.

Why add cameras to an NVR?​

.

Before you start…​

Before anything, to be able to add your IP cameras, you need to make sure that:
.

.

How to connect an IP camera to a Hikvision NVR 5

How to add your cameras using the V5 GUI…​

Step 1:​

Open a web browser and enter the IP address of your NVR in the address bar. If you are not sure what this is, use the SADP tool to find it.​

Step 2:​

Log in to the NVR using the “admin” username and password you have set on it.​

Step 3:​

Go to: Device Access > Device Configuration > PoE Settings​

​

If you are connecting your camera via the Plug-and-Play method, then make sure that Network Camera Plug-and-Play is enabled on the POE port you will be connecting the camera to on this page.​

​

For any camera with a cable run under 100m, leave the Network Cable Distance as Short Distance.​

​

If you are connecting your camera manually by IP address, disable the Network Camera Plug-and-Play option for the channel that you plan to add the camera to.​

Step 4:​

Go to: Device Access > Device > Video Device​

​

For any Plug-and-Play camera, just make sure that it is in its inactive default state and then connect it to the port you reserved in step 3. After 20 seconds or so, the camera Status should turn to Connecting and then Online (you may need to click on Refresh to see this).​

​

For Manually added cameras, if you can see the camera in the List of Online Devices section, then just tick the box for the camera and then click + Add to Device List, which will then automatically add it to one of the channels you disabled Plug-and-Play on in the last step.​

Alternatively…​

Click on +Add at the top of the page and fill out the fields as follows:​

​

IP Address: Enter the IP address of your camera, using the ‘Test’ button to verify there is a camera at that address. ​

Device Name: This can be anything you like, as it is the name the camera will show with on your NVR. ​

Protocol: Select the camera’s manufacturer from this list, or failing that, use the ONVIF protocol (your camera will need to have ONVIF enabled for this to work). ​

Management Port: Enter the Server port set on the camera, which you can find in the SADP tool or in Network>Basic Settings>Port in the camera’s web browser interface. If you haven’t changed this, it is usually 8000 by default. ​

User Name: “admin” or the username of any other users set up on that camera. ​

Password: The password set with that user on the camera – if this is the same as the ‘Default Activation Password‘ you have set on the NVR, then you can tick this box instead. ​

Transfer Protocol: ‘Auto’ is normally best. ​

​

When these are completed, click OK.​

​

Your camera should then appear in the list of devices with an assigned channel, and an Online status, meaning it has been successfully added.​

.

.

Extra tips…​

How do I reset my Hikvision device to factory settings?

In some cases, you’ll need to reset your Hikvision device to its inactive factory state. This could be if you’re passing the system on to somebody else; if you’ve forgotten your password; or simply if something has gone wrong during the configuration, meaning you need to start afresh.

There are a couple of ways of doing this, the method you’ll use depends on whether you have a password to log into the device.

Please see the simple steps for doing each below:

Via the device’s backend in a web browser or iVMS-4200:

If you are able to log into your device’s configuration menu in iVMS-4200 or the web browser interface, then the easiest way to reset it is on the Upgrade & Maintenance page here. The steps below show you how to find this page in both interfaces.

Step 1:

iVMS-4200:

In a web browser:

Step 2:

In both iVMS-4200 and a web browser:

Factory reset by using the device’s pushbutton:

On the majority of Hikvision’s newer camera models, there will be a pushbutton on the camera which will allow to carry out a hard reset without needing to log into it. This is most useful when you have forgotten your password, as it allows you to set a new password on the camera while avoiding much of the faff involved in doing this through the SADP tool.

Step 1:

​

Step 2:

1. Disconnect the camera’s power supply.
2. Press the reset button and keep it held down.
3. Restore the power supply while continuing to hold down the button.
4. Keep the button pressed for a further 10 seconds.
5. Release the button and wait for the camera to reboot.

.

The Optiview VMS supports IP/Megapixel cameras, Analog, HD-over-Coax and IP/Network recorders. Another aspect of this powerful system is the fact that the 64-channel preview screens can be opened in up to 4 windows for live viewing up to 256 channels at the same time.

While all cameras will record on their local recorders, the VMS allows for up to 16 channels to record locally on the home or work PC. 36 channels can be chosen for playback in increments of 24 hour periods.

.

SOFTWARE DOWNLOADS

Right-click and select “Save Link As”

OTHER DOWNLOADS

VMX SERIES SUPPORT

Downloads / Files / Support

Welcome to the comprehensive support page for the Optiview VMX video monitoring platform. This platform, offering both VMX and VMX+ versions, is a potent, integrated solution for single and multi-site surveillance and access control systems. Whether you’re a first-time user or seasoned expert, we’re committed to ensuring that your experience with the Optiview VMX platform is seamless. This page is your hub for downloading all the necessary software and related materials for the Optiview VMX system. As always, if you need more in depth support, call our US based text support line at 904.855.1121.

.

OPTIVIEW VMX

INTEGRATED MULTI-SITE MANAGEMENT SYSTEM

for Single and Multi-Site Surveillance and Access Control Systems

OVERVIEW

The Optiview VMX and VMX+ remote viewing platforms are both powerful, all-in-one professional, project level video surveillance management software. The Optiview VMX Client can be downloaded for free, and will support up to 64 network cameras and intercoms, and supports 1 user account. View up to 512 cameras and 256 Video Intercom devices, integrate multiple access control units, and access advanced analytics by upgrading to the Optiview VMX+.

The Optiview VMX/+ provides user rights management, device management, alarm management, video wall output, and two-way audio. In addition to these VMS features, Optiview VMX/+ offers advanced features, including support for real-time face recognition and robust event management controls.

FEATURES

SOFTWARE DOWNLOADS

OTHER DOWNLOADS

To view the product pages for Optiview VMX Free and VMX Plus click the link below:

Optiview VMX Free

Optiview VMX+

COMPATIBILITY

Optiview VMX is compatible with all Optiview IP-enabled devices: network cameras, NVRs, DVRs, video intercom devices, and access control devices. The server is also compatible with the ONVIF protocol, so it can connect to ONVIF-enabled third-party devices, such as some of Optiview’s third party manufacturers. Call your account managers to talk about our compatability matching.

PLAYBACK

The Optiview VMX platform allows for quick and easy playback of surveillance footage from both the Live footage interface, and the Playback interface. Users can search by time, date, or event type. Users can also zoom in on the timeline, and drag through the timeline with video scrubbing. Download multiple video files at a time, take single frame snapshots, or a ‘burst’ of snapshots.

SMART SEARCH

Search through your surveillance footage quickly and efficiently by using Smart Search, and targeting the area of the screen where motion would have occurred.

INSTANT PLAYBACK

Thought you saw something? Click “Instant Playback” for an immediate jump back in time to 30 seconds in the past to re-review your surveillance footage.

MULTI-MONITOR SUPPORT

Take advantage of complete multi-monitors support.

ADVANCED REPORTING

The Optiview VMX supports heat map, people counting, ANPR license plate capture, attendance and access control reporting.

FLEXIBLE & SCALABLE

Optiview VMX+ supports up to 512 video channels, which includes up to thirty two (32) face recognition cameras. Easily add multiple recorders, cameras, and access control devices from a single-site or from multiple locations around the world.

FISHEYE CAMERA SUPPORT

The software features full support for Optiview Fisheye cameras. The software supports options for the Fisheye camera installation and supports dewarping Optiview’s 360° panoramic fisheye cameras in both live view, and in playback. Because dewarp happens at the software level, the video is always recorded in full fisheye, even if the live view is being dewarped. This allows viewers to see the entire video, and dewarp sections of the video at any given time.

Fisheye

Fisheye Dewarp X4

Fisheye Dewarp X8

REAL-TIME FACE RECOGNITION

The Optiview VMX/+ performs real-time facial recognition on up to two (2) / thirty two (32) channels simultaneously. The software captures and analyzes facial features to determine gender, age, expression, glasses, mustache, and mask, and then can record the faces and store the associated structured data. The server also filters incoming video to display faces that match target features. Facial recognition requires a camera that supports this feature.

ACCESS CONTROL & VIDEO INTERCOM

Optiview VMX offers full support and integration for access control and video intercom products to support a complete security and surveillance system. The server monitors door status and events, manages access rights, and support advanced rules management. In addition to access controls, the server supports two-way communication between intercom and control center.

MANAGEMENT OPERATIONS

The software manages the devices and the user accounts for an entire organization. Operators can assign different camera ranges, active use periods, and business roles for each user. The server also supports different schemes for various events, including IVS, to record and view all event history information.

VISITORS

Quickly register and customize access for visitors.

LPR

Capture license plates in a searchable database.

EMAP

Easily select cameras to view on map.

USERS

Create up to 100 Users per VMX Server.

EVENTS

Track entrance / exit, alarms, access, and more.

.

FREQUENTLY ASKED QUESTIONS

WHAT ARE THE MAJOR DIFFERENCES BETWEEN THE VMS AND THE VMX?

The Optiview VMS and the Optiview VMX are both multi-site remote monitoring software that can be used to view cameras and devices from a centralized location. The VMS is ideal for residential and commercial use, where basic camera surveillance is the primary need. The VMX, however, has an advanced access control module, and can support advanced surveillance such as facial recognition, traffic density, ANPR license plate database capture, and more. See which software is right for you here!

WHY DO I HAVE TO START USING THE VMX?

The free Optiview Video Management Software (VMS) is our legacy remote viewing software, and will no longer be supported going forward. Instead, download our all new Optiview VMX, our powerful new remote viewing software; The user is able to choose between a free VMX, and a more advanced VMX+ with additional features. The new VMX and VMX+ provide a more stable management and viewing platform for CCTV and Access Control, as well as providing many new features. Not sure which solution is right for you? Contact an Optiview Account Manager or compare the Optiview VMX and VMX+ here.

Features Gained:

Optiview’s VMX will support Optiview legacy equipment as well as the latest in megapixel, analytic, and edge recording technology.

WHAT IS THE DIFFERENCE BETWEEN THE FREE VMX AND PAID VMX+ VERSION?

The free version of the Optiview VMX supports 64 video channels, 2 ANPR channels, 2 facial recognition channels, 64 access control channels, 2 POS channels, 4 attendance devices, 2 alarms, and supports only 1 online user at a time.

The paid version allows the user up to a maximum of 512 video channels, 200 access control devices, 1024 doors, 32 video intercom devices, 32 facial recognition cameras, 100 alarms, 32 license plate capture cameras, and supports up to 100 online users.

See which software is right for you here!

WHEN WILL THE VMS STOP BEING SUPPORTED AND AVAILABLE?

The Optiview VMS 2018 will continue to be available to download for a limited amount of time, but will no longer be supported going forward.

WHAT IS THE MAXIMUM NUMBER OF DEVICES THAT CAN BE PUT ON THE FREE VMX OR THE PAID VMX+?

The free version of the Optiview VMX will suport up to 64 cameras. If the user wants to view more than 64 cameras, they will have to purchase the Base License, and then an additional license for each channel, up to 512. See which software is right for you here!

HOW DO I UPGRADE FROM THE VMS TO THE VMX?

The VMX software is completely different from the Optiview VMS and a user can use both. The VMX Server and Client software can be downloaded here.

WHAT IS THE DIFFERENCE BETWEEN THE VMX SERVER AND THE VMX CLIENT?

The server runs all the services and acts as a connection point for several clients that will handle the management of configurations, devices and integrations of one or more IP devices supported by the Optiview VMX software.

IF I HAVE THE SERVER DOWNLOADED, HOW DO I DOWNLOAD THE CLIENT?

The client can be downloaded using the link from the server user interface labeled as “Download Client”. I also made a link for the Client software within our technical support page which Georgia can use, to make a download link within the product resource page.

CAN I DESIGNATE THE NUMBER OF CAMERA CHANNELS BEING SEEN BY THE VMX PER DVR OR NVR?

Yes. The number of cameras “actually” in use by a device (for example a 32-ch NVR) can be designated within the VMX so that it can only sees the actual number of channels. For example, If a user is using multiple 32 channel recorders but not all channels, the VMX can be set to not count every single channel and maximize the usage.

CAN I DESIGNATE THE NUMBER OF ACCESS CONTROL DOORS BEING SEEN BY THE VMX?

No. Whatever the maximum number of doors that an access control panel can handle is, that is what the VMX will see. For example, a CAS-4MC (4 door master control panel) is expandable up to 64 doors, so this will max out the VMX. No additional master control panels can be added unless the user upgrades to the paid version of the Optiview VMX.

CAN I SEE THE HUMAN TEMPERATURE DETECTION & NOTIFICATION SOLUTION ON THE VMX?

The human temperature text overlay can be seen at LIVE mode and Playback mode at the VMX.

HOW MANY USERS CAN ACCESS THE VMX AT ONE TIME?

For the FREE version, only 1 user can access the VMX at any given time, regardless of how many clients are downloaded. With the paid version, up to 100 active users are able to access the VMX Server at any given time via multiple clients. See which software is right for you here!

.

 .

What is DMSS APP?

DMSS is a mobile surveillance app with functions like video playback, remote monitoring, device initialization, push notifications, and remote configuration. Devices like IPC, NVR, XVR, VTO, doorbells, alarms and access controllers can be added. After logging into the account, you can use cloud services like cloud upgrade and so on. The app supports iOS 9.0 and Android 5.0 or later systems and can be used with 3G/4G/Wi-Fi.

 .

What are the benefits of DMSS Camera App?

Remote operations

Before talking about DMSS Camera application on Alexa, let’s see what is DMSS? DMSS app can work in an environment with various internet connections. It connects Dahua CCTV products through both Internet and Ethernet. P2P-enabled internet connection shows great simplicity, while IP or domain name-enabled Ethernet connection guarantees strong stability.

DMSS can be operated remotely to immediately and stably control specific devices all around the world through its global network coverage. many functions including PTZ controlling, video preview and playback, video image adjustment (such as White Balance, focus, etc.), alarm subscription, voice intercom and etc. can be done remotely.

 .

increased data security

DMSS adopts multiple layers of data encryption protection to supply better data security to users.

From a product to the platform and then to the mobile client, DMSS uses multiple layers of data encryption protection to provide better data security to users. DMSS camera has also been certified by TÜV Rheinland, meaning the product complies with the GDPR and meets the TÜV Rheinland 2PfG 2624/06.17 standards, offering state-of-the-art information security and privacy protection.

Featuring a more detailed interaction design, DMSS provides a smoother user experience.

 .

Supports thermal products

To prepare the best support for the global efforts in pandemic prevention and control, DMSS CCTV also supports thermal products (supported by CCTV Suppliers), including access control, thermal cameras, and temperature monitoring terminals. It lets the operators control thermal products remotely and perform their duty in a safer manner.

 .

Setup DMSS App on Alexa amazon

Amazon Alexa is a virtual assistant AI technology developed by Amazon. It is able to voice interaction, music playback, make to-do lists, stream podcasts, set alarms, play audiobooks, and provide weather, traffic, sports, and other real-time information, such as news. Using itself as a home automation system, Alexa can also control your home security camera and even we can set up DMSS application on Alexa. Users are able to increase the Alexa capabilities by installing “skills” (additional functionality developed by third-party vendors, in other settings more commonly called apps) like weather programs and audio features.

Most devices with Alexa let users activate the device using a wake-word (like Alexa or Amazon); other devices (like the Amazon mobile app on iOS or Android and Amazon Dash Wand) require the user to click a button to activate Alexa’s listening mode, although, some phones also let a user say a command, such as “Alexa” or “Alexa wake”.

In September 2019, Amazon launched many new devices achieving many records while competing with the world’s smart home industry. The new Echo Studio became the first smart speaker with 360 sound and Dolby sound. Other new devices included an Echo dot with a clock behind the fabric, a new third-generation Amazon Echo, Echo Show 8, a plug-in Echo device, Echo Flex, Alexa built-in wireless earphones, Echo buds, Alexa built-in spectacles, Echo frames, and Alexa built-in Ring, and Echo Loop.

How to use Alexa for your home security camera?

Using Alexa with a home security camera adds comfort. You can use a smart display screen in your house to immediately and easily review past footage and see who’s at the door right now. Just make sure you have compatible devices and you’ll be using Alexa to check in on your camera (or cameras) in no time. One of the utilities of Alexa is setting up the DMSS application on Alexa. Let’s we how we can do it.

 .

DMSS application on Alexa: How does Alexa work with DMSS?

To add your Dahua device using the Amazon Alexa app:

Let’s assume that you’ve installed and configured your Alexa-compatible home security camera already and you have an Alexa-enabled smart speaker.

Now you need to log in to your Alexa app or make an account if you don’t already have one. Simply download the Alexa app and follow the prompts to sign in/register a new account.

Open the Alexa app and choose “Skills & Games” in the menu. Type “Ring” in the search box, open the skill, and choose “Enable.”

You’ll be asked to enter your Ring account credentials to pair your Ring account to the Alexa app.

 .

How to Download the DMSS Application?

The prefix “g” or “i” differentiate the applications intended for Android and iPhone/iPad and thus we will find them in the official Google Play and App Store:

Before, DMSS Plus was paid while you could get the Lite version for free. There are some differences between DMSS Lite and Plus such as E-Map (visual and functional installation plans), alarm management, and push notifications. Currently, there is no need to choose since Dahua has released the Plus version for free. In addition, this publication is already adapted to the new GDPR (General Data Protection Regulation).

 .

 .

Download Dahua DMSS software

View DMSS APP User Manual

 .

What Functions Do These Apps Offer?

The aforementioned applications have undergone several updates that improve their operation and increase their capabilities so sometimes it is difficult to follow all the news. Therefore, let’s see a summary of what they offer us for the management of our video surveillance devices:

Integration of Other Security Devices

The main novelty is managing DMSS CCTV devices, access control devices, and alarm systems from the manufacturer Dahua in a single app.

 .

Device Management

Among other options, they can be located within a local network (WiFi or LAN), and add devices via IP/Domain, DDNS, and P2P (Easy4IP and Lechange). This last option allows you to add devices by scanning the QR code and even a complete list of devices, very useful for migrating from the Lite app to the Plus version in a single operation.

 .

Live View and Playback of Recordings and Stored Clips

Live, to access and capture live video from added devices, combining channels and cameras. Playback, to consult, capture, cut, and extract the recorded videos. In addition to that, clips and captures can be viewed from the smartphone’s memory.

 .

Channel Configuration

It allows you to modify the coding (image resolution and ratio), image adjustments, PTZ or motorized zoom camera movement control, two-way audio communication with the device, and quadrant display, as more interesting functions.

 .

Notifications and Events

Detection events generated by devices are listed and notified in the app through push notifications. These consist of instant and free alerts supported by the devices and to which we can easily subscribe, depending on the type of detection selected.

 .

Cloud Recording, Cloud Storage Services

Upcoming updates will enable cloud video recording under a subscription service, with per-channel rates for 3, 7, or 30-day recording, and only for cameras that support such functionality.

 .

You can also check:

Best CCTV Brands in the UK

 .

 .

How to See Your Dahua DMSS Security Cameras from the Cell Phone

DMSS is Dahua ‘s free software to connect to your equipment from smartphones. It is used to connect to all current Dahua manufacturer equipment: DVR recorders, HDCVI, NVRs, IP cameras, etc.

This App can be downloaded for free in both the Play Store and the App Store. The Android version is called gDMSS and the iPhone iOS version is called iDMSS.

To connect your Dahua device via P2P on your cell phone, you are going to need:

 .

How to Configure Your Dahua Security Cameras in DMSS

Enter the SN of the device and touch the “Next” button.

Once all the boxes are completed, tap the “Save” button that is located at the top right.

If you followed the steps correctly, it should start viewing your security cameras live. By tapping the back button at the top left, you can return to Start.

 .

How to View Your Dahua Cameras in DMSS

If you followed the steps correctly, you should start viewing your security cameras live.

 .

 .

 .

The red numbered buttons:

 .

The Yellow numbered buttons:

 .

 .

Conclusion

As we saw, you know about DMSS App & can set up Alexa on your camera easily, just you need to go to the menu and tap Skills. Find the relevant skill (some cameras have specific apps for the cameras, outside of their main smart home apps). Enable the skill and link the account with Alexa. It’s a simple thing to set up and it means that you can create a security monitor without ever firing up your smartphone or tablet. All you need is one of the three Amazon devices noted in the intro and a compatible DMSS camera.

.

1.Download the mobile APP (Guard Viewer) and Sign up

for an Account

Download the mobile APP and Sign up for an Account

1. Download and install the app.

Please scan the QR code to download the free APP “Guard Viewer”

You also can visit the Apple Store or the Google Play Store to download the Guard Viewer app for iOS or Android devices. Alter installation, tap the icon to launch the app.

2.Register an account and login

For first time use, please create a new account and add the following steps:

Please tap Sign up and follow the on-screen prompt to register an account by email.

2.Add Device to APP(Guard Viewer)

Guard Viewer Security System User Guide v1

Further support, plz email us at email love@hiseeu.com

Or contact us at +1 917 688 2228

Add Device to APP(Guard Viewer)

Auto add is not suggested. Please tap on “Later” if you see this message box.

In this situation, it will Auto Search to discover the NVR device connected to the local network. But once your mobile phone disconnects with LAN WiFi, you will not be able to view it anymore.

Please Add devices in this way

1.  Please Tap on  “ Menu” icon> Tap on “Devices”> “Add” ,

2.  Tap on “Scan”> “OK ” to scan the NVR QR code

3.Navigate to “Menu– Network> Basic> P2P”

• If the Device Status is “Network connected…” , means device is online   and ready for remote view

• If the Device Status is “Offline” , please check the network connection first, if the problem remains, please feel free to contact us at  Love@Hiseeu.com   

After you add the device successful, the “Device status” will be “Online”, and your APP account username will display here.   • You can check your APP user name by navigate to “Me”

• If the username doesn’t belong to you, please click on “Delete” and add it again.

4. add NVR by scanning device QR code and click on “save”

5.    Please Tap on “Menu ” icon, Tap on “Live View” “Add”

6.  Select the device and tap on “Start Live View ”

3.Device shows “Offline” (system kit to app)

Device shows “Offline” (system kit to app)

1. If the device shows offline on the mobile phone app, we need to make sure the NVR is connected to the network perfectly or not

2. Go to your monitor that is connected to NVR, and check out the network status first navigate to this path first: “Menu–Network–Basic–P2P”, also check whether the device status is online or not,

3. Also go to “Menu–Network–Advanced”,to disable the “PPPoE”

4. if it shows: network disconnected, plz enable the DHCP in this path ” Menu–Network–Basic-TCP/IP ” and click “Apply”. After that, go back to “P2P” and check if the device status is online or not

5. if you connect the network cable to the lan port or the lan/wan port of the router

We need to connect it to the lan port of the router,plz take a photo of yours for us to check.

.

If the P2P show connect the network ,but the app also show the offline,please delect the device on your APP and re-add it again.

4.Enable push alerts on APP

Enable push alerts on APP

5.Why I can’t remote view when the network is outside？

Why I can’t remote view when the network is outside？

.

Cause: Customer doesn’t follow the instructions on the user manual and add the device in a local adding way, so we suggest them to delete the device first, and re-add the device again like this FAQ

https://www.hiseeu.com/a/help/article/53969

6.APP Share Device

APP Share Device

One device is linked to one user only. The NVR system can only be controlled by one authorized account, which can share the device with others to prevent attack or hacking.

There are 2 ways to share the device with others. For the admin user, please follow the instructions to share the device:

1.Type in “Menu Icon ” and navigate to “Devices”

2. Tape on “… ” > “Share”, You can select a single channel to share or select the entire NVR system to share

3.Share the device by typing in the user name you want to share and selecting the function as needed.

• The other user needs to register a Guard Viewer APP account and provide the user name for sharing.

• After that, when this user login the APP will find the device by navigating to “Devices”.

4.Share the device by generating a QR code

• Create a sharing password and set the valid period

• Click “Generate”, your APP will generate a QR code

• Other users can use the APP to add the device by scanning the QR code you sent

7.Add Device on Guard Station PC Client Software

Add Device on Guard Station PC Client Software

Add device to “Guard Station” Download link: https://www.dropbox.com/sh/jeftu4sqwy4y1u8/AAD4PkyEJxg6j4H1n20PxBkZa?dl=0  

Please sign up for the mobile APP(Guard Viewer) account and add the device first.

Download and run “Guard Station” on the PC

1) Please Navigate to “Device Management”> “Cloud Device”> Click on “Login”

2) Login with your APP account and password.

3) After Login, the device you added to the APP will list here

Please click on “Control Panel”> “Live View”> Double-Click Camera to load the live view video

8.Guard Station shows “offline”

Guard Station shows “offline”

plz check local NVR is connected to network perfectly or not,If your NVR hasn’t connected to the network yet, it will show “offline” in your PC Client “Guard Station”

Plz go to your NVR that is connected to Monitor,

Check out the network status, first navigate to this path first : “Menu–Network–Basic–P2P” ,and check the device status is online or not,

if it shows: network disconnected, plz enable the DHCP in this path ” Menu–Network–Basic-TCP/IP ” and click “Apply” , After that, go back to “P2P” and check if the device status is online or not

9.Not Recording? HDD not working?

Not Recording? HDD not working?

Right-click the mouse from “Menu–Storage–Hard Disk”

If there is no hard drive information or Status shows Abnormal, the hard drive is having an issue

10.AHD5 Modify the Camera model

AHD5 Modify the Camera model

（Please notice that AHD5 cameras only the TVI camera model have the audio function，the AHD5 cameras we sell seperately is the AHD model so it should modify the TVI model to have the audio function)

1. Click the OSD Menu Control , then click the arrows to the Menu t hen click the icon to select the “VIDEO SETTING ”

2.Select the VDEO SETTING and click the arrow to enter.

3.Then Select the “TVI ” on the HD, then click the “APPLY&REBOOT “and then click the “RETURN “and the “EXlT” back to the Version

4.Finally Turn Audio On

11.Forget DVR Password

Forget DVR Password

If you forget your current password, please follow the instructions to reset it.

1. In the system login interface, please click on “Enter Password” > “Forgot Password”

2. If you filled in your email address as a reserved email when you set up the system, you can reset the device password via the APP(Guard Viewer)

In NVR interface, tap forgot password.

1. Scan the above QR code by APP “ME–General–Forget Device Password” , and the security code will be sent to your email address.

2. If you haven’t set up an email before, or have any difficulties resetting the password, please take a screenshot of this interface(Serial No. please also make the code is as clear as you can ), and email us at love@hiseeu.com , since we need the serial number to produce a new password by using an internal tool

12.One or two cameras are not working

One or two cameras are not wokring

(1) BNC Cable connected to Camera is broken

Step: Use another BNC cable to connect the camera to have a try

(2) The port of the DVR box is broken

Step: After changing the BNC cable, and still there is no camera image, plz insert the camera into another port of the DVR to have a try

(3) Camera is broken after troubleshooting with the steps （1）-（2）

13.Four cameras or above are not working

Four cameras or above are not working

Four cameras or above not working is an abnormal situation. It’s not only a camera issue, which could be related to a power supply or power splitter connected to four cameras

If the power supply or power splitter connected to four cameras is broken, which can’t provide power supply to cameras

Step:

(1）Change to another 12V 2A Power Supply to connect to four cameras to have a try. We wanna make sure if this is related to the power adapter

(2) Change another 1-4 way power splitter to connect four cameras to have a try. We wanna make sure if this is related to the power adapter

( If you do not have another power adapter/splitter, plz use the other power adapter connected to the four normal cameras)

After making sure the power supply or power splitter is doing fine, but still no camera image, which means the DVR box is having issue

4.Eight Cameras are not working

Eight Cameras are not working

Please check your camera connection is correct ， if the connection is correct ，

i t’s mostly possible the DVR box is having issue, and need a new DVR box replacement

Further support, plz email us at email love@hiseeu.com

Or contact us at +1 917 688 2228

15.How to record the event only？

How to record the event only ？

Please click the mouse to the Menu then click the “ Storage ” and then click the “ Recording Schedule ”，“ Select Camera ” then click the “ enable Schedule ” click the “ Audio Storage ” then select the color of record type and fill in the corresponding time and date.

.

Network Setup for NVR/DVR/IP Camera before adding to Guarding Vision

The Following network settings must be checked before adding the device to Guarding vision App.

Method 1: From NVR Local menu

Step 1: Right Click on the NVR Monitor and select “Menu”.

Step 2: Select “Configuration” from the Menu options.

Step 3: Select “Network” and check the option “Enable DHCP” Click “Apply”

Step 4: Make sure your NVR/DVR obtained an “IPV4 Address” and “Preferred DNS Server” values automatically. If not, check your network settings and make sure your device is properly connected to your network router or switch.

Step 5: Select “Platform Access” and check “Enable”.  You will be taken to the service terms window.

Step 6: Create a “Verification Code” check the “Guarding Vision service terms” click “OK”.

Step 7: Click “Apply” to apply the settings. The status will change to “Online”. The QR Code being displayed on your device “Platform Access” page can be scanned with Guarding Vision app to add the device into your App. To proceed with adding the device into the app scroll down to “Adding NVR/DVR to Guarding Vision App”.

Method 2: From the NVR/DVR/IP Camera Web page.

Step 1: Input the IP address of the NVR into the address bar and login with the credentials.

Step 2: Go to Configuration  Network  Basic Settings

Adding the NVR/DVR to Guarding Vision App

Method 1: Using the QR Code

Download and install the Guarding vision app on the Mobile. Register and Create a Guarding vision account on the App.

.

.

.

Step 1: Tap on the “+” to add a new device. Select “Scan QR Code”. Scan the QR Code displayed on the NVR’s Monitor.
.

.

.

.

.

.

Step 3: Scan the QR code from the device sticker or Login to the device Local Menu and go to Menu  Configuration  Network  Platform Access to access the QR Code.
.

.

.

.

.

.

.

.

Method 2: Add Device with Serial Number
.

(Only the last 9 digits of the serial number are needed to add the device into the App.)
.

Step 1: Tap on the ‘+’ icon and select “Manual Adding”
.

.

.

.

Step 2: The serial number can be accessed from the device sticker. To access the serial number from the web config, go to Configuration  System  System Settings  Basic Information
.

(Refer to the figure below)
.

Step 3: Once the “Manual Adding” Option is selected, You will be directed to the Add device page with “Serial No.” Input the serial number and click on  to save.

.

.

.

Step 4: Click “Add” to add the Device.
.

.

.

.

.

Step 5: Input the Verification Code that was created and click “OK”.
.

(You can find the code from the device web Config. Go to Configuration  Network  Advanced settings  Platform Access.)
.

.

Step 6: Tap on “Next”. Create a Device name in the “Edit Alias” page. Tap “Save”
.

.

.

.

.

.

Step 7: Tap on “Guarding Vision” at the bottom of the app to see your device listed. Tap on the device name to view the cameras connected to the device.
.

.

.

.

.

.

How to Change Camera names on the App
.

• Slide the device name to the left to view the settings and share icons.

• Tap on the  Settings icon.

• Tap on “Linked Camera”

.

• Click on the Edit icon and input a desired name to the camera and Tap “Save” icon.

• 

Guarding vision Setup from browser (www guardingvision com)

.

Step 1: Open browser (Internet explorer/Chrome) and input the address www.guardingvision.com. And click on “Register” to register for a new account.

Step 2: In the registration page, input the mandatory credentials and select “Email” for registering with email or “Country Code” for registering by a phone number.

Step 3: Once the account is created, select “Device Management” and select “Add” to add a new device.

Step 4: In the “Add Device” pop-up window, input the device serial number (Last 9 digits of the serial number found on the device sticker) and click on “Search”.

Step 5: If the platform access is enabled on the device, then you should see the device on the “Add device” window. Click on the ‘+’ icon for the device. Click on the link for Enabling “Platform Access” https://app.box.com/s/ftj2keo6pvvvkpif9ukquyp7jrvhktwx.

Step 6: Enter the verification code found on the platform access page of the device. Click “Add”.

.

Step 7: Click “OK”. Now the device should be added into the Guarding vision account. To view video stream, download the Guarding vision ass on your mobile phone and login with the account credentials just created.

.

.

Sharing the device:

To share the device with another Guarding vision account, click on the “Share” icon next to the device name

Select “Email” for sharing by email or select “Mobile Phone Number” to share by mobile number. Click on the check mark next to the device and click “Share”.

.

Initialize/Setup SD Card from Guarding Vision App

SD Card Setup for IP Camera from Guarding Vision

.

Purpose:

This document provides instructions on how to initialize a brand new SD card that is inserted into the IP Camera.

(Note: When a brand new SD Card is inserted into a IP Camera, it has to be initialized/formatted before it can start recording data)

.

Steps to Initialize/Format the SD card

Step 1: Open the app, Select ‘Guarding Vision’ on the bottom left and slide the device name to the left and select the icon.

Step 2: Once in the device settings page select ‘Storage Status’

.

.

.

.

Step 3: In the storage status page, select ‘Memory Card’, which will take you to the ‘Initialize Storage’ page.

.

.

.

.

Step 4: In the initialize storage page, select Initialize. This will format or initialize the sd card and the sd card should be ready for recording.

.

Reset device with Guarding Vision

Reset NVR using Guarding Vision

Purpose:

The purpose of this document is to be able to reset an NVR with the vuarding vision account.

Currently Supported HINO devices:

NVR532P16-I4

NVR516P16-I4

NVR732-I8

NVR764-I8

Required Firmware:

V4.1.65 or above

Initial setup for enabling Password reset from Guarding Vision

Step 1: During the initial device setup, make sure the “Reserved Email Settings” option is checked.

.

.

.

Step 2: Since the Reserved email settings option is enabled, the following screen as shown in the figure below should appear. Input the email that you wish to receive a password reset verification code.

(Note: Please enter a valid email)

.

.

.

Resetting password from the Guarding Vision App

Step 1: On the NVR login screen, click on “Forgot Password”

Step 2: On the following screen as shown in figure below, select “Verify by Reserved Email” and click “OK”

Step 3: You will be brought to a screen with QR Code.

.

.

Step 4: Open the Guarding vision App on your phone and go to More  Reset Device Password.

.

.

.

Step 5: Scan the QR Code shown on the NVR screen. You should see a message as shown in the figure below.

Step 6: Check your email to find the verification code and enter the code in the field provided and click on “OK”.

.

Platform Access for Guarding Vision Offilne Issue

Guarding Vision Offline Issue

Purpose:

This document provides steps to fix the Platform Access “Offline” status issue on your NVR/DVR.

Solution:

The most common cause for “Offline” status is when the “Preferred DNS Server” space is empty. Follow the steps below to fix this issue.

NVR Local menu

Step 1: On the monitor connected to the NVR, Right click and go to Menu  Configuration  Network  General

Step 2: Enter the “Preferred DNS server” address as 8.8.8.8

(Note: If “Enable DHCP” is checked, you can check the option “Enable DNS DHCP” which will let the NVR/DVR pullup its own Preferred DNS Server)

Step 3: Click “Apply”. The device might take a few seconds before applying the new values.

Step 4: Now go to Menu  Configuration  Network  Platform Access. The status should show “Online”. The device might take up to 60 sec before showing the new status. Click “Back” wait 60 sec and check the status again.

(Note: You can scan the QR code on your “Platform Access” page to add the device directly to your Guarding Vision App.)

.

Guarding Vision Quick Setup

Guarding Vision Setup Instructions

Setting up the DVR/NVR

Step 1: On the DVR/NVR screen, right click Select Menu  Configuration  Network.

Step 2: Under “General” input the “Preferred DNS Server” as 8.8.8.8 as shown in the figure below.(If you have “Enable DHCP” and “Enable DNS DHCP” option on this page selected, then you do not have to perform this step)

Step 3: Select “Platform Access” and check “Enable” and create a verification code. Click “Apply”.

.

(Note: The QR code displayed on the platform access page can be used to add the device into the guarding vision app.)

Adding the device on Guarding Vision App.

Step 1: Tap on the “+” to add a new device. Select “Scan QR Code” to scan the QR code being displayed on the NVR monitor. Input the Verification Code that was created under “Platform Access” in the NVR.

.

.

.

.

Step 3: For Manual Adding, input the “Serial No”. For QR code, Scan the QR code from the device sticker or the QR code displayed on the NVR. (Note: You can also scan the QR Code you see on the monitor. Refer to Step 3)

.

Guarding vision sharing and registering

Guarding Vision ‘Register’ ‘Login’ and ‘Share’

Registering on Guarding vision

.

Option 1: Tap on the “register” option. Now in the Register page enter the Mobile Phone number and tap on “Get Security Code”. You will receive a code by “Text”. Input the code you just received and complete the process.

Option 2: Tap on “Register by Email Address” for registering by email. You will receive the security code to the email address entered.

.

How to select Login options on Guarding vision

.

To Login using a mobile number, tap on the “Login by Mobile Phone Number” option. Now input the phone number and password and tap “Login”.

.

.

.

.

Sharing a device on Guarding vision

​

Method 1: Sharing from the Primary account

On the Primary account, swipe the device name to the left to access the “Share” Icon. Tap on the Share icon. This will take you to the “Recipient” page.

In the “Recipient” page enter the email or phone number of the user you want to share the device.

When sharing, make sure the Phone number/email/username are entered as shown in the account details.

Finding Account Details:

On the bottom of the app, Tap on “More” and select “Account Management” to view the Account details like Username, Email address(if used to register) and Mobile Phone Number (If used to register).

.

.

.

Add Stand alone device to Guarding Vision

.

Adding a Stand Alone IP Camera to Guarding Vision App

Step 1: Log in to the IP Camera with internet explorer and Go to Configuration  Network  Advanced Settings  Platform Access

Step 2: Check the “Enable Option” you will see a pop-up window asking to create a verification code. Enter the desired verification code and click “OK”

Step 3: You can view the verification code by clicking on the eye lid icon.

Step 4: Click “Save” and refresh the page. The status should turn from offline to online.

.

Step 5: Now you can add the device into guarding vision by entering the las 9 digits of the serial number which can be viewed by going in to

Configuration  System  System Settings.

.

Step 6: Open the guarding vision app on your mobile device and register for a new account.

Step 7: Click on the ‘+’ sign on the top right corner of the app and select manual add for serial number or QR code to scan the QR code on the device sticker

(Note: Playback can be viewed on the App for IP Cameras that support Micro SD Card)

.

Add Device with Static IP into Guarding Vision for Local Access

.

Add IP Camera to Guarding Vision with Static IP Address

Purpose: This document provides instructions on how to find and add a IP camera with static IP address into the Guarding Vision App.

Note:

Method 1: Adding an online device in the local network

Step 1: Open Guarding vision App and select “Guarding Vision” on the bottom of the App. Click on the “+” icon on the top right to access adding menu.

Step 2: From the Add menu, select “Online Device”

.

.

.

.

Step 3: In the online device list, tap the device you want to add. You will be taken to a details page.

Step 4: The details page shows you the info of the device that you just selected.

(Note: Select the “Add Device to Guarding Vision Server” option available under the “Add” button for remote access over cloud. For this, the device should be connected to the network and  the “Platform Access” option should be enabled from the local menu/web menu for NVR/DVR. For a IP Camera, the “Platform Access” should be enabled from the web menu.)

.

.

.

.

Step 4: in the “Add Device” page, input the Username and Password for the device and click  on  icon on the top right corner to save the login credentials and finish adding the device.

The device should be added to your App.

.

.

.

.

.

Method 2: Manual Adding option

(Note: Using this method, you can add a portforwarded device with a public IP address.)

Step1: Open the App and click on the “+” icon on the top right to access the add menu. Select “Manual Adding”.

Step 2: Select “IP/Domain” to change the adding type.

.

Step 3: Create a name for the device by typing in the “Alias” option.

• Input the “IP address” of the device and the login Credentials. Tap on  icon on the top right to save the values entered.

(Note: If you have a device with a port forwarded IP address, you can enter that public IP address in the address space with the device login credentials.)

.

.

The tool allows adding and monitoring a large number of cameras simultaneously. The cameras in your network can be automatically found and installed. The program supports IP and P2P connection modes as well as UMSP, HZXM, and HZZN protocols. It could also be necessary to provide the camera’s password to access it. After this step, the devices can be organized by grouping them into different folders. For monitoring purposes, it is possible to divide the workspace into up to 64 regions. Moreover, on the left, there is a panel, from which you can control the selected camera.

In addition to allowing the users to view live video streams, the program also lets you schedule recording sessions and play them later. Likewise, it can take snapshots of specific video frames. Moreover, you can implement alarms to send notifications to a given SMS number.

All in all, QmEye is an excellent solution in terms of the number of cameras and connection protocols allowed. Unfortunately, the tool is not as easy to use as other similar tools and its graphical user interface probably needs a redesign.

This manual has mainly instructions on the installation and usage in Android, iPhone mobile phone.

1.Android

This cloud service platform is the best mobile phone video during the internet era. It consists of front-end acquisition devices, platform servers, and remote view of three parts.

Open the software into the login interface, inputting the username and password and click button “login”, then it will be login the application.

Icon description：

Notice: Please click “LoginFree”, directly into the system, without verifying user name and password. And you can get help information without login.
1.1 User register
User register

Click the button “register” on the login menu, then will jump to the register interface.

Enter the register information, click “register” then will be registered.
Note:1 please enter the valid E-mail address in order to retrieve your password when you lost it.

2 No account login version, no such function! 

retrieve the password

On the register clicking the button “login” and jump to “retrieve password” interface.

Input the username, click button “retrieve password”.

If you have entered your name and email address when registering and the username has been occupied, then “retrieve password” information will be sent to the email address.

QMeye User Manual 2024

1.2 Real-time preview

In the main menu, clicking “real-time preview
Click “Favorites” button, go to “collection management” interface

Click on the icon, favorites list change into editing state, click icon, you can delete your favorites.
Select one of the devices on “Live list” enters the video preview interface.

Button instruction：

1.3 device management

Click the button” device management” on the main menu and enter “device management” interface.

Icon instruction：

Modify the connection parameter

Click on the icon, select “modify connect parameter”, then into “modify device” dialog box：

A）Click on the icon, return to the device management lists.
B）Click on the icon, save the current configuration.

Modify the name

Click on the icon, select the option “modify the name”, then pops up “modify name” or “modify the catalogue” dialog box.

A）Click “OK” button to save the current configuration.
B）Click “cancel” button to cancel the modifying.
Delete

Click on icon, select “delete’ button to delete the current device directly
Add the catalogue

Click on icon, select “add the catalogue” option, then pops up “add the catalogue” dialog box

A）Click “OK” button, it will be saved the current configuration. Then will be showed in the device management list.
B）Click button “Cancel” to cancel to add the catalogue.
Add the device

Click on the icon to select “add the device” option.

Icon instruction

Add the shot

Please see the operation introduction of “add devices”.

Search the local device

Click on the icon to enter “search” dialog box. If there are some devices in local place, you would search out the corresponding device.

Icon instruction

Click on the icon, then pop up the menu as follows:

A）Add a device: add DVR (multi- channel)
B）Add a shot: add a single camera (single channel)
C）Modify the name: modify the name of the device or shot
D）Modify IP: Modify the IP address, subnet mask, gateway information
E）Modify the device password

1.4 Playback

Click button “playback” option in the main menu, and then select to playback the video.

After select an event type, start time and end time, clicking on the icon will list out the remote video lists, and then click on the item will be selected to play or download videos.

1.5 Alarm management

Click the option of “alarm management” in the main menu

Icon instruction：

Guard

Click on the icon to select “guard” option, pop up the dialog box as follows:

Select the option those need to alarm and click the button “setup” to save the current settings; Click the button “cancel” to cancel the current settings.

Unguard

Click on the icon to select the button “unguard”, cancel the current camera setting.

Note

Click on the icon to select “note” option, and then pop up the dialog as follows:

A）SMS notification: set the cell phone number of alarm notification
B）News push: open/ close the news push setting
In the notification interface, and then into “SMS notification” interface

Icon instruction

Record

Click on the icon to select “record” option, and then pop up the dialog of “alarm record”

The icons instruction

1.6 Local playback

Click on “local playback” option in the main menu, and then into the interface as follows

Click on the icon, the local playback video list change to editing states.

Select the video options that you want to delete, and then click the icon; you can delete the selected local video.

1.7 Image view

Click on “images browsing” option

Click on the icon, the local playback video list change to editing states.

Select the image options that you want to delete, and then click on the icon to delete the selected local images.

1.8 Modify password

Click on” modify password” option in the main menu, and then into the interface as follows:

Click on the icon to save the current modified password.

1.9 Local configuration

Click on “local configuration” option in the main menu, and then into the interface as follows

Function instruction：

Click on the icon to save the current configuration.

.

.

.

.

.

.

.

.

.

.

.

.

2、iphone

.

Open the software into the login interface, inputting the username and password and click button “login”, then it will be login the application.

Icon description：

Notice: Please click “LoginFree”, directly into the system, without verifying user name and password. And you can get help information without login.

.

2.1 User register

User register

Click the button “register” on the login menu, then will jump to the register interface.

Enter the register information, click “register” then will be registered.
Note: 1 please enter the valid E-mail address in order to retrieve your password when you lost it.

2 No account login version, no such function! 
retrieve the password

On the register clicking the button “login” and jump to “Retrieve password” interface.

Input the username, click button “retrieve password”.
If you have entered your name and email address when registering and the username has been occupied, then “retrieve password” information will be sent to the email address.
.

2.2 Real-time preview

In the main menu, clicking “real-time preview
Click “Favorites” button, go to “collection management” interface

Select one of the devices on “Live list” enters the video preview interface.

  

Button instruction：

2.3 device management

Click the button” device management” on the main menu and enter “device management” interface.

Icon instruction：

Modify the connection parameter

Click on the icon, select “modify connect parameter”, then into “modify device” dialog box：

A）Click on the icon, return to the device management lists.
B）Click on the icon, save the current configuration.
Modify the name

Click on the icon, select the option “modify the name”, then pops up “modify name” or “modify the catalogue” dialog box.

A）Click “OK” button to save the current configuration.
B）Click “cancel” button to cancel the modifying.

Delete

Click on icon, select “delete’ button to delete the current device directly

Add the catalogue

Click on icon, select “add the catalogue” option, then pops up “add the catalogue” dialog box

A）Click “OK” button, it will be saved the current configuration. Then will be showed in the device management list.
B）Click button “Cancel” to cancel to add the catalogue.

Add the device

Click on the icon to select “add the device” option.

Icon instruction

Add the shot

Please see the operation introduction of “add devices”.

Search the local device

Click on the icon to enter “Device search” dialog box. If there are some devices in local place, you would search out the corresponding device.

Icon instruction

Click on the icon, then pop up the menu as follows:

A）Add a device: add DVR (multi- channel)
B）Add a shot: add a single camera (single channel)
C）Modify the name: modify the name of the device or shot
D）Modify IP: Modify the IP address, subnet mask, gateway information
E）Modify the device password
.

2.4 Playback

Click button “playback” option in the main menu, and then select to playback the video.

After select an event type, start time and end time, click the button OK will list out the remote video lists, and then click on the item will be selected to play or download videos.

2.5 Alarm management

Click the option of “alarm management” in the main menu

Icon instruction：

Guard

Click on the icon to select “guard” option, pop up the dialog box as follows:

Select the option those need to alarm and click the button “OK” to save the current settings; Click the button “Cancel” to cancel the current settings.

Unguard

Click on the icon to select the button “unguard”, cancel the current camera setting.

Note

Click on the icon to select “note” option, and then pop up the dialog as follows:

A）SMS notification: set the cell phone number of alarm notification
B）Message push: open/ close the news push setting

In the notification interface, and then into “SMS notification” interface

Icon instruction

.

Record

Click on the icon to select “record” option, and then pop up the dialog of “alarm record”

The icons instruction

.

2.6 Local playback

Click on “local playback” option in the main menu, and then into the interface as follows

Click on the icon, the local playback video list change to editing states.

Select the video options that you want to delete, and then click the button “delete”; you can delete the selected local video.

2.7 Image view

Click on “images browsing” option

Click on the icon, the local playback video list change to editing states.

Select the image options that you want to delete, and then click on the button delete to delete the selected local images.

2.8 Modify password

Click on” modify password” option in the main menu, and then into the interface as follows:

Click on the icon to save the current modified password.

2.9 Local configuration

Click on “local configuration” option in the main menu, and then into the interface as follows

Function instruction：

Click on the icon to save the current configuration.

.

.

QmEye_PC_Client_

1、Install

Double-click to open QmEye installation file, pop up following the installation wizard(The version number may be different, but not influence use)

.

Click “next” until the following interface, click the “install”

.

After the installation of software, pop-up window as follows:

.

Click “finish”

.

.

.

.

2.1 Login

Start the application, the program into the landing interface, as shown in P2-1

.

P2-1 Login

  Enter account and password to log in. If the user does not have the account , you can apply for to register.  And local login is permitted.

2.2 Register

Clicks the “register” on the login interface, enter the registration screen, as shown in P2-2.

.

P2-2 Register

With * is required, fill in and then click the “register”.

2.3 Password lost

If users have account, but forget the login password.You can through the e-mail to retrieve password. Click “Password lost”, Enter the following interface

.

图2-3 Password lost

  Mail QueryL: Check the reserved E-mail information when registering.

  Retrieve Password: System will send an email to the email, according to the prompt to reset the login password

2.4 Main Interface

  After the success of the user login, enter the main interface, as shown in P2-4.

.

P2-4 main interface

  Main interface is divided into four parts, including at the top of the navigation bar(P2-5), he left menu bar – device list and function(P2-6), in the middle of the play rect(P2-7), And at the bottom of the play controls(P2-8)

.

P2-5 Navigation bar

.

P2-6 Device list and function

.

P2-7 The play rect

.

P2-8 Play controls

  The description of each icon function as the following:

2.5 Control panel

.

Picture 2-9 control panel

  .

Screen locking: Lock the screen, in the lock case is not able to do any operation in current interface apart from unlocking.(PS: It is not permitted, on local login mode.)

Log off: logout the client

Playback: to playback the remote video and local video

Photos: view local images save by capture

Password Correcting: modify the user logon password(PS: It is not permitted, on local login mode.)

Alarm Settings: set the front-end device booted and alarm monitoring types(PS: It is not permitted, on local login mode.)

Device Searching: search all device which in LAN

DeviceAdministration: for operation such as rename, add, delete a device.

2.6 Add the Device

2.6.1 Quick Add

     “Control Panel” ->” Device Searching”, then pop up the device searching interface, as shown in P2-10

.

P2-10 search the device

  .

     Select out a device is searched, and then click “add to the list” filling device login ID and password, as showed in P2-11

.

P2-11 add a device to lists

.

Parent directory: add the camera to specific catalogue

Scene name: add to the display name of the user to the device lists.

Username: login username of the device

Password: the login password of the device

Channel NO: view what channel number, start from 1. Completed IPC as 1

Streaming: request to a front- end device stream format while live preview, default is sub stream. Fulfill the above information: after finished, click “add” button

.

.

图2-12

2.6.2Add the device manually

  .

“Control the panel” ->”Device management”, then pop up the device management interface, as shown in figure 2-13

.

.

Picture 2-13 device management

Firstly, select a directory from the device list box, then click “add the cameras” enter the added interface like the following figure:

.

Picture 2-14 add cameras

  .

     Device name: the display name that you add to the user device list, more convenient to people identify (such as living room)

    Device type: lens (the channel of the IPC, DVR\NVR), device (such as DVR\NVR)

    Connection modes: (IP address and port access mode), P2P (cloud- penetration mode)

    Protocol: select the front-end device protocol

Cloud ID: front-end device ID to identify the device, P2P mode exclusive.

Username: the login username of device

Password: device login password

    Channel NO: view what channel number, start from 1. Completed IPC as 1 (if it is the device type, it is the channel number mean: complete 8 if is 8Channel DVR)

    Stream: request to a front- end device stream format while live preview, 0 is main stream,1 is sub stream, default is sub stream.

.

2.7 Alarm setting

“Control the panel” ->”alarm configuration”, then pop up the alarm setting interface, as shown in figure 2-15

.

.

Picture 2-15 alarm setting

     Guard: start 4 alarm types monitoring which you tick

      Unguard: cancel all alarm types monitoring

PC Push: after booting and the related equipment alarm is triggered, the server will push the information to the PC client and prompt the user

Add number: add SMS notice number

Delete number: delete SMS notice number

Turn off the alarm: turn off the alarm, which the PC client is no longer to prompt the push information of device trigger alarm

Open the alarm: turn on the alarm, which the Pc client will prompt the push information of device trigger alarm.

View the alarm information: after starting current PC to view all alarms push messages.

    .

2.8Video playback

2.8.1 Remote video playback

  .

“Control the panel” ->”video playback”, then pop up the video select operation interface, (as shown in figure 2-16), select “remote video” then into remote video playback interface, as shoun in figure 2-17

.

.

Picture 2-16 video types select

.

.

Picture 2-17 remote video playback

      Select a device and set up the query time then click it to acquire the relevant video information. as shown in figure 2-18

.

Picture 2-18 remote video lists

.

  Double click a video to play in the video lists (as follows), double click the playing interface can be full screen.

.

Picture 2-19 remote video playback

2.8.2 Local video

“Control the panel” ->”video playback” -> “local video”, then pop up the local video interface, (as following:

.

.

    Select the local video date that need to view. Query the related video and double click to play.

.

IP Camera

IE Browser User Manual

Preface

Thank you for using our IP camera products. This series of products are all-in-one IP cameras designed for network video surveillance, including box IP camera, infrared box IP camera, dome IP camera, speed dome IP camera, etc. The products adopt high performance and powerful single SOC chip media processor to integrate audio and video capture, compression and transmission. Standard H.264 Baseline and Main Profile coding algorithm ensures clearer and smoother video transmission effect. Built-in Web Server allows users to easily perform real-time monitoring and remote control over front-end cameras via IE browser.

This series of IP cameras is suitable for small and medium-sized enterprises, families, and other environments that require remote network video transmission and monitoring. It is easy to install and operate.

.

.

.

Statement:

.

.

.

.

Readership:

  This manual is suitable for engineers as follow:

.

Notes:

Herospeed Firmware Software Download

.

NVR

The Network Video Recoder support network video access,and it has adopted a number of advanced IT technologies,such as audio/video codec technology(h.264,h.265,h.264+,h.265+),embedded system technology,storage technology, network technology and intelligent technologies.It can work independently as NVR,or as a powerful security networking system.

.

.

NOVATEK IP Camera

The NT IP Camera has adopted embedded system and a number of advanced IT technologies,such as audio/video codec technology(h.264,h.265,h.264+,h.265+),and integrated code compression, two-way audio intercom.

NOVATEK IP Camera

.

Rockchip IP Camera

The RK IP Camera has adopted embedded system and a number of advanced IT technologies,such as audio/video codec technology(h.264,h.265,h.264+,h.265+),and integrated code compression, two-way audio intercom, intelligent analysis , PTZ,HDR, lens control, alarm input and output, buffer storage and network transmission and other functions.

.

Rockchip IP Camera

Fullhan IP Camera

The Fullhan High-definition network camera has adopted embedded system and a number of advanced IT technologies,which integrated code compression, two-way audio intercom, intelligent analysis , PTZ, lens control, alarm input and output, buffer storage and network transmission and other functions.

.

Fullhan IP Camera

.

GK IP Camera

GK IP Camera uses an embedded system and a number of advanced IT technologies, such as audio and video encoding and decoding technologies (h.264, h.265, h.265+, H264+), integrated encoding and compression, supporting audio noise reduction, and response cancellation, Support humanoid detection, support full Netcom function, can realize plug-and-play access to the back-end.

.

GK IP Camera

.

XVR

The Embedded Hybrid Digital Video Recorder is compatible with HDTVI,AHD and other coaxial HD specification,which can be accessed to any HDTVI,CVI,AHD,analog and network signal.It can disable numbers of analog channels and convert them to IP channels,which have both functions of DVR and NVR.

.

XVR