307_MINI_WIFI_BD_W_20.1.28.2	2020-08-07 19:04:03
		3516CV500_IMX307_MINI_BD_W_20.1.28.2	2020-08-07 16:06:01
		3516CV300_IMX290_MINI_W_7.1.48.2	2020-06-04 14:26:25
		3516D_IMX290_W_MINI_7.1.27.3	2020-06-04 14:26:07
		3516CV300_IMX307_MINI_BD_W_20.1.16.4	2020-06-04 14:25:51
	PTZ	3516EV200_IMX307_X10T1A1M0C0P1_W_20.1.33.3	2021-02-06 16:59:48
		3516CV500_IMX462_X10T1A1M0C0P1_W_20.1.33.4	2021-02-06 16:59:02
		3516CV500_IMX307_X10T1A1M0C0P2_W_20.1.25.4	2020-08-07 19:03:37
		3516CV500_IMX307_X10T1A1M0C0P1_W_20.1.28.2	2020-08-07 19:03:13
		3516CV300_IMX290_AF_5X_W_8.1.10.1	2020-06-04 14:35:52
		3516CV300_IMX323_AF_5X_W_8.1.9.3	2020-06-04 14:35:35
		3516CV300_IMX290_AF_5X485_W_7.1.36.4	2020-06-04 14:35:12
		3516CV300_IMX323_AF_5X485_W_7.1.37.2	2020-06-04 14:33:56
		3516CV300_IMX323_X10T0A1M0C1_W_9.1.8.2	2020-06-04 14:32:57
		3516CV300_IMX323_X10T1A1M0C1_W_9.1.8.2	2020-06-04 14:32:38
		3516CV300_IMX323_X11T1A1M0C1_W_9.1.8.2	2020-06-04 14:32:21
		3516CV300_IMX307_X10T0A1M0C1_W_9.1.7.1	2020-06-04 14:32:01
		3516CV300_IMX307_X10T1A1M0C1_W_W_9.1.7.1	2020-06-04 14:31:18
		3516CV300_IMX307_X11T1A1M0C1_W_9.1.7.1	2020-06-04 14:31:00
		3516CV300_IMX327_X10T0A1M0C1_W_9.1.11.1	2020-06-04 14:30:40
		3516CV300_IMX327_X10T1A1M0C1_W_9.1.11.1	2020-06-04 14:30:20
		3516CV300_IMX327_X11T1A1M0C1_W_9.1.11.1	2020-06-04 14:30:00
		3516CV300_IMX307_X10T0A1M0C1P1_W_20.1.3.2	2020-06-04 14:29:42
3516CV300_IMX307_X10T1A1M0C1P1_W_20.1.3.2		2020-06-04 14:29:22
3516CV300_IMX307_X11T1A1M0C1P1_W_20.1.3.2		2020-06-04 14:29:04
3516CV300_IMX323_X10T0A1M0C1P1_W_9.1.1.6		2020-06-04 14:28:44
3516CV300_IMX323_X10T1A1M0C1P1_W_9.1.1.6		2020-06-04 14:28:25
3516CV300_IMX323_X11T1A1M0C1P1_W_9.1.1.6		2020-06-04 14:28:05
3516CV300_IMX327_X10T0A1M0C1P1_W_20.1.2.3		2020-06-04 14:27:43
3516CV300_IMX327_X10T1A1M0C1P1_W_20.1.2.3		2020-06-04 14:27:28
3516CV300_IMX327_X11T1A1M0C1P1_W_20.1.2.3		2020-06-04 14:27:13
WIFI IPC_SD	3516CV300_IMX323_W_WIFIIPC_SD_8.1.5.5	2020-06-04 14:36:43
	3516CV300_IMX323_W1T1A1M0C1_W_9.1.8.2	2020-06-04 14:36:28
	3516CV300_IMX323_W1T1A1M0C1P1_W_20.1.16.4	2020-06-04 14:36:13
GUARD	3516CV300_IMX327_GUARD_BD_W_9.1.1.6	2020-06-04 14:37:06
AI	3516CV500_IMX307_AR_EM_AF_BD_W_21.1.3.5	2021-02-06 17:05:11
	3516CV500_IMX307_AR_EM_BASE_BD_W_20.1.52.2	2021-01-20 10:56:02
	3516CV500_IMX327_AR_EM_BASE_BD_W_21.1.2.6	2021-01-20 10:54:38
	3516CV500_IMX327_AD_BASE_BD_W_9.1.27.2	2020-06-04 14:40:21
	3516CV500_IMX327_AR_BASE_BD_W_9.1.27.5	2020-06-04 14:40:05
	3516CV500_IMX327_AR_AF_BD_W_9.1.34.4	2020-06-04 14:39:46
3MP	Normal	3516D_IMX123_W_8.1.10.3	2020-06-04 14:41:10
4MP	Normal	3516D_OV4689_W_7.1.35.4	2020-06-04 14:41:42
	SD	3516D_OV4689_W_SD_8.1.32.3	2020-06-04 14:42:29
	SD	3516D_OV4689_W_SD_S_8.1.6.2	2020-06-04 14:42:10
	BOX	3516D_OV4689_W_BOX_7.1.49.3	2020-06-04 14:43:06
	PTZ	3516D_OV4689_5NEWPTZ_W_SD_8.1.24.1	2020-06-04 14:47:40
	PTZ	3516D_OV4689_5NEWPTZ485_W_SD_8.1.15.2	2020-06-04 14:47:25
	WIFIIPC_SD	3516D_OV4689_W_WIFIIPC_SD_8.1.12.3	2020-06-04 14:48:04
	FISHEYE	3516D_IMX326_FISHEYE_MAX_W	2019-04-03 09:29:20
		3516D_IMX326_FISHEYE_BD_W	2019-01-09 10:52:17
		3516D_IMX326_FISHEYE_W	2017-10-20 16:50:24
	MINI	3516DV300_IMX335_MINI_WIFI_BD_W_20.1.33.6	2021-02-06 16:53:02
5MP	Normal	3516DV200_IMX335_B1T0A1M0C0P1_W_20.1.47.6	2021-02-06 16:04:48
		3516A_IMX178_W_8.1.11.6	2020-06-04 15:17:23
		3516D_OS05A10_B1T0A1M0C1_W_9.1.12.5	2020-06-04 15:17:06
		3516D_OS05A10_B1T0A1M0C1P1_W_9.1.53.1	2020-06-04 15:16:48
		3516D_IMX335_B1T0A1M0C1P1_W_9.1.52.2	2020-06-04 15:16:29
	SD	3516DV200_IMX335_B1T1A1M0C0P1_W_20.1.47.6	2021-02-06 16:05:08
		3516DV200_IMX335_B1T1A2M1C2P1_W_20.1.48.1	2021-02-06 16:03:56
		3516D_OS05A10_B1T1A1M0C1_W_9.1.12.5	2020-06-04 15:20:56
		3516D_OS05A10_B2T1A1M0C1_W_9.1.12.5	2020-06-04 15:19:46
		3516D_OS05A10_B1T1A1M0C1P1_W_9.1.53.1	2020-06-04 15:19:25
		3516D_OS05A10_B2T1A1M0C1P1_W_9.1.53.1	2020-06-04 15:18:44
		3516D_IMX335_B1T1A1M0C1P1_W_9.1.52.2	2020-06-04 15:17:53
	BOX	3516D_OS05A10_BOX_W_9.1.12.3	2020-06-04 15:21:40
	BOX	3516D_OS05A10_BOX_BD_W_9.1.1.6	2020-06-04 15:21:25
	PTZ	3516DV200_IMX335_X80T1A2M1C0P1_W_21.1.5.7	2021-02-22 14:30:06
		3516DV200_IMX335_X10T1A1M0C0P1_W_20.1.47.6	2021-02-06 16:55:14
		3516D_OS05A10_X10T0A1M0C1_W_9.1.12.5	2020-06-04 14:45:44
		3516D_OS05A10_X10T1A1M0C1_W_9.1.12.5	2020-06-04 14:45:22
		3516D_OS05A10_X11T1A1M0C1_W_9.1.12.5	2020-06-04 14:44:54
		3516D_OS05A10_X10T0A1M0C1P1_W_9.1.53.1	2020-06-04 14:44:40
		3516D_OS05A10_X10T1A1M0C1P1_W_9.1.53.1	2020-06-04 14:44:24
		3516D_OS05A10_X11T1A1M0C1P1_W_9.1.53.1	2020-06-04 14:44:02
		3516D_IMX335_X10T0A1M0C1P1_W_9.1.52.2	2020-06-04 14:43:45
		3516D_IMX335_X10T1A1M0C1P1_W_9.1.52.2	2020-06-04 14:43:30
	WIFIIPC_SD	3516D_OS05A10_W1T1A1M0C1_W_9.1.12.4	2020-06-04 15:23:01
		3516D_OS05A10_W2T1A1M0C1_W_9.1.12.4	2020-06-04 15:22:42
		3516D_OS05A10_W1T1A1M0C1P1_W_9.1.1.6	2020-06-04 15:22:26
		3516D_OS05A10_W2T1A1M0C1P1_W_9.1.1.6	2020-06-04 15:22:08
	AI	3516DV300_IMX335_AR_EM_BASE_BD_W_21.1.13.5	2021-04-12 11:04:03
		3516DV300_IMX335_AR_EM_AF_BD_W_21.1.11.2	2021-04-12 11:03:32
		3516DV300_IMX335_AR_BASE_BD_W_9.1.27.5	2020-06-04 15:15:17
		3516DV300_IMX335_AR_AF_BD_W_9.1.35.2	2020-06-04 15:15:03
6MP	SD	3516aV200_IMX326_W_8.1.2.2	2020-06-04 15:24:02
6MP	PTZ	3516AV200_IMX326_AF4X_AUDIO_TF_W_8.1.13.1	2020-06-04 15:25:34
8MP	Normal	3516AV300_IMX415_B1T0A1M0C0P1_W_20.1.35.3	2021-02-06 15:54:48
	Normal	3516AV300_IMX415_B1T0A1M0C0P2_W_20.1.26.2	2020-08-07 18:55:00
	SD	3516AV200_OS08A10_B1T1A1M0C0P1_W_20.1.33.5	2021-02-06 15:56:08
		3516AV300_IMX415_B1T1A2M1C0P1_W_20.1.35.3	2021-02-06 15:55:20
		3516AV300_IMX415_B1T1A2M1C0P2_W_20.1.26.2	2020-08-07 18:55:52
		3519V100_IMX274_W_7.1.39.3	2020-06-04 15:26:35
		3516AV200_IMX274_W_9.1.16.3	2020-06-04 15:26:21
		3516AV200_IMX274_B1T1A1M0C0P1_W_20.1.13.3	2020-06-04 15:25:51
	PTZ	3516AV300_IMX415_X10T1A2M1C0P1_W_20.1.32.5	2021-02-06 19:18:15
		3516AV200_OS08A10_X70T1A2M1C1P1_W_20.1.35.3	2021-02-06 16:56:56
		3516AV200_IMX274_AF4X_AUDIO_TF_W_8.1.15.2	2020-06-04 15:27:21
	WIFIIPC_SD	3516AV200_OS08A10_W2T1A1M0C1P1_W_9.1.1.5	2020-06-04 15:27:44
	AI	3516AV300_IMX415_AR_EM_BD_W_21.1.12.4	2021-04-12 11:04:46
12MP	SD	3519V101_IMX226_B1T1A1M0C0P1_W_20.1.13.2	2020-06-04 15:28:08
	BOX	3519V101_IMX226_BOX_BD_W_9.1.1.6	2020-06-04 15:28:22
	PTZ	3519V101_IMX226_X70T1A2M1C1P1_W_20.1.13.2	2020-06-04 15:28:37
	FISHEYE	3519V101_IMX226_FISHEYE_W_9.1.16.1	2020-06-04 15:36:22
	FISHEYE	3519V101_IMX226_FISHEYE_BD_W_9.1.46.3	2020-06-04 15:30:04

Ambarella IP Camera

The AmbarellaHigh-definition network camera has adopted embedded system and a number of advanced IT technologies,which integrated code compression, two-way audio intercom, intelligent analysis , PTZ, lens control, alarm input and output, buffer storage and network transmission and other functions.

Ambarella IP Camera

Resolution	Type	Firmware	Time	Download Url
2MP	Normal	s2l33m_imx322_W_7.1.25.1	2020-06-04 15:39:53
3MP	Normal	s2l55m_imx123_W_7.1.25.2	2020-06-04 15:40:25
4MP	Normal	S2L55M_OV4689_W_7.1.18.3	2020-06-04 15:42:54
6MP	FISHEYE	S2E66_IMX178_W_7.1.3.4	2020-06-04 15:43:12

Tools

The Search Tool is a tool for searching online devices.The software can search the local area network with all the online devices,and can display the device relevant information.The Search Tool can also be used to modify the device’s network parameters individually or in batch,upgrade device individually,and modify the device password in batch.

Tools

Tool name	Version Info	Time	Download Url
Search Tool(Windows)	SearchTool for WIN_V1.5.3.231115_R1	2023-12-13 14:22:03
Search Tool(Mac)	SearchTool for MacOS_1.3.0.220121_R2	2022-01-24 14:54:13
TestTool(Windows)	TestTool_v2.0.3.6906	2020-07-08 15:01:38
IPWizardIII(Windows)	IPWizardIII_2.2.5	2018-11-07 16:38:30

Manual

The manual provides documents such as the Quick Start Guide for electronic files, User Manuals, and Installation Guide for each product, making it easy to understand each product in a simple or comprehensive way!

Manual

Class	Title	Language	Type	Time	Download Url
IPC	IP PTZ web6.0 User Manual	English	pdf	2022-11-24 19:03:12
	IP Camera Quick Start Guide Web6.0	English	pdf	2022-10-20 11:35:14
	IP Camera Web6.0 User Manual	English	pdf	2022-06-27 19:12:28
	Wi-Fi IP Camera Quick Start Guide Ali	English	pdf	2020-07-13 11:28:52
	Smart IP Camera Quick Start Guide Ali	English	pdf	2020-07-13 11:28:17
	IP Camera Quick Start Guide Ali	English	pdf	2020-07-13 11:27:47
	Wi-Fi IP Camera Quick Start Guide 350	English	pdf	2020-07-13 11:11:09
	Smart IP Camera Quick Start Guide 350	English	pdf	2020-07-13 11:10:39
	IP Camera Quick Start Guide 350	English	pdf	2020-07-13 11:10:01
	Dual Smart IP Camera Quick Start Guide BD	English	pdf	2020-07-13 11:00:58
	Camera Quick Installation Guide（Split Type）	English	pdf	2019-09-30 15:37:20
	IP Camera Quick Start Guide CK	English	pdf	2019-08-15 13:35:42
	Wi-Fi IP Camera Quick Start Guide BD	English	pdf	2019-07-12 10:18:00
	Smart IP Camera Quick Start Guide BD	English	pdf	2019-05-14 16:48:50
	IP Camera Quick Start Guide BD	English	pdf	2018-09-21 08:33:56
	Camera Quick Installation Guide	English	pdf	2018-06-19 16:11:51
	WiFi IP Camera Quick Start Guide	English	pdf	2018-06-19 16:11:38
	IP Camera User Manual	English	pdf	2018-06-19 16:11:19
	IP Camera Quick Start Guide	English	pdf	2018-06-19 09:25:31
NVR	NVR Quick Start Guide_6.0.pdf	English	pdf	2023-08-04 14:16:26
	NVR User Manual_6.0	English	pdf	2022-10-20 10:18:03
	NVR Quick Start Guide BD 6.0	English	pdf	2022-10-20 10:17:26
	NVR Quick Start Guide BV_5.0	English	pdf	2020-08-03 16:20:12
	NVR Quick Start Guide Ali_5.0	English	pdf	2020-08-03 16:19:40
	NVR Quick Start Guide 350_5.0	English	pdf	2020-08-03 16:18:41
	NVR User Manual_5.0	English	pdf	2020-05-28 13:34:56
	NVR Quick Start Guide BD_5.0	English	pdf	2020-04-09 16:26:42
	Wi-Fi NVR Quick Start Guide BD	English	pdf	2019-10-18 14:04:24
	Smart NVR Quick Start Guide BD	English	pdf	2019-07-09 17:00:34
	NVR Quick Start Guide BD	English	pdf	2018-09-03 09:02:14
	NVR User Manual	English	pdf	2018-06-19 16:12:58
	NVR Quick Start Guide	English	pdf	2018-06-19 09:32:18
XVR	XVR User Manual_5.0	English	pdf	2020-11-11 17:47:54
	XVR Quick Start Guide BV_5.0	English	pdf	2020-08-03 16:32:42
	XVR Quick Start Guide 350_5.0	English	pdf	2020-08-03 16:31:59
	XVR Quick Start Guide Ali_5.0	English	pdf	2020-08-03 16:31:34
	XVR Quick Start Guide BD_5.0	English	pdf	2020-06-09 17:16:09
	Smart XVR Quick Start Guide	English	pdf	2019-09-03 08:39:55
	XVR Quick Start Guide BD	English	pdf	2018-09-04 16:11:40
	XVR Quick Start Guide	English	pdf	2018-06-19 16:26:52
	XVR User Manual	English	pdf	2018-06-19 16:26:30
EX-SDI&HD-SDI DVR	EX-SDI&HD-SDI DVR User Manual	English	pdf	2018-12-21 08:28:55
	EX-SDI&HD-SDI DVR Quick Start Guide BD	English	pdf	2018-09-03 09:07:57
	EX-SDI&HD-SDI DVR Quick Start Guide	English	pdf	2018-07-11 10:15:48
PLC Kits	PLC Kits Quick Start Guide	English	pdf	2018-06-19 16:30:26
PoE Kits	PoE Camera Security System Quick Start Guide	English	pdf	2023-09-27 14:20:55
	PoE Kits Quick Start Guide BD	English	pdf	2020-07-17 16:47:43
	PoE Kits Quick Start Guide BD 5.0	English	pdf	2020-07-17 16:29:19
WiFi Kits	Wi-Fi Camera Security System Quick Start Guide.pdf	English	pdf	2023-08-04 14:26:10
	Wi-Fi Kits Quick Start Guide BD PGE	English	pdf	2022-02-14 16:18:53
	Wi-Fi Kits Quick Start Guide BD 5.0	English	pdf	2021-03-30 10:25:27
	Wi-Fi Kits Quick Start Guide BD	English	pdf	2021-03-17 14:29:38
	Non-economical Wi-Fi Kits Quick Start Guide BD	English	pdf	2019-07-11 16:28:04
	Economy Wi-Fi Kits Quick Start Guide BD	English	pdf	2019-07-11 16:26:58
	Smart Wi-Fi Kits Quick Start Guide	English	pdf	2018-09-03 08:40:56
	Smart Wi-Fi Kits Quick Start Guide BD	English	pdf	2018-08-24 09:40:43
	Economy WiFi Kits Quick Start Guide	English	pdf	2018-06-19 16:37:07
	Non-economical WiFi Kits Quick Start Guide	English	pdf	2018-06-19 16:36:55
XVR Kits	XVR Kits Quick Start Guide BD 5.0	English	pdf	2020-07-17 16:27:25
	XVR Kits Quick Start Guide BD	English	pdf	2019-01-07 17:10:53
	Smart XVR Kits Quick Start Guide BD	English	pdf	2018-08-24 09:41:18
	XVR Kits Quick Start Guide	English	pdf	2018-06-19 16:40:16
	Smart XVR Kits Quick Start Guide	English	pdf	2018-06-19 16:40:02
Consumer WiFi Camera	LCY4B LongPlus Quick Start Guide	English	pdf	2022-06-23 16:09:43
	LCY4A LongPlus Quick Start Guide	English	pdf	2022-06-23 16:08:49
	LTP4F LongPlus Quick Start Guide	English	pdf	2022-03-28 18:06:34
	LongPlus Quick Start Guide	English	pdf	2021-03-17 14:26:03
	Consumer Fisheye Camera P3 Quick Start Guide	English	pdf	2018-06-19 16:40:37
PoE Switch	RT2418 Managed Optical Fiber PoE Switch User Manual	English	pdf	2021-07-15 13:51:11
	HT812(100M&1000M) HT811 HT412 HT1612 Series PoE Switch Quick Start Guide	English	pdf	2019-04-03 08:53:12
	RT2418 Managed Optical Fiber PoE Switch Quick Start Guide	English	pdf	2018-11-06 14:23:13
	24+2+2 Unmanaged Optical Fiber PoE Switch Quick Start Guide	English	pdf	2018-06-19 16:41:30
	24+2 Managed PoE Switch Quick Start Guide	English	pdf	2018-06-19 16:40:56
Search Tool	Search Tool User Manual for Win&Mac	English	pdf	2018-06-19 17:03:49
App	iVMS380 App User Manual	English	pdf	2020-11-09 14:52:33
	Aliluya App User Manual	English	pdf	2020-08-03 15:24:55
	iVMS350 App User Manual	English	pdf	2020-08-03 15:24:20
	ACESEE App User Manual	English	pdf	2019-09-02 10:10:19
	iVMS320 App User Manual	English	pdf	2019-01-16 09:59:10
	BitVision App User Manual	English	pdf	2018-12-20 17:21:30
	FreeIP App User Manual	English	pdf	2018-06-19 16:42:20
	VR Panorama App User Manual	English	pdf	2018-06-19 16:42:05
VMS	iVMS330 Plateform User Manual for windows	English	pdf	2020-11-09 15:06:16
	iVMS320 User Manual for Mac	English	pdf	2019-04-15 15:28:59
	iVMS320 Plateform User Manual for win	English	pdf	2019-04-15 15:28:02
	VMS User Manual for Mac	English	pdf	2018-06-19 16:48:21
	VMS User Manual for Win	English	pdf	2018-06-19 16:48:06
	VMS Lite User Manual for Mac	English	pdf	2018-06-19 16:45:35
	VMS Lite User Manual for Win	English	pdf	2018-06-19 16:45:24
Coaxial	Camera Quick Installation Guide(Split Type)	English	pdf	2019-11-01 15:35:23
Smart Device	AI Face Recognition Device Quick Start Guide 08GRW-EU QR	English	pdf	2021-10-09 09:23:13
	Intelligent Terminal Health code quick start guide 02	English	pdf	2021-09-28 09:33:20
	AI Face Recognition Device Quick Start Guide 08GRW	English	pdf	2021-08-03 10:13:44
	AI Face Recognition Device Quick Start Guide 08GR	English	pdf	2021-08-03 10:12:25
	AI Face Recognition Device User Manual	English	pdf	2021-07-16 10:50:34
	Smart Device 2000 Quick Start Guide 02GYWT	English	pdf	2021-04-20 14:51:30
	Smart Device 2000 Quick Start Guide 02GYT	English	pdf	2021-04-20 14:50:55
	Thermal Smart IP Camera Quick Start Guide BMMH256	English	pdf	2021-04-07 19:10:11
	Dual Smart IP Camera Quick Start Guide BD BMMH32	English	pdf	2021-04-07 19:08:54
	AI BOX Quick Start Guide 5.0	English	pdf	2021-03-30 10:35:09
	Thermal Smart IP Camera Quick Start Guide	English	pdf	2021-03-09 14:58:56
	AI Face Recognition Device Quick Start Guide 05GRW	English	pdf	2020-12-14 09:24:26
	AI Face Recognition Device Quick Start Guide 05GR	English	pdf	2020-12-12 14:45:36
	Thermal Smart IP Camera Quick Start Guide OWL256	English	pdf	2020-11-24 10:20:05
	Dual Smart IP Camera Quick Start Guide BD OWL32	English	pdf	2020-11-24 10:19:21
	Thermal Smart IP Camera User Manual	English	pdf	2020-11-04 09:13:13
	Thermal Smart IP Camera Quick Start Guide CMLDISS500T-256	English	pdf	2020-11-04 09:12:37
	Temperature Measuring Metal Detector Security Gate BD CMLDISS500T	English	pdf	2020-11-04 09:11:47
	Smart Device 2000 Quick Start Guide 03AY	English	pdf	2020-11-04 09:09:55
	Smart Device 2000 Quick Start Guide 03AYW	English	pdf	2020-08-03 15:13:17
	Smart Device 2000 Quick Start Guide 02GY	English	pdf	2020-08-03 15:11:47
	Smart Device 2000 Quick Start Guide 02GYW	English	pdf	2020-08-03 15:10:26
	Smart Device 2000 Quick Start Guide 02GYH	English	pdf	2020-08-03 15:08:36
Consumer Camera with Battery	IP Camera Quick Start Guide X86V1R4BR4A	English	pdf	2022-02-22 14:52:34
	IP Camera Quick Start Guide normal	English	pdf	2022-02-22 14:52:17
	Y2A(RX07)	English	pdf	2021-12-06 17:28:06
	R4B(X86)	English	pdf	2021-12-06 17:27:50
	R4A(V1)	English	pdf	2021-12-06 17:27:25
	R2B(V3)	English	pdf	2021-12-06 17:27:04
	R2A(X82)	English	pdf	2021-12-06 17:26:51
	Q2A(X85)	English	pdf	2021-12-06 17:26:28
	P4A(X87)	English	pdf	2021-12-06 17:26:11
	P2A(X81)	English	pdf	2021-12-06 17:25:40

BitVision

The BitVision client is an easy to use P2P network camera video monitoring professional mobile phone client software, connected by a sequence number, the only global P2P network and network cameras installed in the home or office, view real-time video images, and image capture, video. The scene situation users can learn in the shortest possible time home or office. P2P network camera of the software production and the company in the network of cooperation to normal use.

BitVision

Channels	Version Info	Time	Download Url
BitVision	BitVision_Android_V21.1.11	2021-10-12 14:45:19
	BitVision_Android_V21.1.9	2021-09-02 10:00:37
	BitVision_Android_V21.1.7	2021-07-16 08:54:29
	BitVision_Android_V20.1.46.1	2020-11-13 09:38:58

ACESEE

ACESEE is an application platform software that can be used with Smart wi-fi device, it is a service APP launched for families and businesses. Through ACESEE, you can easily check real-time and play-back videos of apartments, villas, shops, factories, offices and other places; through ACESEE ‘s alarm service, you can take safety protection at the first time once you receive abnormal information about the places you are concerned about. No matter where you are, your home and business are nearby always.

ACESEE

Channels	Version Info	Time	Download Url
ACESEE	ACESEE_Android_V1.0.41	2021-11-22 19:43:46
ACESEE	ACESEE_PC(Windows)_V1.0.0.10	2021-05-07 17:33:41

iVMS350

iVMS350 is an application platform software that can be used with Smart device。 Main function: 1:Remote-monitoring: View video via APP remotely, know what is going on anywhere and anytime; 2: Two way audio function: audio in and audio out; 3:Device sharing: Share the device with your family numbers, view together, 4:Motion detection Alarm: Alarm and picture capturing about abnormal situation, guard the security.

iVMS350

Channels	Version Info	Time	Download Url
iVMS350	IOT_iVMS350_Android_V21.1.05.3	2021-01-28 13:32:52
	IOT_iVMS350_Android_V20.1.41.4	2021-01-14 08:28:39
	IOT_iVMS350_Android_V20.1.39.1	2020-09-29 09:37:17
	IOT_iVMS350_Android_V20.1.36.4	2020-09-15 16:59:00

LongPlus

LongPlus is an application platform software that can be used with cloud device. Main function: 1:Remote-monitoring: View video via APP remotely, know what is going on anywhere and anytime; 2: Two way audio function: audio in and audio out; 3:Device sharing: Share the device with your family numbers, view together; 4:Cloud storage of timing video and alarm video.

LongPlus

Channels	Version Info	Time	Download Url
LongPlus	LongPlus_Android_V21.1.35	2021-10-14 20:36:07

IVS365

IVS365 is an application platform software that can beused with device module. Main function: 1:Remote-monitoring:View video with APP remotely,know what is going on any where and anytime; 2:Two way audio function:audio in and audio out; 3:Device sharing:Share the device with your family numbers,view together; 4:Motion detection Alarm:Alarm and picture capturing about abnormal situation,guard the security.

IVS365

Channels	Version Info	Time	Download Url
IVS365	IVS365_Android_1.0.0.211101_R6	2021-11-16 14:22:38
IVS365	IVS365_Android_1.0.0.210619_R3	2021-06-19 11:46:08

SDP2000

SDP2000 is an application platform software that can be used with smart terminal devices. It supports management devices through network protocols, integrates multiple functions such as device management, personnel management, access management, and report management. It provides flexible and diverse deployment solutions. The server can be connected to multiple intelligent terminal devices, manage multiple entrances and exits, and can be widely used in airports, entry and exit gates, train stations , government agencies, schools, scenic spots, large factories and other places that need to be identified to help customers achieve Efficient, safe and intelligent entrance and exit management

SDP2000

Channels	Version Info	Time	Download Url
SDP2000（Windows）	SDP2000_EN_x64_V2.6.3.220209_R2	2022-02-14 17:44:52

IVSEC X mobile app Full Guide

admin — Fri, 22 Mar 2024 21:15:40 +0000

IVSEC X mobile app Full Guide, IVSEC is a reliable distributor of security systems and products. IVSEC will help you find the best equipment for all your security needs, using security cameras, biometrics, and specialised software. IVSEC specialises in supplying reliable technology and equipment for home and workplace security solutions.

The IVSEC brand comprises Australian selected components and hardware, and software servers for local updates within Australia. IVSEC has grown quickly while expanding and maintaining excellent customer service. For any enquiries, please contact our friendly staff.

My smartphone is showing “offline” or “connect close” in the IVSEC X mobile app?

When adding your Recorder or cameras to the IVSEC X mobile app if a message says “Offline” or the device status is showing “Connect close” please check the following:

Example of Offline message

Example of Connect Close message

1) Check that the QR code, username and password details have been entered correctly into the IVSEC X app

A. Connect HDMI LCD and USB mouse to IVSEC Recorder

B. Click on the 4-square / arrow icon on the bottom left-hand corner of the screen

C. Check the name shown in Current user:

Note: The default user is admin but this may have been modified by the installer

D. Open the IVSEC X app on your phone

E. Press the “Human” icon of the top left-hand corner of the app

F. Press “Device List’

G. Press the square icon with a pencil mark

H. Check the IP Address/ID is the same as the QR code located on top of the IVSEC recorder

I. HTTP Port / Client Port

• To connect to an IVSEC Recorder use port 9000 or 80

• To connect to an IVSEC Camera that does not have a recorder installed use port 6000 or 80

J. Check the username is the same name as per point C (this is case sensitive)

K. Enter the correct password

L. Press Save or Apply

2) Check for Network Connectivity

A. Check that an ethernet cable is connected to the LAN port of your modem

B. Check that the other end of the ethernet cable is connected to the LAN/WAN port of the IVSEC Recorder

C. Check that the Green and Yellow LEDs light up after connecting the cable.

NOTE: If the LEDS do not light up then the IVSEC X app will not work. Try replacing the ethernet cable, if still no LEDS light up contact your installer

D. Connect an LCD and USB mouse to the recorder and check the “connect status” icon that appears on the bottom right hand corner of the taskbar (when LCD is connected to recorder). Ensure that the icon has a green tick as shown in below image

Refer to explanation below of other connection status:

3) Ensure you have the latest version of IVSEC X app installed on your phone. Check that your Android or Apple device has the latest software/firmware and security updates installed. Try un-installing, re-installing the app and add the device again

4) Power your modem and IVSEC Recorder off for 30 seconds. Power back on and wait 5 minutes for the internet connection to come back online.

5) If you are running a VPN app on your smartphone disable the app and try the IVSEC X app again.

Examples of VPN providers include Surfshark, NordVPN, Norton’s VPN.

6) Check the IVSEC Recorder substream settings

A. Using LCD and mouse connected to NVR go to setup – Record – Encode Check your NVR substream settings- “Substream” tab

Recommended substream settings to minimise mobile app bandwidth issue

Resolution: 640 x 480

Bitrate: 512kbps

B. Click Apply on bottom right corner

Please refer to YouTube link: Adjusting stream settings via IVSEC X Mobile app

Please refer to YouTube link: Adjusting Camera stream settings via NVR (LCD & mouse required)

7) Some older Samsung phones running Android 11 on the Telstra network may be unable to stream live view or the cameras will show as offline while connected to mobile data (4G/5G). The issue has been identified on the Telstra network where an Android update causes the APN to select IPv6 only. Click here for APN re-configuration (Applies to Telstra mobile customers only running Android)

8) Some Telstra NBN modem / routers may restrict access to cameras (firmware issue on the router). The cameras may be slow to appear or show as offline. Check the model number listed on the bottom of your Telstra router. Click on the documentation below which details the steps to configure port forwarding as a workaround to access your cameras

• Telstra Netgear V7610 – Click Here

• Telstra Technicolor DJA0231 – Click Here

9) Connect to your wifi and perform a speed test – https://www.speedtest.net/

Click the GO button. If your upload speed result is 3Mbps or less, you should contact your Internet Provider to test your connection

10) Email service@ivsecurity.com.au for additional support

iVSEC X Mobile App

1. How to set up the IVSEC X app on my Smartphone

The IVSEC X app allows you to access your IVSEC cameras live view remotely, playback recordings and other useful features
Please refer to YouTube link: https://youtu.be/71mvg5QdsfY

Scan the appropriate QR code below to download the IVSEC X app

Apple Store | Google Play

2. My smartphone is showing “connect close” in the IVSEC X mobile app?

Click here for troubleshooting details.

3. How to reduce camera buffering when accessing IVSEC cameras on the mobile app.

If you have limited or slow Internet connection (either at home or on your smartphone) reducing the substream settings can help the cameras to show up quicker on the app

Video guide – How to modify the settings via the IVSEC X mobile app

Video guide – How to modify the settings via the Recorder using an LCD and mouse

Recommended substream settings
Resolution: 640 x 480 | Bitrate: 256 kbps

Recommended mobile stream settings
Resolution: 640 x 480 | Bitrate: 128 kbps

4. What does “Max User Playback” mean?

If you see “Max User Playback” when trying to playback footage in the app it means someone else is currently accessing playback either via the NVR or through the app. Restarting the NVR will clear this message.

Access via Windows / Mac

5. How to install setup the VMS Pro application for Windows.

Video Guide

NOTE: VMS for Windows setup is similar for Mac

Application download links available from ivsecurity.com.au or via the YouTube description

6. How to login to an IVSEC NVR or camera using Internet Explorer or Chrome

Refer to “How to upgrade my NVR firmware” FAQs. Once your NVR is upgraded to the latest firmware you will be able to log in using any browser using the NVR IP address.

7. How can I search for IVSEC devices on a network or change an IP address

To search for X range cameras and recorders on a network use the Device Config Tool.

8. How to setup the surveillance client on Windows

Please note surveillance client is no longer supported, refer to VMS Pro. For legacy installations please refer to YouTube links below:

Windows | Mac

9. My MAC is not letting me install any of the IVSEC applications

If your MAC blocks the app from opening click here for details

10. How to playback and export footage from surveillance client on a Mac

Watch Video Guide

11. How to get my old IVSEC app working (non X range NVR model)

Check the model number of your recorder (silver sticker either on the top or bottom of the recorder. If the model number does NOT have an X in the model number then click here for instructions on how to configure your non X range IVSEC NVR using port forwarding and DDNS.

Recorder

17. How to configure disk grouping for 16, 32 and 64 channel IVSEC recorders

The maximum number of channels (cameras) that can record to one hard drive is 16. If your recorder is compatible with disk grouping (e.g. NR316XB, NR316XC, NR532XA, NR564XA, NR564EXA and NR564EXB) you will need to configure disk grouping and ensure your cameras are recording. If you are using an NVR that is capable of 64 channels and have 64 cameras installed, you will need to install a minimum of 4 hard drives

16 cameras installed = 1 hard drive required (minimum)

32 cameras installed = 2 hard drives required (minimum)

64 cameras installed = 4 hard drive required (minimum)

Video – Disk grouping setup process

IP Camera

18. How to factory reset my IVSEC camera?

Download IVSEC Camera Reset Procedure (specific models)

19. How to factory reset my IVSEC camera?

Download IVSEC Camera Reset Procedure (specific models)

20. How to Setup 3rd Party cameras onto an IVSEC X-Range NVR

Watch Video Guide
Download Device manager tool (for non X range IVSEC branded cameras)
Download IVSEC PTZ Search Tool (for non X range IVSEC branded cameras)
Hikvision camera setup using onvif
Dahua camera setup using onvif

21. How to add 2N IP Verso Intercom camera to an IVSEC NVR

Watch Video Guide

22. Camera image is randomly showing distortion on the bottom of the image

If you are experiencing distortion at the near the bottom of the camera image please click here for useful troubleshooting steps

23. Modifying White Light Settings

Some of the iVSEC camera range have inbuilt white lights (LEDs) that turn on at night as a deterrent to intruders and for colour recording at night. Please follow this guide to learn how to disable this function or have then turn on only when motion is detected.

Smart Home Integration

24. iVSEC – Alexa

Now it’s even easier to see what’s happening. Amazon Alexa can be used to stream live camera video to your Amazon Echo Spot or Echo Show device simply by speaking your commands. Follow this guide to learn how to connect to Amazon Alexa for voice control.

25. iVSEC – Google

Now it’s even easier to see what’s happening. You can ask your Google Assistant to show your Cameras on your TV with Chromecast. Read this guide to learn how to connect your cameras to your Google Assistant and enable voice control.

How to upgrade IVSEC NC323XD Camera Firmware For additional support go to https://ivsecurity.com.au/ or email service@ivsecurity.com.au Video will demonstrate how to upgrade IVSEC NC323XD camera firmware. NOTE: Firmware compatible with models NC323XD, NC531XB, NC512XC, NC512XD & NC528XC Download NC323XD firmware (link below) https://ivsecurity.com.au/support/fir… Copy the entire folder to USB flash drive Connect USB to NVR and watch video demonstrating how to perform the upgrade.

How to playback and export footage from surveillance client onto a MAC

How to playback and export footage from surveillance client onto a MAC To download Surveillance client and Device Config Tool (MAC) – https://www.dropbox.com/s/49enfbklip4… To download VLC for MAC – https://www.videolan.org/vlc/download… For more information visit https://ivsecurity.com.au/

RXCamView PC and Mobile Guide 2024

admin — Fri, 15 Mar 2024 20:14:17 +0000

RXCamView PC is a surveillance software, which support Apple Push Notification service, support live video stream, video record and playback, video remote playback, snapshots and PTZ control, etc. RXCamView for PC: Enhancing Your Experience with Surveillance with RXCamView for PC

Introduction

It’s never been simpler to ensure the security of your house or place of business in these age of modern technology. Because to its strong capabilities and easy-to-use interface, RXCamView is a popular smartphone application designed for controlling security cameras. Although the software is mostly meant to be used on mobile devices, a lot of customers want the ease of having their surveillance feeds accessible on PCs. We’ll go through the advantages of using RXCamView for PC in this blog article, along with a detailed setup tutorial.

Why Opt for RXCamView on a PC?

1. Increased Screen Space

The increased screen real estate that RXCamView on your PC provides is one of its main benefits. You may watch many video feeds at once and get a full picture of your surroundings with a computer display.

2. Improved Split-Minute

On your computer, you may effectively multitask by using RXCamView app. You may focus on other things, including office work, internet surfing, or running your company, while keeping an eye on your cameras at the same time.

3. Accurate Keyboard and Mouse Control

Using a keyboard and mouse makes navigating around your camera feeds and settings more straightforward. You can precisely access camera settings, pan, tilt, and zoom in real time, which improves your capacity to react to security incidents.

4. Robust Association

When compared to mobile devices, PCs often provide more reliable and continuous internet connections. This stability guarantees continuous access to your security cameras, which is essential for preserving your property’s security.

5. Numerous Storage Choices

Your storage options are more flexible on a PC. You may preserve important security recordings by storing video footage and images locally on the hard disc of your computer.

RX CamView Installation Instructions for Windows 10

Get RXCamView for Windows first before moving on to the installation procedure. Use a file compression programme like WinRAR or 7Zip to extract the RXCamView download once it has been downloaded for Windows and Mac OS.

Double-clicking the programme file will launch the installation procedure. Open the RXCamView for PC folder once the download file has been extracted.

Downloading and Installing RXCamView for PC

After discussing the advantages of using RXCamView on your computer, let’s go through how to set it up:

1. Set up an emulator for Android

To use RXCamView on Android and iOS devices, you must first install an Android emulator on your computer. LDPlayer, NoxPlayer, and BlueStacks are a few well-liked choices. Install any of these emulators that you’ve downloaded.

DOWNLOAD RXCAMVIEW

DOWNLOAD BLUESTACKS

2. Get RXCamView.

Launch the Android emulator, then go to the Google Play Store from inside it. Look for “RXCamView” and download the software.

3. Start RXCamView.

Open RXCamView from inside the emulator once it has been installed. If you don’t already have an RXCamView account, you’ll need to create one or log in.

4. Include Your Lenses

After selecting “Add by Device ID” or “Add by IP/Domain,” click the “Device” or “Add Device” icon. To add your cameras to the programme, provide the password, username, and unique ID of each camera.

5. Start Observing

Once your cameras have been installed, you may use your PC to monitor your company or property. You may examine recorded video, see live feeds, and adjust camera settings as necessary.

Features of RXCamView for PC windows 11/10/8/7 & Mac

We provide information so that you may get familiar with the capabilities and tasks that RXCamView for PC is capable of. You may download RXCamView for Windows 11/10 and Mac OS for free on your computer to connect the security camera.

The list of features that RXCamView for Windows OS has to offer is shown below.

• Watch real-time HD video.

• Watching videos from the past.

• Reminder message for the event.

• Make a two-way audio call.

• Receive immediate notifications when sound, motion, or human shape is detected.

• Adjust the sensitivity and detecting area.

• Schedule the alarm notification and recording times.

Further ways to Get RXCamView for PC

Step 1: RXCamView Installation for Windows 7/8/10

• The first window that appears on the screen during the programme installation process allows you to choose the software installation route. Click the “Browse” button to choose a folder location where you wish to install the software file, or click the “Next” button to leave everything as it is.

• Click the “Next” button to bring up a screen where a shortcut to the start menu may be created.

• Following that, a screen with two options will show up for you. “Create Desktop Icon” and “Quick Launch icon” are the first two. Press the “Next” button now.

• The installation will now start when the screen appears. Simply choose the “Install” option.

• The installation will now start while you wait for the procedure to finish.

• Simply choose the “Launch MaxxOne App for Windows/Mac OS” option on the screen when the installation is complete, then click the “Finish” button.

• Now launch the MaxxOne App for Windows or Mac OS, choose “Group Device Management,” and add devices to your programme.

Step 2: Add devices using the Windows/Mac OS MaxxOne app

• The device management screen will now show up; choose the device by clicking on it.

• Once the device management page appears, just choose “Import All.”

• Click the “Main Menu” choices to bring up the home screen.

Step 3: Use the Mac or Windows MaxxOne app to see live content.

This is where you can watch the MaxxOne app in real time on Mac or Windows.

Final Words on RXCamView PC

Managing and keeping an eye on your security cameras is made easier and more simple with RXCam View PC. With its bigger screen, improved multitasking, accurate keyboard and mouse handling, reliable internet connection, and more storage possibilities, it’s a great solution for consumers who want to improve their surveillance experience. You can get the most out of RX Cam View on your PC and have the piece of mind that comes from knowing your property is safe by following the easy setup instructions provided in this blog article.

FAQs

1. How to Connect RXCamView Cameras?

It’s easy to set up your cameras to work with RXCamView. Take these actions:

• Using the Google Play Store or Apple App Store, depending on your device, download and install the RXCamView app.

• Open the application and create an RXCamView account if you don’t already have one.

• Within the app, tap the “Add Device” or “+” icon.

• Input the necessary camera information, such as the IP address, login, and password.

• Make sure your mobile device and cameras are linked to the same local WiFi network.

• As soon as the information is accurately provided, the app should detect your camera and allow you to begin watching.

2. Why does my RXCamView says connect close?

If you get the “Connect Close” notice in RXCamView, there could be a connection issue with your camera. The following are some possible causes and remedies:

• Verify that your camera is connected correctly and check its power supply.

• Check to see whether your camera is linked to the neighbourhood wireless network.

• Verify that the login, password, and IP address you specified in RXCamView are accurate.

• Try reconnecting after restarting the RXCamView app and your camera.

3. In RXCamView, why am I seeing a “Username or Password Error”?

A “Username or Password Error” notification indicates that there is a problem with the login information you entered. Here’s how to deal with this issue:

Verify again the password and username you supplied in RXCamView for your camera. Make sure all the characters, capital or lowercase, are correct.
See your camera’s handbook or manufacturer’s documentation for instructions on how to reset the username and password if you can’t remember them.

4. How to Download RXCamView?

RXCamView is simple to download and may be found in the app store on your device:

Go to the Google Play Store on an Android smartphone and type “RXCamView.” In order to download and install the app, tap “Install”.
To find “RXCamView” for iOS devices, visit the Apple App Store. To download and install the app, tap “Get”.

5. How to connect RXCamview to iphone

The procedure for setting up RXCamView on your iPhone is the same as it is for Android devices:

• RXCamView may be downloaded and installed from the Apple App Store.

• If you do not already have an RXCamView account, create one now.

• Enter the IP address, username, & password of the camera to add it to the app.

• For the first setup, make sure that the iPhone and cameras are connected to the same Wi-Fi network.

6. How to connect RXCamView to WiFi?

The main step in setting up RXCamView for Wi-Fi is to confirm that your mobile device and cameras are connected to the same local Wi-Fi network. You will be required to provide the Wi-Fi network information for the camera when setting it up in the app. Depending on your settings, you may use RXCamView to access the camera remotely or through Wi-Fi after it’s joined to the network.

RxCamView App latest version for ios and Android (2024)

DOWNLOAD RXCAMVIEW APP

Follow these easy steps to utilize the RxCamView App Download:

“

Step 1: Obtaining and downloading the Android emulator
You must download and install an Android emulator before you can install the RxCamView App on your PC. BlueStacks and NoxPlayer are two common emulators. Visit the official websites of these emulators and download the setup file that is appropriate for the Windows or macOS version of your machine.

Step 2: Installing the Android emulator
Run the setup file when the download is finished and adhere to the on-screen directions to install the Android emulator on your computer. Depending on how fast your machine is, this procedure might take a while.

Step 3: Setting up the Android emulator
Launch the Android emulator after installation. You will be asked to sign in using your Google account during the first setup (or create one if you don’t already have one). To use the emulator’s Google Play Store, you must do this.

Step 4: Accessing the Google Play Store
You may use the Android emulator to visit the Google Play Store after logging into your Google account. Look for the Play Store icon in the app drawer or on the emulator’s home screen.

Step 5: getting the RxCamView app
Look for “RxCamView App” in the Google Play Store’s search box. Find the “Install” button for the RxCamView official app by searching for it. Automatic installation and download of the application will begin.

Step 6:Launching the RxCamView App
Find the RxCamView App icon on the home screen of the Android emulator or in the app drawer when the installation is finished. To open the RxCamView App, click the icon.

Step 7:Activating Your RxCamView Account
Use your registered email address and password to log into your RxCamView account to get to your RxCamView devices and settings. You may create a RxCamView account right from the app if you don’t already have one.

Step 8:Connecting Your RxCamView Devices
The RxCamView App will instantly sync with your RxCamView devices when you log in. The app’s device list will show any cameras, smart plugs, smart lamps, or sensors you may have. To link each device to your RxCamView account, follow the steps given by the app.

Step 9:Examining the RxCamView App
Congratulations! Using an Android emulator, you have successfully installed and configured the RxCamView App on your PC. Find out more about the app’s features, such as the live camera feeds, device settings, planning, automation, and event alerts.

“

RXCamview Setup With the Simplest

RXCamview Setup: Configuring RXCamView: Your Handbook for Stress-Free Monitoring.

Introduction

It’s easier than ever to make sure your house or place of business is secure in today’s ever changing environment. Technology breakthroughs have made it possible for surveillance systems like RXCamView to provide a handy method to keep an eye on your property from anywhere. This blog will show you how to set up RXCamView for seamless surveillance, whether you’re a company owner trying to protect your assets or a household wishing to increase your security.

Let’s begin with a quick overview of RXCamView before getting into the setup procedure. This adaptable and simple-to-use programme is designed for remote monitoring. With RXCamView, you can connect several IP cameras and use a computer or mobile device to monitor the live feeds, replay recorded video, and adjust different settings.

How does the RXcamView app operate?

As was already said, this programme makes it easy to monitor CCTV cameras. All you have to do is download it from the Google Play Store onto your phone. You’ll be able to monitor your house, place of employment, office, and more using this app. Making ensuring your gadget is properly linked to the internet is all that is required. All of your camera footage will be recorded here, which you may view at a later time.

You are able to capture every video on your mobile device using its replay capability. As a result, you may go on vacation or have a trip without being concerned that someone would break into your house without your knowledge. You can see anything that happens in your house from a distance as long as you have the app installed on your smartphone. You also have complete control over how you want to operate each camera in your house. This may ensure that you will eventually experience more convenience.

Other than this, you may download the app for free on your smartphone. It will provide you full live video here at no cost. This software lets you capture a picture and send it to security staff in case anything goes wrong with your cameras. Additionally, you may enlarge the picture using the app to see details better. All things considered, it’s a fantastic CCTV camera monitoring app.

How to use an emulator to download the RXCamview Setup for PC

This software works best not just on your PC but also on your Android mobile. However, in order for this programme to function properly on your computer, you must download an Android emulator. We’ll be using the Bluestacks Android app player in this instance. The actions that you ought to do are as follows:

1. On your Mac or PC, begin by downloading the Bluestacks emulator.

2. Launch the Bluestacks computer emulator.

3. The emulator’s home screen will display the Google Play Store.

4. Enter your Google login credentials and look for the RXcamView application.

5. Select the RXcamView app to download and install it on the Bluestacks emulator.

6. Open RXcamView on your computer and begin using it.

Prior to Starting: Requirements

A few items are required before you begin the setup process:

• Compatible Cameras: Verify that the IP cameras you have are compatible with RXCamView.

• Operating System: Make sure that RXCamView can be used on your PC (Windows or Mac) or mobile device (Android or iOS).

• Stable Internet Connection: In order to access and see your cameras remotely, you must have a stable internet connection.

How to Set Up RXCamView

First, let’s install the RXCamView application on the device of your choice. These are what to do:

Regarding Mobile Devices (iOS/Android):

• Launch the app store on your smartphone (iOS: Apple App Store; for Android, Google Play Store).

• Enter “RXCamView” into the search box of the app store.

• Choose the RXCamView app from the official store and press “Install” or “Download.”

• Open the app when the installation is finished.

Adding RXCamView Cameras

After installing RXCamView, it’s time to include your cameras. As follows:

• Launch the RXCamView application on your PC or mobile device.

• The “Add Device” or “Add Camera” option may be tapped or clicked.

• You will be required to provide the IP address, username, and password of the camera. Make sure you have this data at your disposal.

• Once the camera information has been entered, choose “Add” or “Save.”

• Your camera will be tried to be connected to by RXCamView. As soon as the connection is established, the live broadcast will appear on your screen.

Setting Up Camera Parameters

Try modifying your monitoring experience by going via the RXCamView options menu. The following settings are ones you may wish to change:

• Video Quality: Depending on your tastes and available bandwidth, you may adjust the video quality.

• Motion Detection: Set up the motion detection settings to get notifications whenever the camera detects movement inside its area of vision.

• Notifications: Configure alerts for your computer or mobile device to be notified when certain events happen.

Remote Observation and Access

The ability to remotely view your cameras is one of RXCamView’s main features. Activate remote access by:

• Make sure the internet is linked to your cameras.

• Access your RXCamView account using the programme or app.

• Choose the camera that you want to watch.

• Take advantage of live streaming and archived video from any location with an internet connection.

Troubleshooting Typical Problems

Although RXCamView is typically easy to set up, there are a few frequent problems that you may run into. Here are some pointers for troubleshooting:

In case your camera displays “offline,” make sure it is powered on or has an internet connection.

Try reinstalling the programme and making sure your device satisfies the system requirements if it fails.

Safeguard Advice

When it comes to surveillance systems, security is crucial. To ensure the security of your RXCamView configuration, follow these tips:

• Replace the default usernames and passwords with secure, one-of-a-kind ones.

• Update the firmware on your camera on a regular basis to guard against vulnerabilities.

Higher Level Features

Advanced capabilities like cloud storage and PTZ (Pan, Tilt, Zoom) control are available with RXCamView. To get the most out of your surveillance system, investigate these possibilities.

Combination with Different Devices Think about combining RXCamView with other smart home appliances, including voice assistants or smart hubs, for a fully connected experience.

Conclusion: RXCamview Setup

To sum up, RXCamView is a great option for anybody looking for a user-friendly surveillance system. You may improve your security and peace of mind by installing RXCamView for your home or place of business with the help of this tutorial. RXCamView is a useful addition to your security arsenal due to its flexibility and ease of use, regardless of your level of expertise.

RXCamView Alternative for Free

RXCamView Alternative: Investigating RXCamView Substitutes: Safeguard Your Area with These Best Monitoring Apps

Introduction

It is crucial to have a trustworthy surveillance system in place to protect your home or place of business. Even though RXCamView is a well-liked option, it’s a good idea to look at other possibilities as well in order to choose which one best meets your demands. We’ll present you to a few of the best RXCamView substitutes in this article, each with unique benefits and capabilities. There is a choice for everyone, regardless of their preferences for sophisticated features, price, or user-friendliness.

Top RXCamView Alternative Available

1. CloudEdge: Your Safe and User-Friendly Monitoring Solution

An effective and user-friendly substitute for RXCamView is CloudEdge. It gives you easy remote access to your cameras and delivers notifications in real time. Whether you’re at home or on the move, you can have peace of mind knowing that CloudEdge is monitoring your property from any location. The software is accessible to a broad spectrum of users since it is available for both iOS and Android smartphones.

2. Wyze: Feature-rich and reasonably priced surveillance

Wyze is a great option if you’re on a tight budget without sacrificing quality. Wyze provides a selection of reasonably priced cameras with outstanding features including two-way audio, 1080p resolution, and night vision. Because of its simple setup and remote watching capabilities, the Wyze app appeals to users on a budget.

3. Swann Security: Complete and Sturdy Monitoring Solutions

A reputable company, Swann Security is well-known for producing top-notch surveillance gear. They provide a variety of cameras, DVRs, and NVRs for home and business usage. The Swann Security app is a good substitute for people looking for a complete surveillance system as it lets you see and manage your cameras from a distance.

4. ARCCTV: Expert-Level Monitoring for Companies

For companies searching for top-notch surveillance solutions, ARCCTV is a great option. ARCCTV provides sophisticated features including analytics, support for multiple cameras, and cloud storage choices, with an emphasis on commercial and industrial applications. Its mobile app guarantees that company owners may easily keep an eye on their properties.

5. Lorex Home: State-of-the-Art Monitoring Systems

One of Lorex Home’s most notable features is its advanced surveillance equipment. They provide a large selection of cameras, including cordless and 4K Ultra HD versions. For individuals who need the newest in surveillance technology, the Lorex Home app is a fantastic substitute since it offers simple remote access and management.

6. EZView: Easy-to-use Monitoring for Everyone

Because EZView was created with simplicity in mind, it’s a great option for consumers looking for an easy setup. Features like motion detection, cloud storage, and live streaming are included in this RXCamView substitute. You may download the EZView app on both iOS and Android smartphones.

7. Geeni: Easy and Intelligent Surveillance Management

Geeni is a feature-rich monitoring application that is renowned for its use and simplicity. As it works with a large variety of Geeni smart cameras and gadgets, it’s a fantastic option for Geeni ecosystem enthusiasts. Geeni allows you to operate smart plugs and lamps, see live video feeds, and set up alarms for motion alerts all from inside the app.

8. Hue Widget: Hue Smart Lighting and Integrated Surveillance

The Hue Widget app is something to think about if your house is already equipped with Philips Hue smart lights. Your lighting system and surveillance are effortlessly integrated with this app. With the simplicity of smart lighting management, you can improve your home security by setting up alerts that are activated when your Hue cameras detect activity.

9. ImperiHome: The Complete Smart Home Monitoring Solution

An all-in-one smart home software called ImperiHome acts as a thorough control panel for a range of smart devices, including security cameras. As a result, you may integrate a variety of brands and gadgets into your smart home’s single interface. Because of its adaptability, ImperiHome is the best option for consumers who have a variety of smart home components.

10. HomeBrite: Easily Manage Your Smart Home Security System

The user-friendly software HomeBrite is designed to manage all the features of your smart home, including the security cameras. It ensures a flawless user experience by making smart device setup and administration simple. HomeBrite is accessible to both novices and seasoned smart home enthusiasts because to its user-friendly interface.

Final Words: RXCamView Alternative

RXCamView is only one app among many in the realm of security applications. Regardless of your needs—affordability, sophisticated functionality, or ease of use—there’s a substitute that can satisfy them. To choose the best surveillance software for you, take your time browsing through these selections, reading reviews, and thinking about your unique requirements. Because each of the options listed here has advantages of its own, you may feel safe about securing your area.

Ultimately, the decision boils down to what suits your house or place of business the best. To make an educated choice and experience the peace of mind that comes with efficient monitoring, consider your priorities, your budget, and the features you would want.

Note: Do your homework and make sure any surveillance programme or system you choose satisfies your unique needs, including compatibility with your cameras and devices. When choosing a solution, take privacy and data security into account as well.

RXCamView Android Latest Version

RXCamView Android: How to Use RXCamView on Android: A Comprehensive Guide to Streamlined Monitoring

About RXCamView Android

RXCamView is a trustworthy and adaptable security software designed specifically for Android smartphones at a time when technology breakthroughs are redefining how we safeguard our residences and commercial spaces. With a thorough grasp of RXCamView’s features and capabilities provided by this tutorial, you can be sure that your surveillance system is optimised to the fullest extent possible.

Using RXCamView: An Overview

To start downloading RXCamView, take your Android smartphone to the Google Play Store. Look for “RXCamView” online, then download and install the programme. It’s crucial to remember that RXCamView was created with Android users in mind, guaranteeing a flawless experience on the platform of your choice.

Establishing Your RXCamView Account: Setting up an RXCamView account is the next important step. Your entry point to remote surveillance is this account. You will be able to see your cameras with this account from any location with an internet connection. If you haven’t already, register, or just log in with your username if you already have.

Downloading and Installing and Running RXCamView Android

Setting Up and Adding Cameras:

Adding Cameras to RXCamView: After installing the app, open it to discover the camera choice. In order to integrate your surveillance equipment with the app, you must complete this step. For every camera, enter the required information, such as its login, password, and IP address. To ensure the success of this phase, make sure your cameras are linked to your local network.

Strategic Camera Positioning: Take into account the strategic positioning of your cameras for the best possible surveillance coverage. Pay particular attention to vulnerable spots, high-traffic areas, and entryways if you wish to increase security there. The efficiency of your surveillance system may be greatly impacted by the placement of your cameras.

Adjusting Camera Parameters: RXCamView Android gives you the ability to personalise your monitoring experience. You may adjust a number of things in the app’s settings menu, such as notification preferences, motion detection sensitivity, and video quality. Adjust these variables to meet your unique needs for monitoring.

Remote Observation and Access:

Remotely Accessing Cameras: RXCamView’s ability to provide remote access to cameras is its real strength. You only need to use the app to log into your RXCamView account once your cameras are online. This gives you the freedom to watch recorded video and live streams from any location with a reliable internet connection.

Troubleshooting Typical Problems:

Taking Care of Connectivity Problems: If a camera seems to be “offline,” you should look into its power supply and internet connection. Sustaining monitoring without interruption requires a steady connection.

App Stability: You should think about reinstalling RXCamView if you experience app crashes or instability. To guarantee seamless functioning, make sure your Android smartphone satisfies the required system requirements.

Examining Enhanced Functionality:

PTZ Control: Learn about PTZ (Pan, Tilt, Zoom) control to improve your surveillance skills. With the help of this function, you may precisely capture important details by being able to remotely change the camera’s field of view.

Cloud Storage: To safely store and access recorded video, think about putting cloud storage options into place. Convenience and redundancy are provided by cloud storage, while your sensitive data is protected.

Final Words: RXCamView Android

To sum up, RXCamView Android is a reliable way to improve your security and comfort. After reading through this extensive tutorial, you now have the understanding needed to install RXCamView on your Android smartphone and use it to its maximum capacity. You can confidently keep an eye on your surroundings whether you’re at home or out and about.

Make security a top priority by updating the firmware on your camera and changing the default passwords. You can ensure the best degree of security for your home or company by taking control of your surveillance with RXCamView on your Android mobile.

Start making the most of your surveillance skills right now, and enjoy the advantages of a smoothly functioning security system that gives you the ability to safeguard the things that are most important to you. You now have the power to ensure your safety, and RXCamView is leading the way.

RXCamview Login

RXCamView Login: A Comprehensive Guide to Safe Monitoring Access with the login process.

About RXCamview

With the help of RXCamView, you can see your security cameras from a distance. Its full potential can only be realised if you fully comprehend the login procedure. We’ll take you step-by-step through the RXCamView login process in this blog, making sure you can easily access your surveillance system and maintain the security of your property.

RXCamview Login The Entire Process:

Step 1: Get the app on your device

The RXCamView app must be installed on your selected device before you can log in. Whether it’s the Apple App shop for iOS users or the Google Play Store for Android users, you can get RXCamView from the app shop on your smartphone.

Step2: Open the application

Once the installation is finished, find the RXCamView app icon on the home screen of your smartphone and press it to open the programme.

Step 3: Create an Account (If Required)

To log in, you will need to establish an RXCamView account if you haven’t already. To create an account, click the “Sign Up” or “Register” button. You’ll be asked for some basic details, such your email address and a secure, one-of-a-kind password.

Step 4: Register

Go back to the app’s login page now that you have an account. This is the login process:

• Input the password you established while registering, along with your email address.

• Verify again that your login information is correct to prevent any access problems.

• Use a password manager to safely store and recover your password if you’re worried about forgetting it.

Step 5: Display at Home

Following a successful login, the RXCamView home screen will appear. You may access your linked cameras and other security features from here.

Step 6: Getting to Know Your Cameras

Press the camera icon or go to the camera list to see your cameras. This is where your RXCamView account’s cameras that you have added are shown. For a live stream, click on the camera you want to see.

Step 7: Observation through Remote

You may enjoy remote monitoring now that you are signed in and able to see your camera stream. With RXCamView, you can watch your property in real time from any location with an internet connection, giving you more protection and peace of mind.

Step 8: Extra Security Protocols

Consider putting the following precautions into practise to guarantee the maximum degree of security:

• Make sure your cameras’ default passwords are strong and distinctive.

• Update the firmware on your camera on a regular basis to guard against vulnerabilities.

• If available, enable two-factor authentication to provide an additional degree of protection.

Conclusion: RXCamview Login

To sum up, being proficient in the RXCamView login procedure is necessary for safe and practical access to surveillance footage. You may easily log into the app and use all of its features, including remote monitoring, by following these easy steps. RXCamView gives the power of surveillance in your hands, protecting your belongings and the people you care about, whether you’re at your place of residence or on the move.

By making security a top priority, you can improve the security of your house or place of business and experience the peace of mind that provides knowing you are in charge over your surveillance system.

How to Set Up SuperLive Plus

admin — Tue, 13 Feb 2024 18:09:51 +0000

How to Set Up SuperLive Plus, SuperLive Plus is a professional mobile phone client software for digital video recorders and IP cameras in CCTV surveillance (compatible models only). The software is for professional usage and copyright protected.

This is valid for our older 2MT-7XXX models and 2MT-7XXX-O models only.

First, you will need to download the application onto your phone and ensure that the DVR is connected to a network. We will focus on obtaining information from the DVR first before we focus on the phone app.

On the DVR, log into the menu, and then navigate to Setup → Network → NAT. Make sure that NAT is enabled (Note: you will not be able to access the cameras if NAT is not enabled).

Once NAT has been enabled, a QR code should appear. But if it does not, do not worry. The QR code can be found in a different section. If the QR code does not appear in NAT, it can be found in Information → QRCODE. If you are unable to scan the QR code for some reason, there will also be a serial number that will show below the QR code that you can input manually in order to connect your cameras to your phone.

Now that the QR code/serial number has been found we can focus on setting up the application. The first screen that you will see when you open the app is the Live View screen. From here, you can add a device by hitting the icon in the upper-right hand corner. This will open up the Server List.

Hit the Plus sign to add your device by either scanning the QR code or manually inputting the serial number that shows beneath the QR code. If you choose the QR code method, tap on the square icon and enable access to the phone’s camera. Then, the only other information that will need to be filled out is the name of the device (can be anything you would like for it to be), the username, and the password of the DVR.

Save the device, and go back to the Live View screen so that we can add your device to the Live View windows. There should be a drop down list underneath the windows that show your online devices. Just select the device, and the cameras should show on your screen.

How to setup my CCTV remote connection for viewing
on smartphones and tablets.

We have put together this guide for setting up a remote connection with our DVR’s so you can view your cameras from potentially anywhere in the world. We can also offer our Remote Setup Service where we can setup the system for you, this utilises port forwarding on your router and has the added ability to view your cameras from a Mac or PC.

We will need to set up the DVR firstly so that it is ready to accept the connection from your devices this can be done by the follow steps:

First and foremost connect the the DVR to your router either by an ethernet cable or, if running an ethernet cable is a problem, using a wireless extender which will allow your router to pick up the DVR or a Home Plug can also be used.

On the DVR click on the “Start” button in the bottom left corner of the screen and then choose “Settings” from the popup menu, if you can not click it or its greyed out login to the DVR and try again.

Then under Network click on the TCP/IP link.

On this page make sure there is a tick in the “Obtain an IPv4 address automatically” box and then click apply to save.

Once done, across the top of the page next go to Port and change the HTTP port and Server port to any 3-5 digit number but they need to be different from each other, then click apply to save.

Across the top again to UPnP and make sure there is a tick in the “Enable” box and that the map type is set to auto and click apply to save.

Across the top again to NAT and make sure there is a tick in the “Enable” box and click apply to save.

Leave this page open on your screen as we will be needing the serial number which you can see under the QR code or the QR code itself later in the guide.

We will now be covering the app side of the connection.

So on your phone or tablet go to your app store, either the Appstore on Apple or Play store on Android and search for an app called “SuperLive Plus”, it should look like the image below and install the app and agree to any permissions it asks for.

When first starting the app it will take you through several tutorial pages which you can either swipe through or tap on skip and you will then be presented with the option of local or start, tap on start.

You will now need to fill in the details for the connection: The serial number (which can be found on the NAT page which should still be displayed on your monitor). A nickname of your choosing the default being “DeviceName1” and Username/Password for the DVR. If you would like to bypass this stage tap on skip in the top right corner which will then take you to the Live page.

From here you can access other features or add multiple DVRs or connections if you have them by doing the following. Tap on the three little lines in the top left to bring up the options menu and choose Server List.

This page will list all of you connection entries, but at the moment there should be none. Tap on the “+” symbol in the top right and choose scan code and then scan the QR code on the DVR monitor screen, the information will be filled out for you for adding a device. You may still need to fill out the device name, user and password for the DVR and tap save.

Once saved it will take you back to the server list page and there should now be one entry. All things being well the little wifi icon on the entry should be a solid and green colour at which point you can tap on the back arrow (top left) to take you out and back to your live camera feeds. If the Wifi icon is a grey/black colour and searching then tap on the pen and paper icon to allow you to edit the information and make sure all information is correct re-typing the password for example is a common culprit as is auto correcting on the user and domain host and save to keep the settings.

Superlive Plus For PC: Free Download for windows 7/8/10/MAC

Here we are going to discuss SuperLive Plus for PC including window 7/8/10 and for MAC os as well. There are two methods by which you are able to take a good view of your CCTV cameras.

In this post, you can free download setup for Superlive plus for PC. After downloading the setup we will learn how to configure Superlive plus for PC.

SuperLive Plus For Windows PC

SuperLive Plus For MAC

Here we are going to use windows 7 and MAC but you can use the same setting for Windows 8 and Windows 10 as well. You can also use another application named “superlivepro for PC” So let’s start from the downloading the setup.

For the latest TVT DVRs and NVRs, a new app has been launched for remote monitoring. It is known as ‘NVMS Lite.’ Gradually, its updated versions are also introduced by the TVT Company. Here, we will learn to download and install the NVMS Lite 2.1 CMS App on Windows & Mac OS.

Download NVMS Lite 2.1 (Windows)

Download NVMS Lite 2.1 (Mac)

The NVMS Lite 2.1 CMS Software connects all TVT products seamlessly. Additionally, it also supports renowned manufacturer’s products like Hikvison, Dahua, Honeywell, etc.

Key Features & Functions of the NVMS Lite 2.1 CMS

Following are the key characteristics of it.

• It connects CCTV Cameras through QR codes, serial numbers or IP addresses. You can use any mode to add these cameras or recorders.

• The app gives you remote access. You can watch live at your locations from any place. There is no time lag.

• The CMS software supports the storage of data in the device or on the cloud server.

• You can watch the playback from your location. You can even take snaps and preserve recordings.

• You can operate devices with the help of the CMS App. You can pan, tilt or zoom them. You can even talk to them and exchange messages. You can also hear them from your remote place.

• It sends you alert signals from threats. The smart sensors detect motion and audio.

Download SuperLive Plus for Windows App to Monitor on Windows OS

The application file for Superlive plus for Windows CMS is shared here. The application is given in the below download button. Press the button to get the software. The complete installation process is defined below.

First you have to decompress the executable file and then download it. The complete installation part is demonstrated here step-by-step. It is shared in three parts. The first part denotes the installation of the app, the second step defines the sign-in process and the third step is reserved for the device addition.

Download NVMS Lite 2.1 (Windows)

Download SuperLive Plus for Mac CMS to Monitor on Macintosh PC

The company has provided the software for the SuperLive Plus for Mac CMS. It is given in the below download button. Click the button to get the executable file. Decompress them to install on your PC.

The installation to monitoring process are same as done for Windows OS.

Download NVMS Lite 2.1 (Mac)

Install SuperLive Plus for Android App to Monitor on Android Devices

The company keeps on updating its software for better user experience. It keeps on adding new features for safety and security. The SuperLive App is available for Android devices. The download link is given in the download button. Press it and get the link for your gadget.

Install SuperLive for Android

Install SuperLive Plus for iPhone App to Monitor on iOS

The SuperLive Plus App is given below. It is attached in a link button. You have to click the button to get the iOS software. After that, you can easily monitor your locations on Apple mobile.

Install SuperLive for iPhone

Install NVMS Lite 2.1 CMS, Log in & Connect Device to Monitor on Windows OS

The complete installation to monitoring steps are explained here. They are demonstrated with images and narrations for a better understanding. It is defined in three steps.

Step 1- Install NVMS Lite 2.1 on Windows

When we open the executable file, we get the following page. Here, we have to select the language.

Chooseyour language of preference and then press the ok button.

This page appears on the screen. It shows that the setup files are preparing to install.

When the setup file becomes ready, we get the next page.

It says that to install properly, take it with administrator account. Press the OK button and move to the next window.

The agreement page appears on the screen.

Select the ‘I accept the terms of the license agreement’ option and then press the next button.

The page for giving path and folder location to the software appears.

Give the proper path and folder location and then press the next button.

The files will begin to transfer on the PC.

App installation process is going on. When the process is finished, we get a new page informing it.

The installation process is finished. Press the ‘Finish’ button for the next step.

The step- 2 is about the login process.

Step 2- Log in to the NVMS Lite 2.1 App

When we open the installed app, we get the following page. It is the login page.

You have to fill the Username and password of the application. The by default username and password are respectively “admin” and “123456“.

You will login to the software. This way the step 2 is complete.

Now, we will go to add the devices.

Step 3- Add Devices for Monitoring

After the sign-in, we have to give these optional answers to recover password in case we forget them. It is an option. You can skip the process too if you want.

After that, the homepage of the NVMS Lite 2.1 appears.

We have to add the device. Press the marked option to connect devices.

This page surfaces. Press the add button now for connecting cameras.

When you press the add button, you get this page. Here, you can add cameras or devices. To add manually click the encircled button.

Fill the IP address and press ok to connect. You can add all the devices similarly.

Now move to the home page and select the live view option.

Added device will appear on screen. This way you can monitor from remote areas.

The full demonstration of this app must be helpful for readers and users.

SuperLive Plus For PC Free Download For Windows

Here you can download the latest version of Superlive Plus on your computer.

All you have to do is click on the download button according to your choice.

Superlive Plus is also available for MAC PC you can live your cameras on your MAC PC also.

Apply any given method and then you can see the live view of your cameras on your PC.

Method 1 (SuperLive Plus For PC using NVMS 1000)

Every CCTV company offers a CMS for Windows setup of its cameras. Superlive plus also offers its called NVMS 1000.

By using this, you can get a view of SuperLive plus camera on your computer screen. So download the setup for that from the given link.

Step 1.

Download the Setup from the given link below (Old Version).

Download Superlive Plus For PC

Download Superlive Plus for MAC

After downloading the setup open the folder where it has been downloaded the file name is “Superlive-Plus-for-PC. Just install this setup on your PC.

Step 2

Now come to the configuration of superlive plus for PC (windows).

After completing the installation process you will get an icon on your desktop named “NVMS-1000″. Just double click on that icon and it will ask for the registration of the user.

Here assign a user name and password and register the user. You may leave other options on the registration screen. This user name and password are only for this software not for your DVR/NVR.

Step 3

Now a new screen will open asking for the username and password. Insert the username and password that you registered at step 2. A screen will appear in front of you as shown below.

Step 4

Just click the option “Device” and you will find the next screen as shown below.

Click on the “Add Device” option and come to the next screen.

Step 5

Click on the “manually add” option from the top of the screen. Here, you have to add a device serial number, IP address or a domain as per your mode of DVR/NVR’s registration.

So choose one of them as per your desire. After filling the information. Just click on the “Test link” button. Test link must be popped up “Test connection success” then clicks “ok” and then “Add” button.

Now the device is registered successfully now you can see all the cameras on your computer screen. To do this you should go to the “live preview” option.

Method 2 (SuperLive Plus For PC using BlueStack)

To use this method you have to use an android emulator on your PC. One of the best emulators is Bluestack. Just install it on your PC and follows the steps.

• Download and install the emulator.

• You will get an icon of the emulator to appear on the desktop.

• Now find the play store icon on the emulator. It is just like your android phone.

• Login to your play store.

• Search for the Superlive plus and install it.

• Now just put the information in the process of registration device.

• Just enjoy Superlive Plus for PC.

SuperLive Plus For PC Free Download For MAC

If you have a MAC system then you can also get your cameras on your MAC system. The company also offers set up it on your MAC OS. Here we are going to demonstrate how to download and configure super live plus for PC(MAC).

Step 1

Download the setup of superlive plus for pc from the given link below.

Download Superlive Plus for PC (MAC)

Just install it on your PC and come to the second step.

Step 2

Now you can see an icon on your computer screen named “MAC Super CMS…app”. Just open it and the screen will ask you for the account creation. Just create an account for that by putting a username and password.

After the registration window will ask you to log in. just logged in by using the username and password that you registered.

Step 3

After logging in you can see the screen as shown below.

On your right bottom, an option shows as “Add”. Click on that icon and you will see the next screen.

Step 4

In this step, a screen will appear as shown below.

It asks for some detail related to your device. Just fill it up. In the “Title” option you can choose a title your device as per your choice. In the address, you have put the IP address of the device(DVR/NVR/IP camera).

Title: As per your choice.
Address: The IP address or domain name of the device you want to add.
Port: The HTTP port of the device you want to add.
Account: The login account of the device. The default account is “admin”.
Password: The login password of the device. The default password is 123456.

Step 5

Now click on the “Save” button to save the information. Now you can see the DVR/NVR list in the device list as shown in the below picture.

Conclusion

So this is all about Superlive plus for PC. Using these steps you can easily configure the SuperlivePro DVR/NVR/IP camera for your window laptop and desktop. If you have any queries or suggestion please write to us in the comment box below.

Frequently Asked Question

What is NVMS Lite Edition?

NVMS Lite Edition and NVMS Lite 2.1 Edition are security management platforms given by TVT. They are software for connecting CCTV devices for remote access. You can be live from any place and monitor your locations.

What is the password for Nvms Lite Edition?

The by-default username and password for the NVMS lite are “admin” and “123456” respectively.

What is NVMS software?

It is a security surveillance app. It is designed to monitor CCTV devices from remote areas. It is available for Android, iPhone, Windows and Mac versions. It supports TVT cameras and recorders. It also connects some third-party devices.

What is the default IP address of the TVT CCTV camera?

The company has provided the following IP address and by default setting. IP address: 192.168. 226.201 Subnet Mask: 255.255. 255.0 Gateway: 192.168. 226.1 HTTP: 80 Data port: 9008 The default password of the administrator is “123456”

What is the default password for TVT security cameras?

The default password for CCTV cameras is 123456.

Hikvision How-To Tutorials Part1

admin — Thu, 04 Jan 2024 06:11:58 +0000

Hikvision How-To Tutorials Part1, Hikvision provides top-of-the-line AIoT solutions and reliable security camera systems to empower advanced monitoring and automation and improve security.

How do I use a Hikvision NVR’s “Virtual Host” feature?

Hikvision How-To Tutorials Part1

How Do I Configure the Camera’s Onscreen Display Text?

All Hikvision users will have seen that when you first log in to a camera the live view will have overlayed text stating the date & time and the default name of the camera “IPcamera 01″, depending on your requirements you may want to change some or all of this overlay text and below is the instruction for how to do that.

Method 1 – In a Web Browser

Below we will take you through each of the above settings and what they do:

Character Set – This lets you select the characters/language the OSD settings use, by default all UK stock will come with this set as GBK for English characters but if you are a European customer and you want to enter special characters from your particular language (e.g. é, ü, ç, etc…) you can switch it to EUC-KR to access those characters (do this will require the camera to reboot).

Display Name / Date / Week – These tick boxes let you show/hide the camera name (Display Name), the current date (Display Date), and the day of the week (Display Week)

Camera Name – This box lets you set the displayed name of the camera, it will also change the name of the camera shown in the System menu and if added to an NVR it will change the name shown in the live view camera list and the Camera Management list.

Time Format – This dropdown lets you select how the time appears in your live view, either 24-hour format (00:00 – 23:00) or 12-hour format (00:00 – 12:00)

Date Format – This dropdown lets you select how the day, month, and year are displayed. Your options are DD/MM/YYYY (UK format), MM/DD/YYYY (US format), and YYYY/MM/DD (Chinese/International Standard format). You also have the option of separating the day, month, and year with either a “–” or a “/“.

Text OverLay – On most cameras, you should have the option to add up to 4 additional text overlays to the live view. You can use all of them or none of them depending on your requirements.

Display Mode – This dropdown lets you choose how the text behaves on screen, by default it will usually be set to Not Transparent & Not Flashing which means the text will obscure objects/people behind it and it will be onscreen all the time. You have the option to change it to one of the following – Transparent & Flashing / Transparent & Not Flashing / Not Transparent & Flashing – When set to transparent the text will become semi-transparent so that you can see objects/people behind the text and if set to flashing the text will flash on & off screen every few seconds (there are no controls for the flashing duration).

OSD Size – Technically this setting should adjust the size of the OSD text but we’ve found that when changing it there was little change to the text and so we would just stick to the default Auto option because this will allow the text size to adapt based on where you are viewing the live image (e.g. whether a small phone screen or a large TV).

Font Color – This dropdown lets you select the colour used by the OSD text, by default the camera will use Black&White Self-adaptive which means the text colour will automatically switch between black & white based on what is behind the text (e.g. if a person walks through the text) and for high-security sites, this can be an important feature for using the footage in court because the adaptive text shows that the image/text has not been manipulated in post. If the scenario requires it you can select Custom which will allow you to pick the text colour from a standard colour table.

Alignment – Again like OSD size this setting doesn’t appear to have a huge impact so we would just leave it as the default Custom and you can adjust the positioning/alignment of the OSD text by dragging the red boxes around the live view window above (these red boxes are only for adjusting the text position and will not appear on the actual live view image).

Method 2 – Via the NVRs GUI

You can access similar OSD settings from the NVR by going to Camera > Display and selecting the camera you want to configure.
.

Although, as you can see from the above screenshot you won’t get all the settings that can be found by logging into the cameras directly.

How do I stop my Hikvision NVR from beeping?

If a Hikvision NVR notices what it deems to be a critical error, or “exception”, it will make a constant beeping sound to draw your attention to this.

These exceptions can occur when:
.

• A hard drive has not been installed or properly formatted

• There is an error with the hard drive, it has been damaged, or the cameras are just not recording properly

• A hard drive has been filled and not set to overwrite

• There is an IP conflict, preventing the NVR from operating properly

• The NVR detects an illegal login

• The NVR loses its network connection

Of course, ignoring these exceptions are not recommended. However, you can disable the beeping while you address whatever the issue is by following the steps below.
.

Step 1:

Connect to your NVR in a web browser by using its IP address and logging in.

Step 2:

Check what the exception that is causing the beeping is in the NVR’s logs. To find these, go to:

Configuration → System → Maintenance → Log

Set the log search so that the “Major Type” is “Exception”, with the start and end time covering a period when the beeping has occurred.

For example, you can see that it is an IP address conflict causing it in this case.

Note – Camera disconnections will not cause the NVR to beep.

Step 3:

Go to:

Configuration → Event → Basic Event → Exception

Find the “exception type” identified in step 2 in the dropdown on this page.

Step 4:

Select the exception shown in your logs from the dropdown.

You will see that “Buzzer” is ticked as a “Normal Linkage” action, which is what is causing the NVR to beep.

Step 5:

Untick this, click “Save”, and the beeping should stop.

How to Set Up UniFi

admin — Tue, 28 Nov 2023 11:28:59 +0000

How to Set Up UniFi, UniFi is a powerful and intuitive operating system enabling an end-to-end management experience for all of your IT needs. When paired with our specially designed hardware, you will have unparalleled control over your network and WiFi, security cameras, VoIP phones, door access, smart enterprise lighting, digital signage, and much more!

UniFi OS is pre-installed on UniFi Consoles, streamlining the setup process so you can get your network up and running quickly. Although it is possible to self-host the UniFi Network Server or setup Access Points (APs) in Standalone Mode, these methods lack key advantages including automated backups, system updates, and more advanced software offerings.

If you are new to UniFi, we encourage you to check out Introduction to UniFi to learn more about device adoption, remote management, and the UniFi ecosystem in general.

Have You Purchased a UniFi Console?

Our UniFi Consoles are built to run UniFi OS and come pre-installed with all UniFi Applications. This includes things like the Dream Machine, Dream Router and Cloud Key G2 Plus. With these consoles, it’s easy to automatically establish backups, update hardware and software, and ensure maximum compatibility by minimizing third-party inter-operation.

Set Up a Console

UniFi Consoles can be setup from the web or our mobile app. Regardless of which method you choose, you will be able to continue managing UniFi both via the mobile app and web following the initial setup.

Using the Mobile App (Recommended)

Using a Web Browser

Do You Have an Access Point Without a Console?

Standalone Mode should only be used when configuring a small quantity of APs because they do not support seamless roaming. Instead, you will need to manually connect to each AP as you move out of range. Also, APs must have a wired connection to your network; wireless meshing is not possible. Finally, remote management is not possible because it is done entirely through the UniFi Mobile app while locally connected to your WiFi.

For information on Standalone Access Points, check out our article here.

How to Set Up UniFi

Do You Plan to Host a Server Yourself?

UniFi can also be self-hosted on a Windows/macOS/Linux machine, but this is only recommended for users proficient with network administration, because it requires constant and precise attention. You’ll need to manually configure your network for sufficient communication between UniFi Network and all of your networking devices. Success hinges on your ability to continuously navigate various third-party software, firewalls and other networking devices.

For information on Self-Hosting, check out our article here.

Common Troubleshooting

Our setup flow is designed to be as seamless as possible. However, some circumstances, often related to external network configurations, may cause setup failures.

Check Your Physical Connections

Ensure that your power and network connections are secure. If they are, but your issue persists, we recommend using our UniFi cables for optimal compatibility and performance.

Verify Your UniFi Console’s Internet Connection

UniFi Cloud Gateways (UniFi Consoles such as our Dream products, which contain an integrated security gateway) are usually connected directly to the internet. However, non-gateway consoles, such as the Cloud Key Gen2 Plus, can be incorrectly placed on a network or VLAN with restricted internet access. Please ensure this isn’t the case for your consoles.

Update to the Latest Version of UniFi OS

For the best setup experience, we recommend updating to the latest version and ensuring that automatic updates are enabled.

Open All Required Ports

Third-party gateways, firewalls, and Internet Service Provider (ISP) modems occasionally block traffic required for set up. Some of these include:

• TCP & UDP Port 443

• TCP Port 8883

• TCP & UDP Port 53

• UDP Port 123

• TCP Port 3478

See Required Port Reference for a complete listing of all requisite ports. You may wish to contact your ISP to ensure none of these are being blocked. We also recommend disabling any third-party firewalls.

Clone Your ISP Router or Modem’s MAC Address

Some ISPs restrict connectivity to certain MAC addresses. You may need to clone your modem or router’s MAC address in order to set up your UniFi Console. We recommend contacting your ISP first to confirm whether or not this is necessary.

Contact Your ISP

If you’ve tried all of the tips above but are still having setup issues, please contact your ISP to ensure that they have not restricted your UniFi Console’s connectivity.

Standalone Access Points (without UniFi)

UniFi access points (APs) can be set up and configured without any additional devices, but their features will be limited.

We recommend using a UniFi Cloud Gateway (e.g., Dream Machines and Dream Routers) or a dedicated UniFi Console (e.g., Cloud Key G2 Plus) to access our full features, including an integrated internet gateway for advanced network security, detailed traffic analytics, seamless VPN access, and powerfully intuitive Policy-Based Routing (PBR).

Limitations

Be aware of the following limitations of Standalone Mode:

• Each AP must be individually configured.

• Seamless and quick roaming (802.11r/k/v) between multiple access points is not supported.

• AP management is limited to the UniFi Mobile App (web not supported) using independent credentials that are not associated with your UI Account.

• No remote management; APs can only be viewed and configured by users connected to the local WiFi.

Setting Up Your APs

1.Plug your UniFi AP into your network.

a.Note: Ethernet jacks in the wall may not actually be connected to your router/gateway/modem.

2.Power your AP with a compatible PoE Switch or PoE Adapter.

a.See UniFi PoE Availability and Modes to learn more.

3.Log in to the UniFi Mobile App (iOS / Android).

4.Scan the QR Code on the back of your AP.

5.Follow the instructions on screen to finish the setup process and create a new WiFi instance.

Unable to Join the Network ‘UniFi’

Our APs broadcast a hidden WiFi used just for device setup. If you cannot connect to it, a mistake was made during your setup process.

My AP is not powered on, or in a factory state.

Your AP should emit a solid white LED indicating that it is turned on and ready to be set up. If the LED is off, make sure it is receiving proper power. Consult your AP’s specifications to confirm its required power input.

A solid blue LED indicates that the device was already set up. In this case, you should factory reset it and try again.

My AP does not have network connectivity.

APs must receive an IP address from your network- from your ISP modem, or a third-party router/gateway.

Verify if your AP has an IP address by using the Discovery feature in our WiFiman Mobile App (iOS / Android). If the device does not appear, or it appears with our ‘fallback IP address’ (192.168.1.20), this indicates a problem with your network’s configuration. Make sure your AP is properly connected to a local network port (LAN) of your modem or gateway/router.

UniFi – How to Reset Devices to Factory Defaults

A factory reset is useful for a creating fresh setup of a UniFi Console, or device that was already configured in a managed state.

Restoring with the Reset Button

All UniFi devices have a Reset button. You can return a device to a factory-default state by holding this for 5-10 seconds (depending on the device), or until the LEDs indicate the restore has begun. Your device must remain powered during this process.

Example: The diagram below illustrates how to locate this button on the UDM Pro.

Restoring From Your UniFi Application

UniFi Devices

All UniFi devices can be restored to their factory defaults via their respective web or mobile applications. This is located in the Manage section of a device’s settings. Depending on the application, this may be referred to as Forget (UniFi Network) or Unmanage (UniFi Protect).

Selecting this option will unmanage the device from your UniFi Console and restore the device to a factory default state.

UniFi Consoles

A UniFi Console admin with Owner privileges has the ability to restore their console using the “Factory Reset” button located in the UniFi OS System settings.

Frequently Asked Questions

Why does my device still appear in my application after I restored it using the physical Reset button?

The physical reset button does not remove the device from any applications it was adopted to. This can be done under the Manage section of the device settings.

Why does my device say “Managed by Other”?

This will occur if the device was managed by another instance of a UniFi application. This includes cases where the UniFi Console (e.g., Dream Machine Pro, or Cloud Key) was factory restored, because the UniFi device still considers itself as being managed by the ‘old’ application console, prior to restoration.

There are several options to resolve this:

• Restore the UniFi Console from a backup in which the device was already managed.

• Factory restore the UniFi device and then re-adopt it.

• Reassign the device using the UniFi Network mobile app.
Note: This can only be done by the account owner and requires them to have previously signed into the mobile app while the device was managed.

Note: If you are self-hosting the Network application, you should only ever download the UniFi software on a single machine which will act as the UniFi Network Server. Some users mistakenly download this multiple times because they believe it is a requirement to manage their Network Application from other devices, but this is actually creating a completely new instance. To manage your network from another device, you can type in the IP address of the UniFi Network Server while connected to the same local network. Alternatively, you can enable Remote Access to manage your network anywhere. See Connecting to UniFi to learn more.

Why is my UniFi Device not factory restoring?

Ensure that your device remains powered on during the restoration process, otherwise it will not occur.

It is also possible that you held the button for too short of a time (resulting in a reboot), or too long of a time (resulting in entering TFTP Recovery Mode). Refer to our UniFi Device LED Status guide for more information.

UniFi Network – Understanding Device LED Status Indicators

Learn how to identify your device’s state based on the LED color patterns. These blue and white status LEDs apply to all our UniFi access points, routers, switches, and the UDM base model.

Status LED Patterns

Note: The animations are for illustrative purposes – the speed of the flashing or strobing patterns below might differ slightly from your device’s.

Flashing White / Off Every 1/2s

The device is initializing and booting up.

Steady White

The device is ready for adoption.

Slow Flashing Blue (UDM Only)

A client device is connected to the UDM via Bluetooth.

Blue and Flashing Off Every 5s (UDM Only)

There is no internet connection to the UDM.

Steady Blue

The device is adopted and is in normal operating mode. Access Point is broadcasting WiFi.

Strobing White / Off

If this happens, power cycle the Access Point.

If this doesn’t help, please reach out to our support team.

Quickly Flashing White / Blue

The device firmware is currently being upgraded – do not interrupt the process.

UDM will flash only white during an upgrade.

Blue and Flashing Off Every 5s

Access Point has lost network connectivity and is searching for a wireless uplink.

Rapid Flashing Blue / Off

The device “Locate” feature was activated in the UniFi Network application.

Flashing White-Blue-Off

The device is in TFTP mode.

To enable this mode:

1.Hold the reset button before powering on.

2.Continue to hold the reset button until this LED sequence appears.

If this wasn’t intentional, please ensure the device’s reset button isn’t jammed (it should click when pushed).

LED Off

The device is offline.

Verify the Power, POE, and Ethernet cables to troubleshoot.

UniFi Bridge to Bridge (UBB)

Including the statuses described above, the UBB has two additional ones:

Red with Circulating Blue LED

The 60 GHz link cannot be established or has dropped due to bad weather. If the UBB fails over to 5 GHz, the LED will remain red. When the 60 GHz link is re-established, the LED will turn blue (or the custom color selected in the UniFi Network application).

Note: If the other bridge device is within range and the UBB LED is red, we recommend adjusting the UBB’s position to enhance the signal strength.

Green

If the Alignment Tool enabled in the UniFi Network application, a green LED means the UBB devices are properly aligned.

Note: If the other bridge device is within range and the UBB LED is green and red, we recommend adjusting the UBB’s position until the LED is green.

LED Patterns for Ports

The ports of UniFi Security Gateways and UniFi Switches have a different type, number, and location.

Please refer to your specific device model’s Quick Start Guide (QSG) for the exact location and description of its ports.

Console Port’s right LED (in the applicable devices):

• LED Off: Power Off

• LED Green: Power On

Speed/Link/Act (right LED ports other than Console):

• LED Off: No Link

• LED Amber: Link Established at 10/100 Mbps

• LED Flashing Amber: Link Activity at 10/100 Mbps

• LED Green: Link Established at 1000 Mbps

• LED Flashing Green: Link Activity at 1000 Mbps

PoE (left LED on ports of applicable devices):

• LED Off: No PoE

• LED Amber: IEEE 802.3af/802.3at

• LED Green: 24V Passive

SFP (in the applicable devices):

• LED Off: No Link

• LED Green: Link Established at 1 Gbps

• LED Flashing Green: Link activity at 1 Gbps

See specific port LED information in the Hardware Overview section (between pages 5 and 6) of the Quick Start Guides (QSG). You can find the QSGs in the Documentation section of our UniFi Downloads page, by searching for the device in question in the left-hand menu.

LED Patterns for PoE Adapters

LED is Off: PoE is Off.

LED is On and steady: PoE is functioning as it should.

LED is blinking: this is not a configured state, this may indicate that the device is not connected properly, or that something is wrong with the cable.

How to Disable Device LEDs

The device status LEDs can be disabled for all the site, or only for specific UniFi devices.

To enable/disable status LEDs throughout a site, go to to Settings > Site on the UniFi Network application and edit the LED feature in the Services section.

To configure specific devices individually:

1.Go to the Devices section and click on the device you wish to edit to bring up the Properties panel

2.Go to Config > General > LED and switch the Site Settings to On or Off.

Introduction to UniFi

UniFi is a powerful and intuitive operating system enabling an end-to-end management experience for all of your IT needs. When paired with our specially designed hardware, you will have unparalleled control over your network and WiFi, security cameras, VoIP phones, door access, smart enterprise lighting, digital signage, and much more!

Check out ui.com to learn how we can help simplify your IT management!

UniFi Consoles

The UniFi experience begins with one of our UniFi Consoles. These were created to run our UniFi software which allows you to manage your network and WiFi, security cameras, VoIP phones, door access and more!

UniFi Cloud Gateways combine the power of a UniFi Console with an integrated internet gateway. This brings you advanced network security, seamless VPN access, detailed traffic analytics and more.

A Cloud Gateway is all you need to hit the ground running with your home or office network.

For further customization, we offer specialty UniFi Consoles to fit specific needs:

• UniFi Network Video Recorder (UNVR), a dedicated, high-capacity Console running UniFi Protect only. This can be used alone, or it can pair with an existing UniFi Console to add additional scalability for your security cameras. Stack multiple UNVRs together for bigger deployments, and take advantage of RAID storage technology, providing data redundancy and protection against disk failure.

• Cloud Key G2 Plus, a versatile UniFi Console ideal for smaller stand-alone camera security, VoIP, or door access applications. It also serves as a low-cost, plug-and-play replacement for a self-hosted UniFi Network server because it delivers the benefits of UniFi OS, such as automatic cloud backups and system updates.

• Official UniFi Hosting, UniFi’s native hosting subscription service that offers scalable management of large quantities of devices without requiring you to install a hardware console on-site. It pairs well with our Gateway Professional to deliver a full-featured UniFi Network.

Note: While some users choose to self-host their UniFi Network application, we do not recommend self-hosting unless you are highly familiar with networking administration. Invalid configurations may lead to system crashes, poor performance, and compromised network security.

For more details, please see our recommendations in Which Ubiquiti UniFi Console is Right For Me?

UniFi Applications

The UniFi application suite is thoughtfully constructed to serve a wide variety of technological needs within your home or business:

• UniFi Network – An incredible platform packing together powerful internet gateways with scalable WiFi & switching into an integrated management platform. Get insights into your network like never before with real-time traffic dashboards, visual topology maps, and even smart tips suggesting opportunities you can optimize.

• UniFi Protect – A constantly evolving, AI-driven camera platform capable of recording high-quality video for local storage. Sorting through footage has never been easier thanks to our smart detection capabilities. It brings versatile control over recording schedules, camera access, and even how notifications are sent to administrators.

• UniFi Talk – A new approach to business telephony. UniFi Talk is a plug-and-play phone system and VoIP subscription service designed for small and medium-sized businesses. Powerful call routing and admin features ensure you never miss another call. Our thoughtfully designed, touchscreen phones offer breakthrough user experiences and bring smartphone-level usability to desk phones.

• UniFi Access – A state-of-the-art access control system with modern touch-screen access readers, live video, and mobile app credential support. Easily manage users, visitors, schedules, and access policies like never before.

• UniFi Connect – A modern Enterprise of Things platform that consists of digital signage, lighting, and electric vehicle charging stations. Leverage UniFi Connect’s simply scalable management capabilities to manage everything from a single Connect Display running an interactive point-of-sale application to an entire building’s worth of lighting and dynamic content.

Adopting Devices

Device adoption is the process of setting up a device and linking it to the respective UniFi application so you can manage it. For more details, see Device Adoption.

Remote Access and Your UI Account

Your UI Account allows you to manage UniFi from anywhere in the world using our UniFi Site Manager at unifi.ui.com, or our UniFi Mobile Apps (iOS / Android). See Connecting to UniFi to learn more about remote and local connections.

Other benefits of using a UI Account include:

• Secure multi-factor authentication, including our seamless single-touch solution with UI Verify (iOS / Android).

• Automatically schedule backups and updates.

• Configure email and mobile push notifications for important system activity.

Standalone Access Points (without UniFi)

UniFi access points (APs) can be set up and configured without any additional devices, but their features will be limited.

Limitations

Be aware of the following limitations of Standalone Mode:

• Each AP must be individually configured.

• Seamless and quick roaming (802.11r/k/v) between multiple access points is not supported.

• AP management is limited to the UniFi Mobile App (web not supported) using independent credentials that are not associated with your UI Account.

• No remote management; APs can only be viewed and configured by users connected to the local WiFi.

Setting Up Your APs

1.Plug your UniFi AP into your network.

a.Note: Ethernet jacks in the wall may not actually be connected to your router/gateway/modem.

2.Power your AP with a compatible PoE Switch or PoE Adapter.

a.See UniFi PoE Availability and Modes to learn more.

3.Log in to the UniFi Mobile App (iOS / Android).

4.Scan the QR Code on the back of your AP.

5.Follow the instructions on screen to finish the setup process and create a new WiFi instance.

Unable to Join the Network ‘UniFi’

Our APs broadcast a hidden WiFi used just for device setup. If you cannot connect to it, a mistake was made during your setup process.

My AP is not powered on, or in a factory state.

A solid blue LED indicates that the device was already set up. In this case, you should factory reset it and try again.

My AP does not have network connectivity.

APs must receive an IP address from your network- from your ISP modem, or a third-party router/gateway.

Introduction to UniFi

Check out ui.com to learn how we can help simplify your IT management!

UniFi Consoles

UniFi Cloud Gateways combine the power of a UniFi Console with an integrated internet gateway. This brings you advanced network security, seamless VPN access, detailed traffic analytics and more.

A Cloud Gateway is all you need to hit the ground running with your home or office network.

For further customization, we offer specialty UniFi Consoles to fit specific needs:

For more details, please see our recommendations in Which Ubiquiti UniFi Console is Right For Me?

UniFi Applications

The UniFi application suite is thoughtfully constructed to serve a wide variety of technological needs within your home or business:

Adopting Devices

Device adoption is the process of setting up a device and linking it to the respective UniFi application so you can manage it. For more details, see Device Adoption.

Remote Access and Your UI Account

Other benefits of using a UI Account include:

• Secure multi-factor authentication, including our seamless single-touch solution with UI Verify (iOS / Android).

• Automatically schedule backups and updates.

• Configure email and mobile push notifications for important system activity.

Connecting to UniFi and Remote Management

UniFi allows you to access and manage your UniFi ecosystem from a web browser or our UniFi Mobile Apps, with ease and security.

Using a Web Browser

It’s easy to connect to your UniFi Console through your preferred browser. We generally recommend using the UniFi Site Manager for a simple, secure, and convenient way to manage all UniFi deployments associated with your UI Account.

How to Connect Remotely (UniFi Site Manager)

1.Enable Remote Management from your UniFi OS settings. This is enabled by default when you set up a UniFi Console using your UI Account.

• Legacy Cloud Keys and self-hosted Network Servers can find this in Settings > System > Administration.

2.Go to the UniFi Site Manager and sign in with your UI Account credentials.

How to Connect Locally (Local Site Manager)

The Local Site Manager is great when the remote UniFi Site Manager is unavailable, for example during an Internet outage. You may also note improved UniFi dashboard load times and lower latency when locally viewing high-bandwidth recordings from UniFi Protect.

1.Enter the IP Address of your UniFi Console into your browser’s address bar.

• If you don’t know your UniFi Console’s IP address, use the WiFiman app (iOS / Android) to locate it on your network.

• Users with a UniFi Console or Gateway (i.e., Dream Router, Dream Machine, Dream Wall, Next-Gen Gateway Pro, etc.) can simply enter unifi/ into the address bar.

2.If you receive a privacy or security warning, this is normal. Select the option that allows you to proceed.

3.Log in using your UI Account or local credentials.

• If you set up your UniFi Console (Dream products, Cloud Key Gen2 Plus, etc.) offline without a UI Account, the default username is ‘admin’.

Using a Mobile Device

Download our UniFi Mobile App (iOS / Android) and sign in using your UI Account to automatically see all UniFi Consoles compatible with UniFi OS associated with that account. If you have not enabled Remote Management, you can do so within your UniFi OS settings*.

*UniFi Consoles that are not compatible with UniFi OS, such as legacy Cloud Keys and self-hosted Network Servers can find this in Settings > System > Administration.

Local-only Access

Some users may optionally add a local-only connection. This is done by manually specifying your UniFi Console’s IP Address, Port (8443 for self-hosted Network Servers, and 443 for consoles running UniFi OS), Username*, and Password. Please note that restrictive network configurations or firewall rules may inhibit your ability to connect using this method.

*UniFi Console (Dream products, Cloud Key Gen2 Plus, etc.) offline without a UI Account, the default username is ‘admin’.

Direct Connections

Direct Connections establish a higher-performing management session when connecting with your UniFi Console. This is useful for any remote admin who regularly checks video footage, or manages a very large network with multiple access points. You can learn more here.

For your convenience, the UniFi Site Manager automatically establishes a Direct Connection when you are on the same local network as your UniFi Console.

Direct Remote Connections

It is also possible to establish a Direct Connection when remotely connected through the UniFi Site Manager from outside of your network. The Direct Remote Connection setting can be enabled in either your UniFi OS settings, or your UniFi Network Advanced Settings.

Note: This setting requires a UniFi Gateway with a public IP. Additionally, TCP Port 443 must be open and not used in a port forward rule.

Remote Access Privacy and Security

Remote access is a secure method of connecting to your UniFi Console from anywhere using your UI Account credentials. We prioritize facilitating direct connections with your local UniFi Console as a means of bolstering data security and optimizing low-latency connectivity. A new admin must be invited by the UniFi Owner in order to gain access. Once granted access, our UI Accounts support multi-factor authentication to ensure maximum security.

Ring APP How to Use Part1

admin — Sat, 25 Nov 2023 14:32:32 +0000

Ring APP How to Use Part1, Watch over your property from anywhere with Ring Video Doorbells and Security Cameras.Ring Video Doorbells and Security Cameras can send you real-time alerts when someone’s at your door or motion is detected. Keep an eye on what matters with live HD video and greet visitors with Two-Way Talk. With a compatible Ring Protect subscription (or free trial), you can review, save and share your Ring videos.

Whether you’re halfway around the world or just popping out to the shop, with Ring, you’re always home.

What you can do with the Ring app:
– Get real-time doorbell and motion alerts on your smartphone or tablet
– See and speak with visitors with HD Video and Two-Way Talk
– Arm and disarm your Ring system
– Allow access to your building for authorised guests and services with Ring Intercom

Using Live View

Use Live View to stream real-time video from your Ring Video Doorbells and Security Cameras on the Ring app or on Ring.com without a Ring Protect subscription. Both Account Owners and Shared Users can access Live View.

If you have a Ring Protect subscription, you can get video recordings of Live View actions and events within 1-2 minutes.

Ring APP How to Use Part1

Actions in Live View

Depending on which Ring device you’re using, there are certain actions you can take while using Live View.

• Enable Sound – Listen in on what’s going on in your property. Select the speaker button to enable.

• Two-Way Talk – Speak to whoever’s there.

◦ Select the microphone button to start talking.

• Activate Siren – Sound a security camera siren.

◦ Select the exclamation button and confirm on the pop-up dialog.

• Turn on Lights – Turn on your lights.

◦ Select the light button to turn on or off.

Live View will automatically turn off after 10 minutes.

How to use Live View in the Ring app

1.Open the Ring app.

2.Tap a Snapshot image from your doorbell or security camera. Live View will open.

3.Depending on which device you’re using, there are certain things you can do:

◦ Enable sound by tapping the speaker button (available for doorbells and security cameras).

◦ Use Two-Way Talk by tapping the microphone icon (available for doorbells and security cameras).

◦ Turn on lights by tapping the light button (available for security cameras with lights)

◦ Activate siren by tapping the exclamation button (available for security cameras).

4.To end Live View, tap the End Live button.

Note: Some features may require you to update your mobile device’s operating software and download the latest version of the Ring app to access.

How to access Live View

If you have several doorbells or security cameras at the same Location, you can access Live View for each device separately.

1.Tap the menu (≡) on the top left in the Ring app.

2.Tap Devices, and select a doorbell or security camera.

3.Tap Live View.

4.Depending on which device you’re using, there are certain things you can do:

◦ Enable sound by tapping the speaker button (available for doorbells and security cameras).

◦ Use Two-Way Talk by tapping the microphone icon (available for doorbells and security cameras).

◦ Turn on lights by tapping the light button (available for security cameras with lights)

◦ Activate the siren by tapping the exclamation button (available for security cameras).

5.To end Live View, tap the End Live button.

Using Live View on Ring.com

Account owners and Shared Users can also use Live View from Ring.com, after logging in with the same username and password used to access the Ring app.

Supported browsers

Live View is only supported in certain browsers. See the table below for the latest compatibility information.

Browser	Desktop version	Mobile version (Android)	Mobile version (iOS)
Google Chrome	84.0 or later	84.0 or later	84.0 or later
Safari	13.0 or later	N/A	15.0 or later
Firefox	95.0 or later	95.0 or later	40.2 or later
Microsoft Edge	84.0 or later	84.0 or later	84.0 or later
Opera	70.0 or later	61.0 or later	3.2 or later
Brave	1.12 or later	1.12 or later	1.12 or later
Samsung Internet	N/A	13.0 or later	N/A
Silk	N/A	84.0 or later (FireOS)	N/A

Accessing Live View on Ring.com

1.Log into your Ring account using the same email and password that you use for the Ring app.

2.Select one of the Snapshot images under the Cameras section for a camera or doorbell. Live View will open.

3.Depending on which device you’re using, there are certain things you can do:

◦ Enable sound by selecting the speaker button (available for doorbells and cameras).

◦ Use Two-Way Talk by selecting the microphone icon (available for doorbells and cameras). Your browser may ask you to give Ring.com permission to access your microphone. If this happens, select Allow.

◦ Turn on lights by selecting the light button (available for Spotlight Cams and Floodlight Cams).

◦ Activate the camera siren by selecting the exclamation button.

4.To end Live View, select the End Live button.

Turning off Live View

1.Open the Ring app and tap the menu (≡) at the top left.

2.Select Devices and choose a camera or doorbell.

3.Select Video Settings.

4.Toggle Camera Preview for Live View.

Live View is turned off for that device now. Repeat this process for other devices, as needed.

Finding Your Internet Upload Speed

Learn how to see your Internet Upload Speed in the Ring app or your account at Ring.com.

Code: W4-04

Internet Upload Speed is how fast your Ring device sends data like encrypted Ring videos to the internet.

This feature will be available for all customers soon.
We are slowly rolling out this feature. If you don’t yet see your Internet Upload Speed in the Ring app or your Ring account, it will be available soon.

This speed test is measured in megabits per second (Mbps) and runs periodically to make sure your Ring device maintains a good internet upload speed.

Viewing your Internet Upload Speed from your account at Ring.com

1.Log in to your account at Ring.com.

2.Click the settings (gear) icon for the device for which you want to view Transmit Speed.

3.In the Device Health section, you can see your Internet Upload Speed.

Internet Upload Speed results guide

• GOOD: More than 10 Mbps

• OKAY: 5–10 Mbps

• POOR: Less than 5 Mbps

• NO DATA: No results yet

Keep in mind, your Internet Upload Speed is also affected by upload activity from other devices on your local network, such as additional Ring cameras, phones, laptops, tablets, and gaming consoles.

If your Internet Upload Speed is poor, we recommend contacting your Internet Service Provider to upgrade your internet plan or troubleshoot your low upload speed.

Finding Your Ring Device’s Transmit Speed

Learn how to see your Ring device’s Transmit Speed in the Ring app or your account at Ring.com.

Code: W4-05

Your Ring device’s transmit speed over wifi (or ethernet) is the speed of the direct connection between your Ring device and your local network (i.e. your router) when uploading data like Ring videos.

This feature will be available for all customers soon.
We are slowly rolling out this feature. If you don’t yet see your Ring device’s Transmit Speed in the Ring app or your Ring account, it will be available soon.

This speed test is measured in megabits per second (Mbps) and runs periodically to make sure your Ring device maintains a good connection to your local network.

Viewing your Ring device’s Transmit Speed from your account at Ring.com

1.Log in to your account at Ring.com.

2.Click the settings (gear) icon for the device for which you want to view Transmit Speed.

3.In the Device Health section, you can see your Ring device’s Transmit Speed.

Transmit Speed results guide

• GOOD: More than 20 Mbps

• OKAY: 10–20 Mbps

• POOR: Less than 10 Mbps

• NO DATA: No results yet

Is your wifi connection less than 10 Mbps? Try moving your wifi router closer to your Ring device to minimize the amount of physical objects, like walls or furniture, that may be blocking your wifi signal.

If you are receiving a device offline message in the Ring app, follow the instructions on the error message to improve your Ring device’s connection.

Managing Your Authorized Logged-In Devices

Learn how to manage which devices are logged in and authorized to access your Ring account.

Get to know Authorized Client Devices

In Control Center, you can manage the phones, tablets, and computers that are authorized to log in to your Ring account. Each time you successfully log in to Ring with your password and verification code, that device is saved as an Authorized Client Device with the following details:

• Device type

• Device operating system

• Date device was first authorized

How to access Authorized Client Devices in Control Center.

From the Ring app:

1.Open the Ring app.

2.Tap the top menu (☰).

3.Tap Control Center.

4.Tap Authorized Client Devices.

From a mobile browser:

1.Log in to your Ring account at Ring.com.

2.Tap the top menu (☰).

3.Tap Control Center.

4.Tap Authorized Client Devices.

From a desktop browser:

1.Log in to your Ring account at Ring.com.

2.Click the Dashboard home icon on the top right.

3.Click Account and select Control Center.

4.Click Authorized Client Devices.

Removing Authorized Client Devices

You have the option to delete one authorized device at a time, or all devices at once (except for the device you are currently using).

Deleting One Device
When you delete a single device, you are immediately removing this device’s ability to access your Ring account. For example, if you gave your old phone or tablet to a friend, you should delete this device from your list of devices authorized to access your Ring account.

Removing All Devices
If you Remove All Devices, you are revoking access for all devices that are authorized to access your Ring account – except for the device you are currently using.

Shared Users, not passwords.

Do not share your password with anyone.
No Ring employee, Customer Support Associate, or Community Manager will ever ask you for your password.

If you want to share access to a Ring device with a friend or family member, you can add them as a Shared User.

What to do if your Ring account has been compromised

1. Change your password immediately.
When you use the same password for multiple online accounts, you are at risk to cybercriminals (or bad actors). For example: If a bad actor acquires your password through a data breach of your email provider and you use the same password for your Ring account, this makes your Ring account more vulnerable.

Because we require an additional layer of account security with Two-Step Verification, your Ring account is still protected. However, we strongly recommend you change your password immediately.
Learn how to change your Ring password

2. Remove Authorized Client Devices you don’t recognize.
If you suspect your Ring account has been compromised, remove any and all devices that you confidently didn’t authorize.

3. Contact our Customer Support Team.
After you’ve successfully changed your password, please Contact Us so we can take proper measures to help prevent further risk.

Your account security is our highest priority

Customer trust is important to us and we take the security of our devices and services extremely seriously. We encourage all Ring users to follow our recommended security best practices to ensure your Ring account stays secure.

Account Management in Control Center

Learn how to update your Ring account information like your name, email, phone number, password and more.

Get to know Account Management

With Account Management, you can manage your Ring account information: how your name appears in your account, change your phone number, update your email, and change your Ring account password.

How to access Account Management in Control Center.

From the Ring app:

1.Open the Ring app.

2.Tap the top menu (☰).

3.Tap Control Center.

4.Tap Account Management.

From a mobile browser:

1.Log in to your Ring account at Ring.com.

2.Tap the top menu (☰).

3.Tap Control Center.

4.Tap Account Management.

From a desktop browser:

1.Log in to your Ring account at Ring.com.

2.Click the Dashboard home icon on the top right.

3.Click Account and select Control Center.

4.Click Account Management.

Updating your account details

Whenever you update information in your Ring account, we first require you to re-enter your password, and in most cases, enter your verification code. We’re just making sure it’s you who’s making these changes.

Changing your Name
You can change how your First Name and Last Name appear in your Ring account.

Updating your Email address
Did you recently change your email address? You can update it in Account Management.

Updating your Phone Number
If you recently changed your phone number, update it now in Account Management. Keep in mind, this is phone number we’ll contact if you dropped a call when speaking to our Customer Support Team. It may not be same number you provided to receive you sign-in verification codes.

Changing Your Name in Your Ring Account

Learn to update how your name appears in your Ring account.

Updating your Name

You can change or update your name in the Ring app or your account at Ring.com.

From the Ring app:

1.Open the Ring app.

2.Tap the menu (☰) and scroll down to Control Center.

3.Tap Account Management.

4.Under Name, tap Update.

5.You’ll be asked to re-enter your password.

6.You’ll then be asked to enter your sign-in code. Help me find my verification code.

7.Enter your updated First Name and Last Name.

8.Tap Save.

From your desktop or mobile browser:

1.Log in to your account at Ring.com.

◦ If you’re on desktop: tap the Dashboard home icon at the top, then Account.

◦ If you’re on mobile: tap the top menu (☰).

2.Scroll down to Control Center.

3.Click Account Management.

4.Under Name, click Update.

5.You’ll be asked to re-enter your password.

6.You’ll then be asked to enter your sign-in code. Help me find my verification code.

7.Enter your updated First Name and Last Name.

8.Click Save.

Account Verification in Control Center

Learn all the ways you can verify your account when signing in to Ring, or when speaking to Customer Support.

Get to know Account Verification

With Account Verification, you can choose how you want to receive your 6-digit verification code whenever you sign in to the Ring app or your account at Ring.com. We require you to enter this code, after you enter your password, to better protect your Ring account. This extra layer of security is called Two-Step Verification.

How to access Account Verification in Control Center.

From the Ring app:

1.Open the Ring app.

2.Tap the top menu (☰).

3.Tap Control Center.

4.Tap Account Verification.

From a mobile browser:

1.Log in to your Ring account at Ring.com.

2.Tap the top menu (☰).

3.Tap Control Center.

4.Tap Account Verification.

From a desktop browser:

1.Log in to your Ring account at Ring.com.

2.Click the Dashboard home icon on the top right.

3.Click Account and select Control Center.

4.Click Account Verification.

Choose a verification method

You have the option to choose how you want to receive your verification code, by Text Message or Authenticator App.

Text Message

When you choose Text Message as your verification method, you’ll receive a text to the mobile number you provide each time you sign in. Enter that code, and you’re in.
Learn how to get a verification code by text message

Authenticator App

Authenticator apps are security apps for your phone, tablet, and computer that help prove who you are. These apps generate 6-digit verification codes to help verify you when signing in to Ring.

Learn how to use an Authenticator App to sign in to Ring

Verification codes in Control Center

If you don’t have access to your text messages or your device’s authenticator app, you can generate a code from Control Center in Account Verification.
Learn more

Customer Support Verification

If you need to speak with our Customer Support Team, they may ask to verify it’s you. In Account Verification, you can generate code to give to the Support Associate to help verify your Ring account. We will NEVER ask you for your password.

Using the Ring Live View Widget

Learn how to add Live View widgets to your phone or tablet’s home screen.

Get to know Live View widgets

With Ring Live View widgets, you can access Live View on your Ring video doorbells and security cameras with just a tap, right from the home screen of your smartphone or tablet.

Ring Live View widgets appear as tiles on your home screen, with each widget displaying the name and image of a chosen device.

Make sure your Ring app and operating system are up to date.
Live View widgets are available with the Ring app versions 5.58 on iOS and 3.58 on Android. Confirm both your app version and mobile device’s operating system are up-to-date to use this feature.

How to set up a Live View widget

Apple iOS phones and tablets

For iOS, see Apple’s How to add and edit widgets on your iPhone article, or follow these steps:

1.Tap and hold the home screen and wait for the icons to start wiggling.

2.Tap the plus (+) icon that appears in the top left corner of the screen, then tap on Search Widgets and search “Ring”.

3.Select a device widget, tap Add widget, and place it wherever you’d like on your home screen.

Your Ring Live View widget will select one of your Ring devices by default. To choose a different device, follow the steps below on How to edit Ring Live View widgets.

Android OS phones and tablets

For Android, see Google’s Add apps, shortcuts & widgets to your Home screens article, or follow these steps:

1.Tap and hold an empty space on the home screen.

2.Tap Widgets and search for “Ring” (or press and hold on the Ring app, then select Widgets).

3.Press and hold on the widget you’d like to add, then drag and place it on the home screen of your choice.

4.Then, choose which Ring device you’d like to access from the widget.

How to edit Ring Live View widgets

1.Tap and hold the widget.

2.Tap Edit.

3.Choose a different doorbell or camera for instant Live View access.

4.Tap outside the widget to exit.

Note: If you want instant Live View access for multiple devices, you will need to add one Ring Live View widget per Ring device.

Adjusting the Volume on Ring Doorbells, Security Cameras and Chimes

Adjust the volume on your Ring Video Doorbell, Security Cameras, and Chime or Chime Pro to the sound level that’s right for you.

How to adjust the volume on your Video Doorbell

1.Tap on the menu (☰).

2.Tap Devices.

3.Tap your Video Doorbell.

4.Tap Device Settings.

5.Tap General Settings.

6.Tap Volume Settings.

◦ Two-Way Talk: Adjust the volume slider for Device Speaker.

◦ Doorbell press: Adjust the volume slider for Doorbell Sounds.

Important: Adjusting the volume for Two-Way Talk may not be available for all Ring devices.

How to adjust the volume on your Ring Security Camera

You can adjust the volume on the Floodlight Cam Wired Plus and Floodlight Cam Wired Pro.
Find out which Security Camera you have in the Ring app.

1.Tap on the menu (☰).

2.Tap Devices.

3.Select your Ring Security Camera.

4.Tap on Device Settings.

5.Tap on General Settings.

6.Tap on Volume Settings.

◦ Two-Way Talk: Adjust the volume slider for Device Speaker.

How to adjust the volume on your Ring Chime and Chime Pro

1.Tap on the menu (☰).

2.Tap Devices.

3.Select your Chime.

4.Tap Audio Settings.

5.Tap Chime Tones.

◦ Adjust the volume sliders under Rings and Motion.

Setting Audio Alerts on Chime and Chime Pro

Learn how to set Chime or Chime Pro to play sounds when events happen on Ring devices at the same location.

Chime Alerts are only available for devices at the same location.
Previously, Chime and Chime Pro devices could play sounds across multiple Ring device addresses. We’ve since improved this feature to give you more relevant Chime Alerts in the same location where Motion or Ring events occur.
Learn how to manage your Ring device locations

Wisenet WAVE User Guide

admin — Tue, 19 Sep 2023 18:41:01 +0000

Wisenet WAVE is an IP Video management platform that allows users to create IP video surveillance solutions tailored to any type of project, usable by anyone and on any device. It is simple to setup and use, yet a reliable VMS designed for you.Endlessly customize the IP Video Management platform to create tailored networked video solutions for any type of project, for use by anyone, on any device.

Wisenet WAVE User Manual

How to collect Wave Mobile logs for iOS

Summary:

When there are instances of abnormal behavior on the Wave Mobile applications. Support will ask for the collection of logs from the mobile device.

Step By Step Guide:

1. Open the Wave Mobile app

2. Click on the three horizontal lines in the upper left of the application

3. Click Disconnect from Server

4. Press and hold down on the version number for over ten seconds (Figure 1)

Figure 1

5. Click on Change Log Level (Figure 2)

6. Change the log level to Debug2 (Figure 2)

7. Change the minutes to 5 (Figure 2)

8. Click on Upload Logs Next (Figure 2)

Figure 2

9. A System ID will be copied to the clipboard (Figure 3)

10. Click the back arrow (Figure 3)

Figure 3

11. Reconnect to your system

12. Recreate the issue more than once for good logging

13. Close Wave Mobile and note the time

14. Update your support ticket with the System ID, and the time of the events

Why won’t Wisenet Viewer uninstall from my macOS

Summary:

The end-user has locked themselves out of their Wisenet Viewer, and you need to reinstall. But Viewer uninstallation does not clear out the credentials after uninstall.

Explanation of Behavior:

• On Windows or Linux-based systems, if a Wisenet Viewer user locks themselves out, they have to uninstall and re-install to get back in

• macOS keeps system files from Wisenet Viewer that store the software database.

Resolution:

• Open Finder

• Type Wisenet Viewer

• Click the “+” symbol to the right of Save (Figure 1)

Figure 1

• Select Other from the list (Figure 2)

Figure 2

• Find System Files in the list (Figure 3)

• Change to: are included (Figure 3)

• Click OK (Figure 3)

Figure 3

• The Search window should now have two results. The Application and the System Files (Figure 4)

• Drag both items to the trash (Figure 4)

Figure 4

• Re-install the Wisenet Viewer application

Why do Wave resources spike when I use API transcoding to a third party

Summary:

Transcoding is taking compressed or encoded content, decompressing or decoding it, modifying it somehow, and re-compressing or re-encoding it. The most common scenario is decreasing the resolution and bitrate/framerate. Sometimes this can include changing a video or audio format from one to another (e.g, MJPEG to H264), or adding watermarks to the video.

Note: Please be aware of the potential CPU overload. We don’t recommend
increasing this value unless your hardware is suitable for the task.

Explanation of Behavior:

• A transcoding session is one instance of this process, so when you need to transcode multiple things, you can have multiple sessions to transcode simultaneously

• This session is initiated when the GET/media/. API call is made with WEBM and MPJPEG format AND links with a custom resolution parameter

• Since Wave 4.0, a default limit has been put in place of no more than two simultaneous transcoding sessions.

• The two transcoding limits were put in place to avoid CPU overload issues often observed at sites with progressive download enabled

• As a result, this change may break some integrations which relied on more than two simultaneous transcoding sessions

Resolution:

• Administrator-level permissions are required to make the change

• Modify the following address and enter it into your browser:

<server_address>:/#/settings/advanced

• To increase this limit, on the advanced settings page, search for (See Figure 1)

Figure 1

• Modify the value of the maxHttpTranscodingSessions parameter

• Click Save to confirm your changes

• Restart the Wave server

How many Wave clients can connect to Wave Server?

Summary:

This article considers a max number of connections to a single Wave Server. In multi-Server systems, designers should consider the number of desktop clients and the number of devices available on each Server to avoid any potential bottlenecks.

Explanation of Behavior:

• The number of concurrent Desktop clients that can connect to any Wave Server is limited by the number of TCP connections a Server can support – for the Wave Server, that number is now 2000 concurrent TCP connections per Server.

• Practically speaking, to calculate the maximum number of Desktop client connections to a single Server in a System, you should use the metrics and formulas in the resolution section.

Resolution:

• Each Desktop client connecting to the Server = 5 TCP Connections

• Each Device being viewed in Desktop client = 1 TCP Connection

• Max Clients = 5 x (Total Number of Clients) + (Average # of Devices per Client x Total Number of Clients)

• Max Clients = 400 Desktop Clients w/ no displayed devices

• Max Clients = 80 Desktop Clients with an average of 20 devices displayed per client

• Max Clients = 28 Desktop Clients with 64 devices displayed per client

How to perform a silent install with the WAVE software.

Summary:

System administrators often prefer to deploy software via automatic methods to remove the need for a technician to visit each workstation, login, etc. A silent install assumes a method of pushing software already exists.

Step By Step Guide:

1. Download the appropriate WAVE software from wavevms.com.

2. Use the /S switch appended to the WAVE installation executable. This will force a silent installation without requiring any user interaction.

Example: wave-client-5.0.0.35270-windows_x64.exe /S

Note: Always test this process in a lab or test environment before deploying into a production
environment.

3. Use this command for deployment using your preferred software deployment method. Note that you may need administrator credentials for the installation.

To validate that the installation was successful, the user will see the WAVE client icon on their desktop and/or the WAVE server tray icon in the system tray.

How do I add a Wave Sync end user account?

Summary:

This article will walk you through creating Wave Sync end-user accounts.

NOTE: For attaching your server to the Wave Sync service, click >Here<

Step By Step Guide:

1. Log in to Wave as an admin

2. Right-click on Users (Figure 1)

3. Select New User (Figure 1)

Figure 1

4. Select Wave Sync (Figure 2)

5. Enter the end user’s email address (Figure 2)

6. Select the Role for this end-user(Figure 2)

7. Click OK (Figure 2)

Figure 2

8. The end-user will receive a confirmation email with a link to set the password on their Wave Sync account (Figure 3)

9. Click on the Orange link and set up the Wave Sync User account (Figure 3)

Figure 3

10. The end-user can now log in to Wave from a desktop pc or mobile application with their email as their username and their password set up via the link (Figure 3)

My camera streams are loading too slow, or just failing to load.

Summary:

If a Wave server is suffering abnormal performance issues or failing to load streams from a particular device. That device may be misconfigured in relation to Wave. Always check out our camera compatibility page to see is Wave supports the settings you have that particular camera or encoder streaming at.

NOTE: If your settings exceed what Wave has certified for proper function. Your
server will experience multiple resource issues.
This Article provides steps to resolve said resource issues.

Step By Step Guide:

1. Start by launching the Windows Resource Monitor (Figure 1)

Figure 1

2. Or the WAVE Monitoring (admins only) (Figure 2)

NOTE: This picture has the CPU on the high side

Figure 2

2. See If the Hanwha Media Server taxing the processor at 70% or higher in the Windows Resource Monitor.

Note: If the WAVE Media Server is using more resources, this is due to the
settings of the connected devices exceeding the recommended settings.
.

3. Use the IPVD Site to locate the third party or Hanwha devices, and their proper settings.

4. Type the model number in to the search window. Then select the model number of your device(s) in the search window.

5. When you select the proper model it will display the tested Resolution(max) and FPS(max) setting. Make sure the secondary stream resolution and the FPS(max) is the same or lower than the Resolution (max) FPS(max) (Figure 3)

Figure 3

6. These settings will need to be done in the third-party device user interface in most. cases.

7. Once these modification are done, please see If the Hanwha Media Server has lowered the percentage of the processor in the Windows Resource Monitor.

8. Please keep check if there is abnormal performance in Windows Resource Monitor on the server to see if there is anything out of the ordinary.

How to Reset my WAVE & Wave Sync Passwords?

Summary:

There will be times that require your password to be reset for WAVE and WAVE Sync. This article will cover the requirements and steps to reset your password.

Minimum Password Requirements:

In WISENET WAVE, there are minimum password security requirements for new passwords, including:

• It must be at least 8 characters

• Must contain at least two types of Symbols (e.g. lowercase + uppercase, lowercase + number, lowercase + special character)

• It must not match any of the 1000 most popular passwords (blacklist updated each release).

NOTE: Although WAVE does not allow users to modify the password requirements, users
who us LDAP/Active Directory integration can enforce their own password policy for their
own organization.

How to Reset your Password:

WAVE Sync connected systems:

1. Navigate to the built-in password reset function or click here (Figure 1)

Figure 1

Non-WAVE Sync Connected Systems:

1. Contact your System Owner, or System Admin can help them reset their password.

WAVE: Using NVR with WAVE – architecture

Wisenet WAVE is a software based on a server-client architecture (or you’ll also hear us refer to it as server-hive client architecture). This means that server functionality is required for a system to function.

The architectural framework remains the same when an embedded NVR is used with WAVE. An NVR needs to be registered to the WAVE server as a device and WAVE clients would connect to the WAVE server to receive video streams. A client machine cannot connect directly to the NVR to establish a connection.

Best Practice:

– It is recommended to have a dedicated computer to run a WAVE Server application. Because WAVE is such a light software, users may be tempted to install both the WAVE Server and WAVE Client on the same computer to run the system; however, this is not recommended. If multiple clients are connecting to the system to view NVR streams, the computer with the WAVE Server installed needs to be running all the time. If the computer with the WAVE Server is shut down for any reason, no one will be able to access the system.

Recommended Server specs when using an NVR:

– It is recommended to follow WAVE server specifications.

– The required server specifications will vary depending on the number of cameras, resolution of the camera streams, the number of connected clients, as well as the number of servers in the system.

– It is recommended to use at least an Intel i3 (9th Generation) or similar server or better.