The VDG Sense app features:
– Add servers: add multiple VDG Sense servers to your app, making it incredibly easy to switch between servers and different sites.

– Select cameras: select your camera by swiping horizontally and vertically through camera locations. Recognize the video channel by thumbnail and camera name.

– View: view images full screen with one-tap zooming. Zoom in on any object by simply tapping the live video. View the next or previous camera by swiping horizontally.

– Control: control any PTZ enabled camera in VDG Sense directly, using the joystick control for pan/tilt and zooming in landscape position. Quick selection of the first six pre-sets available on your camera.

– Store: save any incident directly to your photo library by tapping on the image icon. Share the images by using your choice of any other app, such as your e-mail app or messaging app.

Chapter 1 – Introduction

This manual explains all necessary steps to create a fully functional Sense installation in a relatively short time. It assumes a simple standalone or single-server, single-client setup where all components are configured and accessible via the network:

Sense Server-Client installation:

Chapter 2 – Installation

To install VDG sense the VDGSenseSetup.exe is required. It can be downloaded in the support section here: https://support.tkhsecurity.com/downloads/software/ website. It is a single executable installer which include all required components to install VDG Sense as server, client or standalone system. The diagram below shows the components of VDG Sense Setup.

2.1 Versioning

After starting the VDG Sense Setup the first page the version details page. It shows version information of all included and already installed Sense components.

2.2 Standalone installation

To install VDG Sense as standalone system check both ’Client’ and ’Server’ boxes. It will install the following Sense components:

2.3 Client installation

To install the VDG Sense client, only select the ’Client’ checkbox. It will install the following Sense components:

2.4 Update

The installation package VDG Sense Setup is also used to update VDG Sense to a newer (or lower) version. Use the same procedure as described in paragraph 2.2 and 2.3. IMPORTANT: an update will not remove the license or settings.

Note: Upgrading older VDG Sense versions to the latest VDG Sense version requires special attention to our upgrade instructions which can be found in our knowledgebase:

*Upgrading/Downgrading VDG Sense

Chapter 3 – Starting VDG Sense client

3.1 Signing in

Installing VDG Sense as client or standalone system will put a desktop icon with the name ‘Sense Client’. By double-clicking on ‘Sense Client’ the application will start and show the login dialog, see below.

It contains the following items:

3.2 Menu

After signin the main application starts by showing the top menu bar. If a user with administrator rights signs-in, no layout will be shown. If a normal user signs-in either the first layout in the layoutlist is shown or the multi-layout which is configured as default.

From left to right the top menubar functions are:

Chapter 4 – License

Sense is protected by a software license key. In order to use the product a software license file is required. A Sense license only needs to be applied to the ‘Sense Video Manager’. As ‘Sense Video Manager’ does not have a graphical user interface the license needs to be uploaded and activated using the ‘Sense Client’. The license key can either reside on the license USB stick or provided by e-mail.

4.1 Upload license

Activation is the process by which the software and license key are validated to ensure that they are used in accordance with the purchased license and services. Activation is intended to protect your end user rights as well as TKH Security’s rights as a software author. Only genuine Sense software entitles you to critical updates and technical support. You may not be able to use Sense software if it is not activated.

Requirements

4.2 Activate license

4.2.1 Online activation

4.2.2 Offline activation

Save license file

Chapter 5 – Configuration

Sense settings are visible after clicking the toolset icon in the topbar menu. Settings are grouped in tabs where each tab holds specific settings related to the name of the tab. Normal procedure to setup a Sense system is to work through the setup tabs from left to right, starting with the server tab and ending with user management. Configuration is normally done using the administrator account.

5.1 Servers

The server tab holds the list of servers and settings related to the selected server. From left to right you see the serverlist, the cameralist of the selected server, settings of the selected server and server statistics related to CPU, memory, network and harddisk load.

 5.1.1 Add via find

Click ’Find’ in the lower left corner of the screen to open the find dialog. After a few seconds it shows the list of all servers found in the local network on all NIC’s. Select the server(s) and click ’Add’ to add selected server(s) to the configuration and close the dialog.

5.1.2 Add manually

To add a server press ’+’ in the lower left corner of the screen. Enter the server address in the dialog which appears. On a standalone system the localhost server (127.0.0.1) is automatically added to the list. In a server-client configuration the server is also automatically added to the list after login.

5.2 Devices

A list of Sense-compatible devices can be found here: https://support.tkhsecurity.com/compatibility-list/camera/

The ’Devices’ tab contains the list and configuration of devices for the selected server. The server can be selected just below the ’Server’ tab.

The devicelist has three sections which are from left to right:

5.2.1 Add via find

Click ’Find’ in the lower left corner of the screen to open the find dialog. After a few seconds it shows the list of all devices found in the local network on all NIC’s, including intercom servers and IO devices. Select one or more cameras and click ’Add’ to add selected devices to the configuration. It will also close the dialog.

5.2.2 Add manually

Click ’+’ in the lower left corner of the screen to add a new device to the list.

Fill in all required fields to connect to the device. See the list below for explanation on the fields.

5.3 Layouts

The ’Layouts’ tab is used to configure all (multi)layouts. Layouts are required in operator mode to display live or recorded video or to handle (video)events. They can be custom designed to fit the needs of the operator.  The layout manager is a floating menu which is used to create, delete and modify (multi)layouts and panels.

A layout consists of panels where each panel has a specific function. For instance a panel can be used to display live video, recorded video, for playback controls, display a map or to manage events. The complete list of panel types can be found in the ’Type’ list in the panel section of the ’Layout Manager’.

5.3.1 Live layout

Click ’New’ in the ’Layouts’ menu of the ’Layout Manager’ to create a new layout. The following dialog will appear:

This dialog provides three ways of creating new layouts:

The icon in the lower left corner of each panel identifies the type of panel. A panel for live video uses a camera icon as identifier. After selecting a panel its properties are shown in ’Panels’ section of the Layout manager. To assign a deviceto the selected panel select the camera in the ’Device’ list of the panel properties.

5.3.2 Playback layout

Click ’New’ in the ’Layouts’ menu of the ’Layout Manager’ to create a new layout. The following dialog will appear:

This dialog provides three ways of creating new layouts:

This layout is composed of 4 playback-panels in the upper half of the layout and controls to actually playback recorded video in the lower half of the layout. The panel to display recorded video uses a triangle icon as identifier. To assign a camera to the selected panel select the camera in the ’Devices’ list of the panel properties.

5.3.3 Multi layout

A ’Multi Layout’ is a group of layouts with a pre-defined monitor selection. It is used to quickly assign several layouts at once to different monitors. They are also used to define the default layouts to be displayed based on which user logs in. User Management is explained in the next paragraph. To create a multi-layout click ’Edit’ in the ’Multi-Layout’ menu of the layout manager, a dialog will appear:

On the left side of the dialog is the list of multi layouts. Multi layouts can be added, removed or edited by using the buttons below the list of ’Multi layouts’. On the right side of the dialog is the list of monitors which belong to the selected multi layout. Monitors can be added or removed using the buttons below the ’Layouts’ list. The monitor numbering corresponds to the monitor numbering in the ’Monitors’ tab and in the top menu bar. To assign a layout to a monitor, select one from the list of layouts next to the monitor icon.

NOTE: a layout only can be assigned once per multi layout. When finished click ’Close’ to close the dialog.

5.4 User Management

Sense User Management provides the administrator with the ability to control the access level of users logged in to Sense. Access to cameras, servers, layouts and several other functions can be limited to groups of users. In Sense this is called a ’User Group’, it holds the privileges of users assigned to the group.

5.4.1 Users & Groups

The Users & Groups is used to manage all user related settings in Sense. On the left side of the screen is the list of user groups. User groups can be added, removed or modified using the buttons below this list user groups. On the right side of the screen are the privileges which can be assigned to the groups, divided by subtabs.

Click the ’+’ button at the bottom below the group list to add a user group, a dialog will appear where the name of the user group can be entered. Click ’Ok’ in the dialog to create the group and close the dialog.

Create User:

Click ’+’ below the ’Users’ list in the users subtab to create a user. A dialog appears where the name, username and password of the user can be entered.

Create Devicegroups:

A devicegroup can be used to define which cameras a user is allowed to see. Open tab ’Device groups’ to create a device group. On the left side is the list of created device groups. Using the buttons below the list devicegroups can be added, removed or edited. On the right side is the list of cameras.

Click ’+’ below the ’Device group’ list to create a devicegroup. A dialog appears where the name of the device group can be entered. Use a meaningful name, like ’All cameras’. Click ’Ok’ to close the dialog and add the device group to the list. Drag and drop the cameras from the cameralist on the right to one of the device groups on the left.

Assigning privileges:

If all users, layouts, multilayouts, servers and devicegroups are created, they can be drag and dropped to the corresponding usergroup. To remove a privileges select the it in the usergroup and Click ’-’ below the grouplist or press the ‘Delete’ button on your keyboard.

As an example, the steps to create a usergroup called Operators should look like this:

5.4.2 Configure Autologin

Sense Client can be configured to launch automatically on Windows startup after windows login and to automatically sign in to a Sense Server. Click on the gear wheel in the lower left corner of the dialog to open the settings.

On the left side of the screen the default server, username and password can be entered. On the right side the program language, videowall mode and the automatic startup/sign-in option can be selected. In normal operation the videowall mode does not need to be selected and is beyond the scope of this guide.

Chapter 6 – Operation

Click following link to see the video manual: https://support.tkhsecurity.com/downloads/manuals/

Live mode or ’Home’ is accessed by clicking on the ’Eye’ icon on the upper left corner of the screen of the first monitor. This icon is also used to open the menu where Layouts can be selected. See below for a screenshot of a multi-monitor setup. The left monitor shows a layout with live cameras and the right monitor shows a layout for playback. These are the layouts which are created in ’Setup’ mode.

6.1 Live Menu

The Live menu is accessed by clicking on the ’Eye’ icon on the upper left corner of the screen of the first monitor.

It contains the following items:

Multi Layouts: Contains all multi-layouts available for the currently logged in user. Selecting a multilayout will update all monitors which are configured in this multi-layout.

Layouts: Contains all layouts available for the currently logged in user. Selecting a layout will update the currently selected monitor with this layout.

Cameras: Contains all cameras available for the currently logged in user sub-grouped by location names. The subgroup ’All locations’ contains all cameras. Selecting a camera will update the currently selected videopanel in the layout.

Camera Sequences: Contains camera sequences for the currently logged in user.

.

6.2 Tools Menu

The tools menu is accessed by clicking on the ’Toolbox’ icon on the upper left corner of the screen of the first monitor.

It contains the following items:

Search, provides functions to search for events and meta data.

Face Match, eventlist for use with FaceR algorithms.

Database, maintains person list for use with CarR and FaceR algorithms. FaceR and CarR are available if included in the license.

System Alerts: Opens the System Alerts dialog

Video Tags: Opens the Video Tag dialog

6.3 Live

This layout contains 4 live panels where each panel has the following features:

6.3.1 PTZ controls

The live control panel is needed to control PTZ domes. This panel can be pre-configured in a layout, but it will also automatically appear after double-clicking on a videopanel with a PTZ device; the camera will be displayed in fullscreen mode including the dome controls. PTZ commands are sent to the camera which is currently selected (which has a green border).

To pan and tilt a ptz camera hold the left mouse button and move the cursor over the orange dial. The speed of the dome is determined by the cursor-distance from the center of the dial; close to the center the speed is low, on the outside the speed is high. The buttons have the following functions:

	Focus near.
	Focus far.
	Switch auto focus/auto iris on.
	Zoom in.
	Zoom out.
	Open iris.
	Close iris.
	Go to preset ‘Home’.
	Go to preset 1.
	Rotate 180 degrees.
	Save the current position of the dome as a preset.
	Go to the selected preset in the list.
	Opens the preset dialog to give each preset a name.

6.4 Playback

Below is an example of a playback layout that has been created for an operator.

This layout contains 4 playback panels and playback controls where each panel has the following features:

6.4.1 Playback control options

For creating a playback layout, it is needed to create a layout that contains one or multiple panels of the type ‘Playback’ and a control panel to start/stop the playback. There are two types of playback controls available. By default when creating a playback layout or when switching to fullscreen playback, the timeline panel is used.

Option 1: Timeline panel (Preferred)

The red line indicates what the current time/date is of the playbacked recording and thumbnails of the recordings are visible. Also motion detection (if enabled for this camera) is shown in yellow.

	Playback backwards. For streaming codec video only I-Frames are played back.
	Stop playback.
	Playback forward.
	Opens the export image dialog, explained in section 6.3.3 on exporting images.
	Quick option to go to a specific date
	Motion detection
	Option to visualize motion detection, vca events or audio on the timeline panel

Option 2: Alternatively, there is the playback controls panel as a legacy option with the more classic control buttons and slider.

The Playback controls panel is needed to playback recorded video. It has two trackbars where the top bar has a resolution in days and the lower trackbar has a resolution of 24 hours (of the selected day). The playback speed is set by the ’red-green’ trackbar; red is backwards, green is forwards. The date and time on the left and right side of the trackbars correspond to the first and last recorded video image of the cameras which are visible in the layout. From left to right the function of the buttons are as follows:

	Go to the beginning of the recordings of the cameras visible in the layout.
	One minute backwards
	One frame backwards.
	Playback backwards. For streaming codec video only I-Frames are played back.
	Stop playback.
	Playback forward.
	One frame forwards.
	One minute forwards.
	Go to the end of the recordings of the cameras visible in the layout.
	Opens the date time search panel.
	Set export range, explained in section 6.3.2 on exporting video.
	Enable audio playback and set playback speed to realtime (panel should be selected to hear the audio).
	Opens the export image dialog, explained in section 6.3.3 on exporting images.
	Opens the export video dialog, explained in section 6.3.2 on exporting images.

6.4.2 Export Video

Recorded video (and audio) can be exported to different media: CD/DVD, hard drive, USB stick or network share. A single export can hold video of multiple devices from multiple servers in the same time range. The video itself is exported in Sense format, it is not transcoded to a generic codec. The export comes with a program called ’Sense Player’ which is used to playback exported video. To open the ’Export Video’ dialog press the export video button in ’Playback Controls’.

Other options are using the playback controls trackbar or using the start/endtime edit box in the video export dialog:

Timerange using trackbar:
Click ’E’ in the playback controls panel, three buttons appear: ’Start’, ’Clear’ and ’Stop’. Set the thumb-tracker to the starting point of the video that needs to be exported and click ’Start’. Set the thumb tracker to the end point of the video that needs to be exported and press ’Stop’. The time range is highlighted in green. To clear the selection and start over click ’Clear’. After defining the range open the video export dialog. The camera(panel) which has focus will automatically be added to the list of export cameras. The begin and end time are also set automatically.

Timerange using dialog:
Video can also be exported manually without using the trackbar to define the time range. When opening the export video dialog it will use the current playback time (position of thumbtracker) and set the start time with current time minus 5 minutes and end time to current time plus 5 minutes. The camera(panel) which has focus will automatically be added to the list of export cameras.

6.4.3 Export Image

Single images or snapshots can be exported from recorded video to a PDF document which can be stored to any windows storage location (like a USB stick). The PDF report contains information about the exported image and comments which can be entered in the Export Image dialog. To create a report select the playback panel with the image that should be exported and click the ’Disk’ button in the ’Playback Controls’ (see section 6.3.1 on playback controls), it will open the dialog as shown below:

General Questions about Kasa Cam Outdoor

For all Kasa Cam’s basic information, please click here for details.

Below are some general questions about Kasa Cam Outdoor only.

Q1: How should I clean the surface of the Kasa Cam Outdoor?

You can clean dirt off your Kasa Cam Outdoor using a damp washcloth and wiping the edges off. We recommend caution when wiping the face of the camera so that you do not scratch the lens.

Q2: Do I need a hub for the Kasa Cam Outdoor?

Some Kasa Cam Outdoors are hub free and designed to work straight out of the box with your existing wireless network. All you need to get started is a safe and covered outlet for you to plug the camera AC adapter into, for example, KC200.

While some must work with a Kasa Hub and users will need to add the Hub first on Kasa APP, for example, KC300.

Q3: How far can I place the Kasa Cam Outdoor from my Wi-Fi router?

The average range of Kasa Cam Outdoor cameras can be 25-50 feet away from the router. This range varies based on your router model, home type and wireless interference. You can test your camera’s signal strength from the device settings menu from within the app.

Q4: Is Kasa Cam Outdoor battery powered?

Only KC300S2 and KC310S2 support battery-powered, the other Kasa Cam Outdoor can only be powered by being plugged into an electrical outlet.

Q5: Is KC200 completely wire free?

The kasa cameras are not completely wire free, as long as you need to power them on with the provided power cord.

However, kasa cameras are wirelessly connected to your Wi-Fi network after successfully setting them up.

Q6: Is there an extension cable for KC200?

We do have the extension cable for KC200, and its model is KA200E. Please click here for more details.

Q7: How do I turn my Kasa Cam Outdoor Siren on/off?

From the live view screen, tap the siren icon to be taken to the siren on/off button. Tap once to trigger the siren, tap again to disarm it.

Q8: What can I do if bugs are triggering my Kasa Cam Outdoor?

If your Kasa Cam Outdoor is placed in an area where dust or bugs are a problem, you can change the minimum motion duration setting. You can configure the minimum motion duration found in the Privacy and Sensitivity tab of your camera setting. Refer to the question “How can I reduce the number of false alerts I receive from my Kasa Cam Outdoor?”

Questions Regarding Kasa Care Subscriptions

Q1:  Do I have to purchase Kasa Care individually for each of my cameras?

Kasa Care services have Plus and Premium plans.

If you subscribe to the Plus plan, you need to subscribe to the Kasa Care service for each camera individually.

The Premium plan applies to per Kasa account. After you subscribe to the Premium plan, up to 10 cameras bound to the Kasa account can enjoy the Premium plan.

Please see FAQ-1962 for details on plans and pricing.

Q2:  When will my Kasa Care subscription start and when will I be billed?

Your Kasa Care subscription starts on the day after your set up the camera successfully. You can select to use the free plan or purchase a monthly/yearly subscription. You will be billed on the same day when your monthly/yearly subscription is activated.

Subscriptions automatically renew, and users can cancel the plan before the next bill date to avoid being billed for the next cycle.

Note: With a free plan you’ll only have access to your last 12 hours or 2 days of video history depending on the Kasa Cam’s model number. You may opt-out by Canceling the paid plan before your trial ends.

Q3:  How do I change my Kasa Care payment information?

You will be able to change your payment information at any time through the Kasa app. Launch the Kasa app, click on the “ME” icon at the lower right corner of your screen, go to Kasa Care, and then click on Payment to change your payment information.

Kasa Care only allows for one payment card on file at a time.  Notifications of transactions, subscription and payment issues will be sent via email.

Q4:  Can I change my billing cycle?

Yes, you change your billing cycle for each Kasa account. When changing from an annual to a monthly plan we will refund you for the remaining unused days of Kasa Care.

You can change your billing cycle by selecting Kasa Care from the side bar, canceling your current subscription and creating a new subscription.

Q5:  How do Kasa Care subscription renewals work?

Your Kasa Care subscriptions will automatically renew at the end of the billing cycle unless you choose to cancel the service.

General Questions about Kasa Care

We released the new Kasa Care service in 2020. For detailed information about the new Kasa Care service, please refer to What is Kasa Care.

Here is what you might want to know about the new Kasa Care service.

Information related to the free trial

Q1: Is there a free trial for the Kasa Care plan?

With the new Kasa Care service, every Kasa account is eligible to sign up for a free trial for the new Kasa Care plan once.

To view the Kasa Care plan, From the Kasa APP > Tap’Me’ on the bottom> Select Kasa Care

Q2: Can I get a free trial for the new Kasa Care if I already had a free trial of the legacy Kasa Care plan?

Yes! Every Kasa account is eligible for a one-time free trial of the new Kasa Care services.

Q3: How many free trials can I have for the Kasa Care plan?

Each Kasa account is eligible to sign up for a free trial once.

Q4: Can I cancel a free trial?

Yes. You can cancel a free trial at any time from the Kasa app. Do note, however, that your account will not be eligible for another free trial after the cancellation.

Information related to User Migration

Q5: How to migrate from the legacy Kasa Care plans to the new Kasa Care plans

If you have active legacy Kasa Care subscriptions for your Kasa Cameras, you can migrate to the new Kasa Care plan on your Kasa app. To view your options, open the sidebar by tapping the “≡” button in the upper left corner of the Kasa app and select Kasa Care.

To migrate and upgrade, please click on “Upgrade to New Plans” and you will be taken to the new Kasa Care ‘Select Services’ screen. You could just follow the subscription instructions to finish the migration. All legacy Kasa Care subscriptions will be terminated, and the prorated refund will be issued to your credit or debit card on file.

You can also cancel your existing subscription first and subscribe to a new Kasa Care plan later. Upon cancellation, all legacy Kasa Care subscriptions will be terminated, and the prorated refund will be issued to your credit or debit card on file.

Please note that once you’ve completed all the steps of “Upgrade to New Plans” or “Cancel Subscription,” you cannot purchase the legacy Kasa Care plans again.

Migration is one way and cannot be undone.

Please contact TP-Link support if you see a message reporting that “This subscription cannot be refunded” while migrating to the new Kasa Care plan.

Q6: Do I still have access to the legacy Kasa Care’s free features after I cancel my legacy service?

First, you will be refunded when you cancel the legacy Kasa Care Plans. After cancellation, your Kasa Cameras will automatically revert to the legacy Kasa Care’s free features:

· KC100 and KC110 will still have 12 hours of free cloud storage for 2 years from the original setup date.

· KC120 and KC200 will still have 48 hours of free cloud storage for 2 years from the original setup date.

· KC300 will still have 48 hours of free cloud storage for 1 year from the original setup date.

· KC310 will still have 12 hours of free cloud storage for 1 year from the original setup date.

Depending on the camera, you will have one or two years of free cloud storage.

Any paid subscriptions will not pause the countdown clock on your free storage.

Please note that once you’ve canceled a legacy Kasa Care plan or migrated to a new Kasa Care plan, you cannot subscribe to the legacy Kasa Care plans again.

Q7: Can I keep my existing legacy Kasa Care plan for my Kasa Camera?

Yes. You can keep your existing legacy Kasa Care plan. However, if you cancel or make changes to your plan, you will not be able to return to the legacy plan. You can switch to a new Kasa Care plan anytime from the Kasa app.

Q8: Can I alter my legacy Kasa Care plan?

You cannot make other changes to your legacy Kasa Care subscriptions.

You can cancel your legacy Kasa Care plan or migrate to a new Kasa Care plan at any time.

Plan cancellation and change

Q9: Can I cancel or change my Kasa Care subscription?

Yes. Your Kasa Care plan cancellation/change will take effect immediately. All video history outside of the new plan limits will be erased and cannot be recovered.

Either a prorated refund or a prorated credit will be issued accordingly.

If you still have one or more cameras in your Kasa Care subscription, you’ll get a prorated credit applied to your next bill.

Note: Your Kasa Care subscription can either be billed monthly or annually. You can found the current billing cycle (next invoice date) by tapping on the Kasa Care in the sidebar of the Kasa app.

If you wish to change your billing cycle, you may tap on the Kasa Care in the sidebar, canceling the current subscription and create a new one.

Refund Policy Summary Table

Other Questions

Q10: Can I add more than 10 cameras to one premium plan subscription?

No. The maximum number of cameras under one Premium Plan subscription is 10. If you want to enable Kasa Care service for more than 10 cameras, you can sign up for another Kasa account or change all cameras to Plus Plan. Plus Plan subscriptions are per camera and there is no maximum camera limit.

Q11: Can I subscribe to both Plus and Premium Plans at the same time for one Kasa account?

No. Only one subscription type is allowed per Kasa account.

Q12: Does my Kasa camera still have a free cloud recording?

When you register for a Kasa Cam, you can enjoy the free Kasa Care service depending on the model number of the camera.

With the free service, you will have access to 12 hours or 2 days of video history for the Kasa cameras.

Note： The other cameras don’t have free cloud recording except the models listed below.

Note: The 2-year/1-year free plan begins after the camera is set up successfully.

Q13: Does my Kasa camera still have a free plan if I cancel my subscription plans?

Yes! You always have the Free Plan for the Kasa camera. When you cancel the paid plan, the camera will go back to the free plan with 12 hours or 2 days of video history. Please note the free plan starts timing after the camera is set up successfully. The free plan will be unavailable only when it expires.

Q14: Can I Retrieve a clip that shows “No longer available”?

No, there is no way to retrieve these clips. Some users may want to see clips labeled “no longer available” in the Kasa app. These clips are not available since they are not stored on our server anymore.

You cannot retrieve these clips by subscribing to a Kasa Care plan, either.

Q15: Why can’t I use the manual recording feature on KC105 or KC115?

If you cannot see the manual recoding button on the live view page of the camera, it is likely that you have not subscribed to the Kasa Care Plan, thus there is no free cloud recording for the KC105 or KC115.

After the subscription, you will see the recording button and use the manual recording feature, the clip recorded will be saved to the activity center.

Q16: What’s the difference between a free plan and a free trial?

The free plan refers to 2-day or 12-hour Free cloud storage accompanied by the camera itself (depending on the model no. of the camera), which you can enjoy without subscribing to Kasa Care. The old models of Kasa Cameras, including KC100, KC110, KC120, KC200, KC300, and KC310 have this feature, while the new models that support SD cards do not have the free plan (free cloud storage).

Free Trial is a trial for a limited period when users subscribe to a paid Kasa Care.

The current offer is a 30-day free trial. This probation period may be changed at any time. We have not guaranteed the length of a free trial.

Q17: What types of cards are supported for payment?

We currently support Visa, Maestro, Mastercard and American Express for payment.

All four brands are supported for payment, including credit and debit cards for these brands.

Cancel or Downgrade Kasa Care service on Web Portal

If you made the subscriptions from the Kasa Care Web portal or in the old Kasa app (versions before Dec 2022), you can downgrade or cancel the service on Web portal , this article will introduce some points for attention.

If you made the subscriptions in the Kasa APP app (after Dec 2022 app update) please refer to this FAQKasa Care Cancellation and Refund

Q1: If I cancel Kasa Care, will it terminate immediately?

A: Yes, when you choose to cancel the subscription, the Kasa Care plan and service will stop immediately.

Q2: Can I receive refund after cancelling?

A: After cancelling the service, you’ll be issued either a prorated refund or a prorated credit. If you’ve cancelled your Kasa Care subscription, you’ll get a prorated refund. If you still have one or more cameras in your Kasa Care subscription, you’ll get a prorated credit applied to your next bill.

Q3: Can I view cloud video clips after cancelling?

A: No, all video history outside of the new plan limits will be erased and cannot be recovered. But you can also watch the clips which are no more than 30 days.

Q4: How can I cancel the Kasa Care service?

A: Log in to the Kasa Care official website https://kasa.tplinkra.com/ , and then choose the Kasa Care subscription and Tap on Cancel Subscription, reconfirm if you want to unsubscribe, and click REMOVE, the service will be cancelled immediately.

Q5: Could I downgrade my previous plan?

A: Yes, log in to the Kasa Care official website, and then subscribe to the new service you want to downgrade, then you will switch to the new service.

The Refund Policy Summary Table from website as below:

.

How can I buy a Kasa Care subscription for my camera

You can subscribe to the Kasa Care plan from the Kasa app or from the Kasa Care web portal.

This FAQ will guide you step-by-step to make a new subscription.

From the Kasa App (IOS)

1. To subscribe to a new Kasa Care plan, open Kasa APP, and access Me-> Kasa Care.

2. Click “Add Plan” to add the new Kasa Care service.

3. Choose the service you want to buy and click Subscribe.

4. Pay for it from APP Store.

5. Select the camera you want to add to the plan, the camera selected will be applied Kasa Care features after the subscription. If you do not see your camera in the list, please make sure it has the latest firmware and have internet access.

From the Kasa Care Web Portal or Andriod

1. If you use web portal, login the Kasa Care website(https://kasa.tplinkra.com) with your TP-Link ID;

If you use Android APP, open your Kasa APP and access Me->Kasa Care.

2. Click Add Service and choose the Kasa Care plan you want to use.

3.Select the cameras you want to add in the plan.

4.Choose the Billing Cycle you prefer, yearly or monthly.

5. Add your credit card info and pay for it.

If you need any help with Kasa Care, contact TP-Link technical support .Please try to provide the following information for us to better help with your case:

1.Your TP-Link ID

2.A screenshot of Error or a screenshot of Kasa Care payment record with Order ID.

If you need further assistance contact TP-Link Customer Support here.

What are activity notifications?

Kasa Cam utilizes your smartphone’s push notification feature to alert you of activity. When your camera detects any activity (sound and/or motion based on your camera settings), it will send a push notification to your mobile device. Tapping on the notification will take you to “Activity” tab in your Kasa app. From there you can view a video recording of the activity.

Step 1: Example of push notification

How do I turn on or off activity notifications on my mobile device?

Kasa Cam utilizes the push notification of your smart phone to inform you of detected activities by the camera. This feature can be turned on during or after the installation process. This guide will show you both.

During installation:

While going through the setup process, the app will remind you to enable the notification feature. If you tap “I don’t want to be notified, then you may need to turn on this feature manually after the installation process.

After installation:

Method 1:

1: Open your Kasa app, tap the “three lines icon” on the top left corner, and then click on “Settings”.

2: Tap “Notifications”, click on the camera which you want to enable notification function. Here we take KC120 as an example.

3: Enable “Activity Notifications”, if you select “Always” in the page, you will receive notifications all the time. If you select “Custom Time”, you can custom a time period when you will receive the notifications.

Note: If your enable “Automatically Limit Notifications”, Kasa app will limit the frequency of notifications you receive to no more than one notification per five minutes regardless of activity.

Method 2:

Here we take KC120 as an example.

1. Click on KC120, then click on the “three lines icon” on the top right corner, go to the Device Settings page.

2. Click on “Notifications”.

3. Enable “Activity Notifications”, and then select “Always” or “Custom Time” as your desire.

.

What is Kasa Care?

.

Kasa Care is a cloud-based service that allows users to view and download activity recordings from a Kasa Cam.

When you purchase a Kasa Cam, you can subscribe to our advanced plan to enjoy our Kasa Care cloud service.

Your Camera’s activity recordings are stored on the cloud and associated with your Kasa account. You can review, download, and share these recordings within certain days in the activity center on your Kasa app.

You could choose either Plus Plan or Premium Plan for your account.

The subscription is associated with the account, you can add cameras to the plan or remove cameras from it on Kasa APP.

* 30 days of video history – With 30 days of video history, you can see every event captured by your camera through a clip. The video history includes an activity recording clip, a snapshot of the detected activity, and the time the activity was recorded over the past 30 days

* Video sharing – Just tap the share button and you can quickly post your Kasa Cam clip to your preferred social media platform or share it directly with your friends and family. You can also download Kasa Cam clips to your mobile phone or tablet to keep them for long-stem storage.

* Rich notifications – When your Kasa Cam detects motion or sound, you’ll be alerted with a push notification featuring a snapshot of the detected activity, letting you decide at-a-glance if you need to respond now or later.

* Up to 10 Cameras – Kasa Care Premium represents fantastic value for multi-camera households, giving you access to all paid Kasa Care features for up to 10 cameras; it’s the way to go if you have four or more cameras.

Free cloud recording offering:

When you set up a Kasa Cam, you can enjoy the free Kasa Care service depending on the model number of the camera. With the free service, you will have access to 12 hours or 2 days of video history for the Kasa cameras

To access video history for more than 12 hours or 2 days, you have to upgrade to one of our paid subscription plans.

* Kasa Cameras that support SD card does not have this feature, you need to upgrade to one of our paid subscription plans to use the cloud storage and the features such as “Manual Recording”, “Activity Notifications with Snapshots”

Note: The 2-year/1-year free plan starts timing after the camera is set up successfully.

Do I have to create a Kasa account to be able to use the camera?

*Note: All Kasa Cams require and only work with the Kasa for Mobile App

Yes, if this is your first Kasa device, you will be asked to create an account when you add your first camera.  A Kasa account will allow you to manage the Kasa Cam and other Kasa devices.  After you create your account you’ll be sent a verification email to complete the registration process.

Step 1:  Tap Create Account

Step 2:  Type in your Email address and set a password

Step 3:  Confirm the email address and tap Continue

Does Kasa Cam have Night Vision?

*Note: All Kasa Cams require and only work with the Kasa for Mobile App

Yes, Kasa Cam comes equipped with Night Vision. Kasa Cam’s Night Vision will allow you to see what’s happening up to 30 feet in darkness. There might be slight difference in the distance of Night Vision, please click here for more details.

You can access the Night Vision settings through Camera Settings with the following options: Automatic, Off, or Always On.

Step 1: Go to your Camera’s page on the Kasa App and tap on the settings button

Step 2: Tap on Night Vision

Step 3: Choose your night vision option and tap Save.

*Note: If your camera has been placed in front of a window, you may experience some glare from the infrared LEDs used for night vision. You may need to turn off night vision to the reduce the glare. Placing the camera next to a wall’s edge may also affect how night vision works.

Read More : TP-Link VIGI VMS Ultimate Guide

General Questions related to Kasa Smart Cameras

Part 1：Installation Questions

Do I need an account to be able to use a Kasa Smart camera?

Yes, All TP-Link apps and services require the creation or use of a TP-Link ID. This is a universal account that is used to manage and access your TP-Link apps or services. One account can be used across multiple apps or services, so if you use products such as Deco, Kasa or Tapo all you have to do is create one account to access them all. You can refer to FAQ 1961 for more information.

What are the requirements to use the Kasa App?

Please download and update the latest version of the app from Google Play or the App Store. OS requirements may change with future app releases. Check your app store for information on the latest requirements.

Note: Currently, there are no plans to support other operating systems such as Windows, Mac or Linux. Kasa is only available on Android and iOS devices.

What encryption types do Kasa cameras support?

Kasa cameras currently support WEP, WPA/WPA2, and WPA3(some models) encryptions.

Portal, WPA/WPA2-enterprise, and open/unsecured networks are not supported.

Note: Kasa smart devices do support hidden SSIDs.

What bands do Kasa cameras use?

KC120 and KC200 support both 2.4GHz and 5GHz. All of the other Kasa Cameras support 2.4GHz only.

What do the Kasa Camera’s LED colors mean?

How do I mount my Kasa Camera?

Use the provided mounting equipment and follow the in-app guide for mounting your camera.

Part 2：Motion Detection and Notification Questions

How do I adjust the Camera’s detection sensitivity?

Navigate to the camera Device Settings page on the Kasa App, then tap Privacy and Sensitivity where you can find settings to change the sensitivity of the detection to a lower/higher level.

What does the Notification Frequency option do?

This option allows you to reduce the number of notifications in a particular period of time. One notification for every 5 minutes of activity. This is useful when monitoring a particular busy area.

Why clips or snapshots in the Activity Center when motion detected?

If you are using the local storage option or have not subscribed to Kasa Care you will still receive a notification if activity is detected but there will not be a recording to review in the activity Center.

For local storage go to Cameras > tap on the Camera > tap 24/7 recording to review record activity.

Does Kasa camera support email notification when it detects an activity?

No, Kasa cameras only support Push Notifications.

Part 3：Live View Questions

Who can manage my camera and view recordings?

Only individuals who have signed into the associated Kasa account can view your camera and recordings. All video streams and activities associated with your camera are private and can only be viewed by those signed into the Kasa Account.

*Note: We recommend that you never share your account information with anyone.

Can I view multiple Kasa cameras at the same time?

A preview for all cameras can be found under the Camera tab. Simply tap the play button on each preview to view what the camera is currently looking at.

Can multiple accounts/devices view the Kasa camera at the same time?

Yes, up to 10 users can be logged into your account at the same.

What should I do if the screen of my camera has an abnormal color (pink, purple, green, etc.)?

How long can I view the Live stream of a Kasa camera?

Part 4: Third-Party Questions

How do I view a Kasa camera on a computer?

At this time Kasa Cameras do not support RTSP so viewing a camera’s stream on a computer is not possible.

What 3rd Party Home Assistants are supported?

Bother Google Assistant and Amazon Alexa are supported. This is a cloud-to-cloud integration and you will be required to connect your Kasa Account to their service in order to use voice control or view the livestream on a compatible device, like Nest Hub or Alexa show.

For Amazon Alexa: http://www.tp-link.com/us/faq-1952.html

For Google Assistant: https://www.tp-link.com/us/faq-1558.html

*Note: Refer to this link to know the commands the camera supported. For security purposes on/off commands are not available for voice control.

Part 5: Audio & Video Questions

How do I adjust the volume of the Kasa camera from the Kasa APP?

Tap on the camera tab, then tap on the camera you want to adjust. In the lower right corner you should see a speaker button. Tap and use the slider to adjust the camera’s microphone volume.

What should I do if the audio from the Kasa camera sounds muffled?

Make sure there are no other devices causing interference. If there are you may want to relocate them or the camera.

*Note: view the livestream in the same room as the camera can cause feedback on the speaker

Why there is no audio in the recordings from my Kasa Cam?

Part 6: Recordings & Clips Questions

Does the Kasa camera support manual recording?

Yes, however you will need to have a Kasa Subscription in order to trigger manual recording.

How can I delete recordings of Kasa camera from Kasa APP?

Tap on the Activity tab, then tap on the recording. Tap on the options button and select delete.

Do Kasa Cameras support 24/7 recording?

Yes, all current Kasa cameras support 24/7 recording. This feature requires local storage via a MicroSD card (sold separately).

Can you delete 24/7 recordings using the Kasa App?

When using the 24/7 recording feature the oldest recordings are automatically overwritten. You can delete all contents by reformatting the MicroSD card in use.

How can I download a clip to my PC?

For 24/7 recordings simply take the cameras MicroSD card and using a adapter transfer the contents from the card to your computer

For cloud storage you will need to download the individual clip to your phone and then sync it to your PC or use a cloud storage, like Dropbox or iCloud to access and download the clip to your PC.

Can I restore deleted recordings?

No. Deleted records are not recoverable.

How long will a clip be stored on a MicroSD card?

This depends on the size of the MicroSD card and the video quality used.

Use the chart in this FAQ to choose the right memory card for you.

Part 7: Other Questions

How secure are Kasa cameras?

Kasa Cameras use industry-standard AES 128-bit encryption with SSL/TLS.

How much data will my Kasa camera use when watching live video or uploading the clips to Cloud?

This depends on the resolution used. On average the usage should be no more than 5Mbps

How many Kasa cameras can be managed by one account?

There is no limit unless you are using Kasa Care’s account-based plan. If that is the limit is 10 cameras

What should I do if I’ve forgotten my password?

You can refer to this link to solve your problem.

How do I change the email address of my Kasa App account?

There is no current way to change the email address. You can create a new TP-Link ID, however, you will need to remove the devices from the old account and rebound them to the new one.

*Note: If you are using Kasa Care services you will need to cancel the account and resubscribe under the new account.

How do I switch to another Kasa account in the Kasa APP?

You will need to log out of the current account and login with the new one. Kasa APP ->Me ->View Account -> Log Out ->Login

But please note if your Kasa devices have already been bound to the previous account, you will need to remove those devices first from the old account and bind them to the new one, here is the guide for unbinding them from the old account. Or you could reset the devices manually.

Can I still use my Kasa camera if there is no internet?

You can use the camera or watch the live view without an internet connection, but please ensure both your phone and the camera are connected to the same wireless network.

Note: Motion detection or any other service associated with the TP-Link Cloud will not work if there is no internet access.

How long is a Kasa Camera’s power cord?

10 feet

How do I turn off the camera?

Open the Kasa app and on the main screen tap the “power” button next to the camera. This will enable privacy mode and stop all recording and monitoring until privacy mode is disabled.

How do I turn on or off the green LED on the front of the Kasa camera?

If you want to turn on or off the green LED on the front of the Kasa camera, navigate to your camera’s live view screen and access the device settings. Scroll down to a toggle switch for Status LED.

How do I use Push to Talk (PTT)?

Like a walkie-talkie, you can use a Kasa Camera to communicate with those around the camera. Simply press and hold the microphone button in the Kasa app. Once you hear the chime you can begin to speak. Release the button to allow for the other person to respond.

Why can’t I hear the sound of the camera when clicking the “Push to Talk” button on the camera?

Our camera’s 2-way audio is half-duplex. It can only send or receive at a given time.

Can KC300 and KC310 use the same hub?

Yes! The hub (KH300/KH310) supports both KC300 and KC310 at the same time, the maximum limit of the cameras connected is 16 cameras for 1 hub.

What is the meaning of Class 10 in SD cards?

SD cards are divided into Class 0/2/4/6/10 according to different read and write speeds. Class 10 is one of the faster-speed classes of SD card flash memory. It’s suggested to use an SD card whose read and write speed is Class 10 or above.

How to set up the Schedule feature?

On the live screen, there is the Schedule icon. Customers can set a time to turn off or on the camera.

When the camera is off, its video stream service is disabled, which means you cannot live view, and would not get any detection or notification. The camera is in standby mode.

What’s the subscription plan for Kasa Cam?

The subscription plan is also called Kasa Care. Refer to the FAQ link for details: https://www.tp-link.com/us/support/faq/1962/

KASA SMART CAMERA FAQ

How Do I Remove my Kasa Cam?

.

*Note: All Kasa Cams require and only work with the Kasa for Mobile App

iPhone:

Find your camera on the device list in your Kasa App.  Swipe to the left to remove the camera.

Android:

Find your camera on the device list in your Kasa App.  Select and Hold to Remove.

Through App Settings:

Step 1:  From the Camera’s page, open settings and click Delete on the bottom.

Step 2:  Read the warning and click Delete Device

Note:  Be aware that when you remove your camera the following will take place:

Your Kasa Cam will be removed from your account and restored to factory settings.

All configured settings and notification settings will be removed.

When removing the camera, your existing recordings will not be deleted and your subscription recording plan will remain unchanged.

How Do I Setup my Kasa Cam?

Please following the instructions step by step in this article to go through the entire setup process, then you can control the Kasa Cam with your Kasa app.

Before we begin:

1. Please download Kasa Smart from App Store or Google Play and install it on your smartphone.

2. Connect your smartphone to your home Wi-Fi network.

3. Plug your Kasa Cam into a power socket.

Here we use KC120 for example

Step 1: Open the Kasa App

Log into your cloud account. Please refer to the link to sign up if you don’t have a cloud account.

Step 2: Tap “+” button to add a Kasa Cam, select “Add a Device”, and choose “Cameras” icon according to your model number.

Step 3: Follow the instruction on the Kasa app to power on the Kasa Cam, and wait for the light to blink orange and green.

If the light does not blink orange and green, please reset the Kasa Cam as per UG/QIG.

Step 4: Connect your phone to the Kasa Cam’s Wi-Fi network.

For Andriod:

Kasa will look for your Kasa Cam automatically, and it will take about a minute.

If you have a problem with this step, please go to Settings->Wi-Fi on your smartphone and manually connect to Kasa Cam’s Wi-Fi network (same as iOS).

For iOS:

You need to connect to the Kasa Cam’s Wi-Fi network manually, please go to Settings->Wi-Fi on your smartphone and manually connect to Kasa Cam’s Wi-Fi network (which is named Kasa_Cam_xxxx), and then go back to the Kasa app to continue the setup process.

Step 5: Choose your home network to connect, enter the password of your home network.

Step 6: Name your Kasa Cam

Step 7: Enable Activity Notifications. If you enable this function, your camera can alert you whenever it detects motion. If you don’t want to be notified, click on “I don’t want to be notified”.

Step 8: Follow the instruction to mount your camera. If you do not want to do it now, click on “No Thanks”, and we have completed the setup of Kasa Cam.

Where Can I Place my Kasa Camera

*Note: All Kasa Cams require and only work with the Kasa for Mobile App

Kasa Cam is an indoor only camera that can be placed on any flat surface or vertically mounted using the magnetic base or the mounting accessories provided.

When selecting a location to place your Kasa Cam we suggest an area that has a clear field of view, and no obstacles that may interfere with your viewing experience.  Areas that face your front or back doors are typical locations.

Mounting Options:

Mounting with Magnetic base:

Mounting with Mounting Plate

Placement on a Flat Surface

With the Kasa Cam’s Adjustable arm you are also able to place the camera on any flat surface.

How do I move my camera to a different wireless network?

*Note: All Kasa Cams require and only work with the Kasa for Mobile App

You can change the wireless network by resetting your camera, and then following the regular setup process.

Step 1:  With your camera plugged in remove the back cover.

Step 2:  Using a paperclip press the reset button for 5 seconds.

Step 3:  Once the LED is blinking amber and green launch the Kasa App and click on Add device.

Step 4:  tap Choose from Pre-configured Devices.

Step 5:  You will have an option Reset my Device or Don’t Reset my Device.  If you are just changing the wireless network choose Don’t Reset my Device.

*Note:  Be aware that selecting RESET MY DEVICE will return your camera to factory defaults removing your current camera settings, and will delete all activity and clips associated with your camera.

What are the sensitivity settings and how do I control them?

*Note: All Kasa Cams require and only work with the Kasa for Mobile App

There are two sensitivity settings: Motion and Sound.

Motion sensitivity indicates how little or how much activity must occur to trigger a notification.

Sound sensitivity indicates whether you want to listen for noise or not.

You can access the camera sensitivity settings from the device details page. For motion sensitivity and when sound sensitivity is enabled, your options are more sensitive, normal or less sensitive.

How to View the Recordings on a Kasa Camera

You will need to log in to your Kasa account in the Kasa app to view your camera’s recorded clips.

Note: If the camera enjoys the Kasa Care service, the clips uploaded to the cloud server are maintained based on your Kasa Care subscription plan.

Method 1: Viewing Cloud Recordings

You will be directed to the Live View page of the camera if you tap the Watch Live button.

If you tap the More button on the clip, you can download/Share/Remove the clip.

Method 2:  Viewing Locally Stored Clips

Note:

Related Tags:

“Kasa camera not connecting to wifi”, “Kasa camera offline troubleshooting”, “Kasa camera app login problems”, “Kasa camera motion detection not working”, “Kasa camera night vision blurry”, “Kasa camera cloud recording not saving”, “how to reset Kasa camera”, “how to update Kasa camera firmware”, “Kasa camera compatible with Alexa/Google Assistant”, “Kasa camera subscription cost”, “Kasa camera warranty information”, “Kasa camera installation for beginners”, “troubleshooting Kasa camera network connection”, “common Kasa camera error codes”, “Kasa camera two-way audio not working”, “Kasa camera recording schedule setup”, “Kasa camera field of view adjustment”

To view videos from the mydlink cloud, follow the steps below:

Step 1: Launch the mydlink app.

Step 2: Tap the menu icon in the upper left corner. You can also tap Event & Video at the bottom.

Step 3: Tap Event & Video.

Step 4: Tap Event.

Step 5: At the top, select the day you want to view video from. The videos will be listed newest to oldest and will display if detected by motion or sound. Tap the video to watch it.

Step 6: You can perform the following on the view video screen:

Step 7: Tap back to go back to the list of videos (Timeline). To delete videos, tap Edit in the upper right and then select the videos you want to remove. Tap Remove in the bottom right corner to delete.

.

Note: This Automation example will show you how to setup Recording by Motion.

Step 1: Launch the mydlink app and sign into your account.

Step 2: Tap the menu icon on the top left.

Step 3: Tap Settings.

Step 4: Tap Automation.

Step 5: Tap the + sign.

Step 6: Tap the + sign to add a new rule.

Step 7: Tap the icon next to the trigger type you want (motion or sound detection), then tap Next. In this example, the DCS-8000LH motion detection is selected.

Note: You can select multiple events.

Step 8: Tap the icon next to the event action you want, then tap Next. In this example, Recording (records video to the cloud) and Push Notification (sends a push notification to the device with the mydlink app) are selected.

Note: you can select multiple actions.

Step 9: Tap Save.

Step 10: Tap Go Ahead.

Step 11: Your new automation will appear. Tap on the circle icon under Rule 1 to edit any events and/or actions. Tap the trash can icon in the upper right corner to delete the entire Automation.  You can create multiple rules for each Automation. Click the + in the lower right corner and repeat steps 7-10).

Next to the automation name, tap the > to rename and select a different icon (shown next to Automation 1 in the example).

Select which camera line you would like to set up sound detection:

Mydlink app setup guide v1

– DCS-8xxxLH Series

– All other DCS cameras

The following is for the DCS-8xxxLH series cameras. Note that the DCS-8200LH is not compatible with the mydlink app. You must use the mydlink Home app.

Step 1: Launch the mydlink app.

Step 2: Tap the menu icon in the upper left corner.

Step 3: Tap Settings.

Step 4: Tap Automation.

Step 5: Tap the + sign.

Step 6: Tap the + sign to add a new rule (or add to an existing rule).

Step 7: Tap the sound detection trigger and then tap Next. Note you can click the > icon to set the sound level to trigger.

Step 8: Tap the event action(s) you want, then tap Next. In this example recording (cloud) and push notification are enabled.

Step 9: Tap the check mark or Save on the top right, then tap Go ahead.

.

The following is for non-DCS-8xxxLH cameras.

To enable sound detection, follow the steps below:

Step 1: Launch the mydlink app.

Step 2: Tap Devices at the bottom of the home screen or tap the menu in the upper left corner, tap Devices.

Step 3: Tap Camera.

Step 4: Select the camera from the dial and then tap the gear icon.

Step 5: Make sure the microphone is turned on. Tap Sound Detection.

Step 6:Tap the Sound Detection button to turn on if grayed out.

Step 7: The current level of noise will be displayed. To change the noise level at which you want it to trigger, tap and slide the black dot up or down to the desired level. Tap < (iOS) or tap the back button (android) to save.

Step 8: Tap OK.

Step 9: Verify that sound detection is ON.

.

When you first install your camera, motion detection as well as the automation rule (record and notification) is automatically setup. To enable/edit motion detection, follow the steps below:

Step 1: Launch the mydlink app.

Step 2: Tap Devices at the bottom of the home screen or tap the menu in the upper left corner, tap Devices. You can also tap the camera in your shortcuts and tap the live video to access the camera settings (skip to step 5).

Step 3: Tap Camera.

Step 4: Select the camera from the dial and then tap the gear icon

Step 5: Tap Motion Setting.

Step 6: Tap where you want to detect motion (represented by a orange square). Then select the sensitivity (0-100, 100 being the most sensitive). Once finished, tap < (iOS) or tap the back button (Android) to save your settings.

Step 7: Your settings will be saved.

Note: To turn “off” motion detection, tap the Clear All button, and then change the sensitivity to 0. Tap back to save your settings.

.

To setup your camera with the mydlink app, follow the steps below:

Step 1: Launch the mydlink app. Log in with your mydlink account username and password. This will be the same username and password if you have used the mydlink Lite or mydlink Home app. If you have never created a mydlink account, you can create one.

Step 2: Tap the settings icon (3 lines in the upper left corner).

Step 3: Select Add a Device.

Step 4: Tap Yes to scan the QR code.The QR code is located on the label on the bottom of the camera or on the Wi-Fi configuration card included with the product. If the label or card are missing, tap No and select from the drop-down list.

Step 5: If you tapped Yes, scan the QR code. If you are having trouble scanning the QR code, move to a brighter lit area. If you tapped No, select the camera model from the list.

Step 6: Tap Next. Please wait about a minute (or less).

Step 7:  Tap Device Location to select where your camera will be setup. Select from the list or scroll to the bottom and tap Add Location to create your own.

Step 8: Tap Choose Your Wi-Fi Network. Select the WiFi network you want to connect the camera to (note this should be the same network that your mobile device running this app is on). Enter the Wi-Fi password and then tap Next.

Step 9: If you want this camera to be displayed on the “Home” screen, tap Add to Shortcut (checked by default). Tap Next at the bottom to continue.

Step 10: The camera will now save your Wi-Fi settings, and then bind to your mydlink account. This process can take up to 3 minutes.

Note: If you receive an error during the Setup Wi-Fi process, make sure you are entering the Wi-Fi password correctly. Remember it is case-sensitive. Also make sure the camera is within range of your wireless router, and that the router has DHCP enabled and does not have any filtering which may block the camera from connecting.

If you receive an error during the Binding process, this usually means the camera cannot connect to the mydlink servers. It is best to reboot your router, close the mydlink app, and reset the camera (hold a paperclip in the reset hole for 10 seconds and release. The LED on the back should turn red). Once your router has rebooted, open the mydlink app and set it the camera again. If you continue to get errors, please contact D-Link support at 1-877-453-5465. Support is free and available 24/7.

Step 11: Once the camera setup is finished, the following message will appear. If you want to add the camera to cloud recording, tap Yes, or tap Later.

Step 12: If you tapped Yes, a new Automation will be created to record video detected by motion to your cloud recording subscription (free or paid). Tap the check mark at the top right corner to finish setup.

.

Note: This Automation example will show you how to setup Recording by Motion.

Step 1: Launch the mydlink app and sign into your account.

Step 2: Tap the menu icon on the top left.

Step 3: Tap Settings.

Step 4: Tap Automation.

Step 5: Tap the + sign.

Step 6: Tap the + sign to add a new rule.

Step 7: Tap the icon next to the trigger type you want (motion or sound detection), then tap Next. In this example, the DCS-8000LH motion detection is selected.

Note: You can select multiple events.

Step 8: Tap the icon next to the event action you want, then tap Next. In this example, Recording (records video to the cloud) and Push Notification (sends a push notification to the device with the mydlink app) are selected.

Note: you can select multiple actions.

Step 9: Tap Save.

Step 10: Tap Go Ahead.

Step 11: Your new automation will appear. Tap on the circle icon under Rule 1 to edit any events and/or actions. Tap the trash can icon in the upper right corner to delete the entire Automation.  You can create multiple rules for each Automation. Click the + in the lower right corner and repeat steps 7-10).

Next to the automation name, tap the > to rename and select a different icon (shown next to Automation 1 in the example).

.

To view videos from the mydlink cloud, follow the steps below:

Step 1: Launch the mydlink app.

Step 2: Tap the menu icon in the upper left corner. You can also tap Event & Video at the bottom.

Step 3: Tap Event & Video.

Step 4: Tap Event.

Step 5: At the top, select the day you want to view video from. The videos will be listed newest to oldest and will display if detected by motion or sound. Tap the video to watch it.

Step 6: You can perform the following on the view video screen:

Step 7: Tap back to go back to the list of videos (Timeline). To delete videos, tap Edit in the upper right and then select the videos you want to remove. Tap Remove in the bottom right corner to delete.

.

Step 2: Tap the menu icon in the upper left corner.

Step 3: Tap Cloud Recording.

Step 4: Tap Subscribe.

Step 5: Choose an Available Plan.

Step 6: Tap Subscribe Now.

Step 7: Tap OK.

Step 8: Tap Next.

Step 9: Select the camera you want to enable the cloud recording for, then tap on the    on the top right.

Step 10: Tap the   on the top right .

Step 11: Click here to set up recording on your camera.

.

To add additional cameras with Cloud Recording follow the steps below:

Step 1: Tap the menu icon on the top left.

Step 2: Tap Cloud Recording.

Step 3: Tap the gear icon.

Step 4: Select the additional camera(s) you want to enable Cloud Recording for then tap  

Step 5: Tap Set a Rule.

Step 6: Tap the settings icon.

Step 7: Tap the + on the bottom right to add a rule for the new camera.

Step 8: Select the event you would like to a add to your automation, then tap Next (This example shows motion detection).

Step 9: Select the action you would like to add to your automation, then tap Next (This example shows Cloud recording and Push Notifications).

Step 10: Tap 

Step 11: Now you can see the two Rules for the two cameras.

.

When you first install your camera, motion detection as well as the automation rule (record and notification) is automatically setup. To enable/edit motion detection, follow the steps below:

Step 1: Launch the mydlink app.

Step 2: Tap Devices at the bottom of the home screen or tap the menu in the upper left corner, tap Devices. You can also tap the camera in your shortcuts and tap the live video to access the camera settings (skip to step 5).

Step 3: Tap Camera.

Step 4: Select the camera from the dial and then tap the gear icon

Step 5: Tap Motion Setting.

Step 6: Tap where you want to detect motion (represented by a orange square). Then select the sensitivity (0-100, 100 being the most sensitive). Once finished, tap < (iOS) or tap the back button (Android) to save your settings.

Step 7: Your settings will be saved.

Note: To turn “off” motion detection, tap the Clear All button, and then change the sensitivity to 0. Tap back to save your settings.

App Download

Simply download the Vichome app from the Apple Store (iOS devices) or Google Play (Android devices) and have full control over all security products. This means that you can monitor your home or property whenever you like.

As a powerful helper, our app will help you stay connected to your home or business when you’re not there and help keep you safe when you are.

NOTES🚩: Vicohome APP is a mobile application and we currently do not provide PC version or iPad version of the APP.

We greatly appreciate your support and welcome to stay tuned for more.

LongPlus Camera Setup Guide

🔎DOWNLOAD  TODAY📲

【OR】Press and hold this QR code to automatically identify and install

How to properly install the security camera?

🟠 When installing security cameras, LongPlus always recommends placing cameras up high. The outdoor installation location should be 7ft away from the ground. Here are the best places to install security cameras around your home: front & back doors, garage & driveway, yard, common areas, main stairway or hallway, or any side doors or large first-floor windows that an intruder could gain access through.

🟠 Typically, home cameras are placed in the corners of the room to optimize the viewing angle. LongPlus recommends at least two cameras to fully cover a large space, such as a living room. To fully monitor your home, users can add cameras in each room to achieve a complete home monitoring system.

🟠 Battery cameras can not be installed behind a window/glass if you want to use the “Motion Detection” feature.

Battery cameras use PIR (passive infrared) motion detection, an energy-efficient (saving battery power) technology that captures motions by detecting infrared radiation (radiant heat) emitted or reflected by objects. When the camera is mounted behind a window/glass, infrared radiation does not pass through the window/glass. As a result, the “Motion Detection feature” does not work reliably. If you want the camera to detect motions outside, it is recommended that you mount the camera outside.

For plug-in/wired cameras, the answer is yes, as they use camera video analytics rather than PIR sensors to detect motions. As long as they “see”, they can detect motions. So you can mount the camera behind a window/glass with confidence.

How to find the serial number of LongPlus security camera?

🟠 Each LongPlus security camera has a serial number. These are usually located on the body label of the security camera, starting with S/N:*****. Also, if you’ve added your camera to the app, you can also tap the camera “setting” icon > tap the “>” extension icon > tap the “More info” button to find the camera’s serial number.

Is LongPlus security camera waterproof?

🟠 Yes. The waterproof rating of LongPlus camera is IP65. It can be “protected against water jets from any angle”. Generally, the camera can be used outdoors on ordinary rainy and snowy days. However, it may get damaged in extreme weather. But if the camera is installed under the roof or in a place with some shelter, it can get protection to a certain extent. Besides, please don’t expose the camera’s charging port, power button, and microSD card slot to water.

What do the indicator lights on LongPlus security camera mean?

🔵 Solid Blue Light – The camera is working properly.

🟡 Solid Yellow Light – The camera is charging.

🟢 Solid Green Light – The camera charging is complete.

⚪ No Light – The camera is in sleep/off mode.

Can I talk to someone via LongPlus App?

🟠 Yes, LongPlus security camera features two-way audio capability, which means you can listen and talk to someone in real-time with simple clicks in the App.

Do LongPlus security cameras need an app to work?

🟠 Yes! All LongPlus smart security cameras are connected to the LongPlus APP. Compatible and compatible with the latest versions of iOS/Android devices. Installing LongPlus app is a breeze and it comes with voice prompts to guide you step-by-step in minutes.

What is the default language of LongPlus security cameras?

🟠 The default language of LongPlus security camera is set during production and testing in the factory production process. After connecting with LongPlus APP, the language of the camera will follow the language of the APP.

Can I see the infrared light at night?

🟠 No, the night vision infrared light is invisible to human eyes. If you turn on your phone’s camera and point it at the camera lens, then you will be able to see it.

How to format a Micro SD card?

🟠 Sometimes after inserting a Micro SD card, the camera will report “Please use the app to format your SD card first”, that’s because your Micro SD card is not the FAT32 format that the camera supports. In this case, please tap the camera Setting icon > tap SD card > tap Format to format it.

How to record/save videos on a Micro SD card?

🟠 Installing a Micro SD card does not mean the camera will record a video to the Micro SD card all the time.

When the camera detects a movement, it will record a video to the cloud and the cloud recording will display in the Library in the app. If apart from the cloud recordings you want to save backup videos on a Micro SD card at the same time, you can insert a Micro SD card into the camera.

🟠 Here are tips:

1. Find the Micro SD card slot and insert your Micro SD card: Mostly, the Micro SD card slot is next to the power button and is under the rubber plug of the camera body. However, for some models of cameras, you may need to take off the outer shell of the camera to find the Micro SD card slot.

2. If the Micro SD card is detected, you will hear “SD card detected” at the time when it is inserted, and you can see both the storage of the Micro SD card and “SD Card Video” in the app.

Please note that the camera only supports legitimate brand-name (SanDisk, Samsung, Kingston) Micro SD cards, but may not be able to support no-brand, fake, expansion (the storage is extended), and read-only (you aren’t able to put a file to it) Micro SD cards.

How to view videos on the Micro SD card?

You can view videos on the Micro SD card from the app or on your computer.

To view videos on the Micro SD card from the app, please tap the camera “setting” icon on the app homepage > tap “SD card video” on the “Camera Setting” page > select the date on the top > swipe the screen left and right until the green vertical line overlaps the grey “bubble”( If there is no grey “bubble”, that means there are no motions detected in that period).

If you want to zoom in on the specific time before playing a video, you can swipe two fingers left and right at the same time or tap the “magnifying glass” icon.

How to activate cloud storage?

🟠 The cloud storage we gift you is automatically activated and contains free 3 days rolling cloud storage. You can view the cloud-stored videos in the last 7 days at any time.

When the SD card is full will it overwrite the older files?

🟠 Yes, when the SD card is full, the camera will delete the earlier recorded video so you don’t need to format the SD card manually.

Can the camera be used without a memory card?

🟠 Without a memory card, the recorded video will be automatically saved in the cloud, you can watch the video for nearly 7 days in the cloud.

How long does it take to charge LongPlus camera once?

🟠 It will take about 8 -15 hours to fully charge the camera once. When the security camera is fully charged, the indicator light will turn solid green.

Why can’t the battery be charged?

🟠 The following factors may cause charge failure. Please check them one by one:

(1) The charging device is not suitable, or it malfunctions. Please make sure the power adapter and charging cable are in good condition. The power adapter specification is “5V/1.5A”.

(2) The charging port is defective. Possible causes include: the Micro USB cable and the charger or the charging port of the camera are not plugged in properly; there are objects in the charger or the charging port of the camera.

(3) Please confirm whether there are objects in the camera’s charging port or the charger port and clean it before charging.
Please ensure that the Micro USB cable is in good contact with the ports on both ends of the charger and camera.

(4) You can try to connect the Micro USB cable and the charger to other devices (such as mobile phones or computers) to see if they work normally. If anyone doesn’t work, please change to a new one to try again.

(5) The long-time operation leads to charge port oxidation or internal looseness. Please repair or replace the charge port immediately.
The charging cable is damaged or broken. Please replace the Micro USB cable that can work normally.

(6) The charging cable should not be too long. The required cable length is generally not more than 16 feet (5 m). Please replace the Micro USB cable with a suitable length.

(7) The charging environment is not suitable; excessively high or low temperature makes charging impossible. Please move to a place with an appropriate temperature environment (0°C ~ 45°C) for charging.

If the above are ruled out but the issue still persists, please submit feedback from the app for further technical assistance.

Why can’t the battery be used for a long time?

🟠 The battery life mainly depends on the total working duration of the camera. The following factors may lead to fast battery consumption. Please check them one by one:

1. Users frequently view live streams/The camera is frequently activated to record videos.
In order to make the camera work longer, please avoid turning on the live broadcast for a long time.

2. Poor Wi-Fi connection to the camera
If the camera’s Wi-Fi connection is bad or unstable, it will continue to actively search for networks, so the battery will drain quickly.
Please try to place the camera near the Wi-Fi router. Thick walls, bricks, ceramics, electromagnetic equipment, large amounts of liquid, and large metal objects can interfere with Wi-Fi signals. Please try to avoid these objects.

3. Extremely cold weather shortens battery life
The operating temperature of the camera is -10°~45 °C. Please do not place the camera in an extremely cold environment.

4. Night Sight will consume more battery power
When you enable Night Sight, the camera will enter night mode when the light is darker than the threshold (sensitivity level). Camera performance is improved when it is dark.
Therefore, for sharp nighttime images, we don’t recommend disabling it, although it may drain more battery power. But if you still want to disable it, you can tap the camera “Settings” icon > tap “Lighting Settings” > close “Night Sight”.

How can I extend the battery life?

🟠 The battery life is largely determined by the number of recordings and the number and duration of live. Here are the suggestions to extend the battery life:

(1) To reduce false triggers. Change the location or angle of the camera. Please allow us to explain how motion detection works: when the PIR sensor perceives a change in the environment, motion detection will be triggered. The change in the environment can be a moving object, light change, the alternation of hot and cold air, etc. Particularly common false triggers include trees shaking after being blown by the wind, the cold air of the air conditioning, etc.

(2) Set motion detection sensitivity to Low or Medium. After doing that, the distance the PIR sensor can detect will become shorter so that false triggers may be reduced.

(3) Shorten the recording duration of the camera. Currently, the camera-supported recording durations are 10 seconds, 15 seconds, 20 seconds, and automatic (up to 3 minutes). For your reference:

(4) Set Sleep mode. This feature allows you to schedule the working hours for the camera. Whether the camera enters sleep mode on schedule, or you enable Sleep, the camera will be deactivated. Under this condition, the live feed will not be accessed, motion detection (including push notifications, recordings, and camera alarm) will stop working. This can reduce power consumption to save battery life.

(5) If possible, you can try to watch live feeds or adjust camera settings on your mobile phones less frequently.

(6) To avoid or reduce the battery consumption caused by poor network connection. You can place the camera as close to the router as possible, and try to avoid thick walls, bricks, ceramics, electromagnetic wave equipment, a large amount of liquid, and large metal objects.

(7) We suggest that the camera be installed in a suitable temperature environment (14°F~113°F).

(8) It is generally not recommended that you turn off night vision, but if you do not need to monitor at night (watch live and video), you can turn off night vision.

If the issue persists, please submit feedback from the app for further technical assistance.

Will Wi-Fi environment affect the camera battery?

🟠 Yes, an unstable or poor network environment will cause the camera to transmit data multiple times, the camera keeps actively searching for the network, or even reconnect to Wi-Fi continuously, which will result in faster battery consumption. Multi-layer concrete walls, brick walls, and overcrowded Wi-Fi channels will cause a bad Wi-Fi environment.

To save the camera’s battery life, please ensure that the network connection is strong.

How to charge the camera?

🟠 Connect the Micro USB cable to a 5V/1.5A power adapter.

🟠 Connect the other end of the USB cable to the camera.

🟠 Plug the power adapter into an electrical outlet.

🟠 Use the solar panel to charge.

Battery cameras can be used after being fully charged

How to install and use Camera Live on a compatible Windows or Mac PC/laptop

Camera Live is a free program for you Windows PC or Mac that can be used to locate its local IP address and to view the camera’s live feed locally and remotely. 

First download the appropriate installation file from the links below and install the program.

For a Windows PC click here

For a Mac click here

Once you have installed the program, open it and click on Add Video. Then click on Discover to find the cameras UID, or enter it manually ensuring it is correct and all in uppercase. Enter the cameras password ensuring this is correct and in the correct case. Then give the camera a name e.g. garden, drive etc. and click on OK.

Once added wait for the camera to connect to the program. When it is connected you will see a green icon next to the UID, you can then view your camera’s live feed by clicking on the play icon. You will see the “No Video” message until you have viewed the live feed for the first time and the program can produce a thumbnail image from this.

.

Forgotten your password or getting a wrong password message?

If a password has been forgotten unfortunately there is no way to recover these as this would compromise the camera security.

The default username and password for the camera will be “admin” e.g.:

Username:     admin
Password:      admin

We recommend trying these first to see if they allow you to login. 

These must be entered all in lowercase and should be double checked as some devices such as iPhones/iPads will set the first letter to uppercase automatically.

When changing the password this should be in alphanumeric characters (i.e. a,b,c… 1,2,3…) only with no special characters or spaces.

If the default password has been changed you cannot recall what you set it to you will need to reset the camera to the factory defaults to regain access. 

NB: When you reset a camera it will reset it to factory defaults (and will lose the WiFi details you currently have set) so you should only perform a reset while your camera is connected to your router with an ethernet cable.

To do this can you:

1) Remove all cables connected to the camera.
2) Remove any SD card from the camera.
3) Wait 10 mins.
4) Connect the ethernet cable to the camera and your router, you should hear a click when the cable is connected.
5) Wait 2 mins.
6) Connect the power cable to the camera.
7) Wait 5 mins for the camera to power up.
8) Locate the camera’s reset button or recess.

For the outdoor camera this will be a button on the underneath of the camera or on the end of a cable.
For the indoor camera this will be a recess on the back of the camera that can be pressed with a paperclip or similar.

9) Press and hold for 20 seconds and release.
10) Wait 5 mins for the camera to reset ensuring it remains connected to your router with the ethernet cable throughout.

Then once the camera is reset can you log in to the camera interface using the default username and password which is “admin”

As the camera has been reset it will be at the factory defaults once again, so you will need to setup your camera again with the WiFi details, etc. as if from new.

To do this take a look at the setup guides in the section below.

Having touble setting up your camera to record to SD card/NVR/NAS drive.

Are you looking to setup recording? If so please see the links below for full setup guides for each recording method. If you have already set it up but have encountered an issue it may be worthwile running through the setup once more, to check for any errors or mistakes.

SD card recording

UCAM NVR recording

NAS Drive recording

If you are still seeing an error or it is not working as expected please take a look at the common issues and their solutions in the list below.

.

SD card not supported or faulty.

Motion detection page not configured correctly

NAS details not entered accurately.

NVR IP address may have changed.

Incorrect Task Management setup

How can I transfer video clips from an SD card in the camera to my computer?

If you are looking to transfer recordings from an SD card installed in the camera to you computer over WiFi this is limited to one file at a time for practical reasons:

.

1) If your SD card had, for example, 128GB of clips it would not only be very cumbersome to transfer that quantity to your computer over your local WiFi but potentially slow down your local network too. As SD cards have very limited file speeds transferring this magnitude of data may also take a very long time to offload.

.

2) It is also impractical or unwise to transfer en masse as it would also cause a slow down of the camera’s capabilities for the time while the transfer is progressing, and your camera could miss key motion events from being recorded.

.

Solutions? There are a number of options available to you:

.

– You can browse the recordings stored on your camera directly from a web browser and check which recordings are important to keep. You can play back the clips in your browser without needing to download to your computer first. Click here for a guide on how to do this.

.

– You can set the sd card to auto overwrite so that it automatically deletes the oldest recordings when the card is full, so you don’t have manually delete.

.

– You can use a number of tasks in the camera to automatically offload clips from the sd card (before they get overwritten) to Dropbox, your own FTP server, etc.

.

– If you really must download everything off the SD card the easiest and quickest way is to take the sd card out and insert directly into your computer (if it supports SD media) and then simply drag and drop the files off the card to your computer.

.

These are but a few suggestions. If you need further advice on the full range of recording and playback options do get in touch with our Support Team and they will be delighted to help.

Cannot connect to the camera remotely using the app.

Are you having trouble connecting to the camera using the app on your phone? This may be a p2p error. The camera and app use p2p to connect, if the camera is unable to connect to the p2p server then it will not be viewable via the app. Click here to check and resolve this.

.

Has the camera been set to a static IP? We do not recommend setting the camera to a static IP as this is not usually required and can render the camera inaccessible if setup incorrectly. Click here to check this has been setup correctly. 

.

Is the UID correct and all in uppercase? If any character in the cameras UID is not in uppercase it will not be able to connect to the app remotely. If this is the case, delete the camera from the app and add it again. For help with this click here for an Android device and click here for an iOS device.

Changed WiFi router or given a new router by your ISP?

If for some reason you have changed/updated your WiFi router your camera(s) will need to be reset to factory defaults and setup again, since the WiFi details and ip addressing on your camera(s) will still be that of your old router.

To reset your camera(s) and start afresh please click here.

NB: Be sure to read and follow the reset instructions carefully to avoid any problems or delay in setup.

.

Once reset you will need to setup the WiFi connection again. Please follow one of the guides below to complete this.

PC Method

App Method

.

WPS Method, for WPS enabled routers.

Power LED flashing rapidly and camera offline?

A rapidly flashing green power LED usually indicates that the camera’s firmware has encountered an error. This is rare but can occasionally happen after an unexpected power cut (if the camera is in the middle of performing a task), due to incorrect settings in the camera (too many enabled tasks, conflicting settings etc.), or due to a faulty SD card. 

This can usually be resolved with a reset of the camera. To do this first power down the camera and leave it for at least 10-15 minutes, then follow the steps on the page linked below to reset the camera. Note: a reset will clear all changed settings in the camera and revert it back to the defaults.

How to reset the camera

If the reset does not clear the error then you should get in touch with our support team using the “contact us” form as they will be able to advise on the next steps to resolve the issue.

How to install and use Camera Live V1

How to reset a camera.

If you think you need to reset your camera we recommend you first get in touch with us using the “Contact us” form as a reset may not solve your issue and will wipe the camera of any user data, meaning you will need to set the camera up again.

But should you want to reset your camera anyway please use either of the guides below.

NB: When you reset a camera it will reset it to factory defaults (and will lose the WiFi details you currently have set) so you should only perform a reset while your camera is connected to your router with an ethernet cable.

.

There are two ways to reset the camera: physically by pressing the hardware reset button or digitally via the camera’s web interface….

.

Physical reset procedure

1) Remove all cables connected to the camera.
2) Remove any SD card from the camera.
3) Wait 10 mins.
4) Connect the Ethernet cable to the camera and your router, you should hear a click when the cable is connected.

5) Wait 2 mins.
6) Connect the power cable to the camera.
7) Wait 5 mins for the camera to power up.
8) Locate the camera’s reset button or recess.
For the outdoor camera this will be a button on the underneath of the camera or on the end of a cable.
For the indoor camera this will be a recess on the back of the camera that can be pressed with a paper-clip or similar.
9) Press and hold for 20 seconds and release.
10) Wait 5 mins for the camera to reset ensuring it remains connected to your router with the Ethernet cable throughout.

Then once the camera is reset can you log in to the camera interface using the default username and password which is “admin”

Digital reset procedure

1) Remove all cables connected to the camera.
2) Remove any SD card from the camera.
3) Wait 10 mins.
4) Connect the Ethernet cable to the camera and your router, you should hear a click when the cable is connected.
5) Wait 2 mins.
6) Connect the power cable to the camera.
7) Wait 5 mins for the camera to power up.

8) log in to the camera interface on a PC, see the guide here on how to do this.

9) Go to Setting, Tools, Backup or Reset.
10) Click on Reset, then when it appears click on Reboot.
10) Wait 5 mins for the camera to power up fully, ensuring it remains connected to your router with the Ethernet cable throughout.

Then once the camera is reset can you log in to the camera interface using the default username and password which is admin (in lower case) for both.

As the camera has been reset it will be at the factory defaults once again, so you will need to setup your camera again with the WiFi details, etc. as if from new. You’ll find the details here: http://ucam247.helpsite.io/categories/3646-camera-setup

Forgotten your password or getting a wrong password message?

If a password has been forgotten unfortunately there is no way to recover these as this would compromise the camera security.

The default username and password for the camera will be “admin” e.g.:

Username:     admin
Password:      admin

We recommend trying these first to see if they allow you to login. 

These must be entered all in lowercase and should be double checked as some devices such as iPhones/iPads will set the first letter to uppercase automatically.

When changing the password this should be in alphanumeric characters (i.e. a,b,c… 1,2,3…) only with no special characters or spaces.

If the default password has been changed you cannot recall what you set it to you will need to reset the camera to the factory defaults to regain access. 

NB: When you reset a camera it will reset it to factory defaults (and will lose the WiFi details you currently have set) so you should only perform a reset while your camera is connected to your router with an ethernet cable.

To do this can you:

1) Remove all cables connected to the camera.
2) Remove any SD card from the camera.
3) Wait 10 mins.
4) Connect the ethernet cable to the camera and your router, you should hear a click when the cable is connected.
5) Wait 2 mins.
6) Connect the power cable to the camera.
7) Wait 5 mins for the camera to power up.
8) Locate the camera’s reset button or recess.

For the outdoor camera this will be a button on the underneath of the camera or on the end of a cable.
For the indoor camera this will be a recess on the back of the camera that can be pressed with a paperclip or similar.

9) Press and hold for 20 seconds and release.
10) Wait 5 mins for the camera to reset ensuring it remains connected to your router with the ethernet cable throughout.

Then once the camera is reset can you log in to the camera interface using the default username and password which is “admin”

As the camera has been reset it will be at the factory defaults once again, so you will need to setup your camera again with the WiFi details, etc. as if from new.

To do this take a look at the setup guides in the section below.

Camera is rebooting often

Do you find the camera does not remain online for any length of time? If so this is usually a setup or a hardware error, typically with the SD card or the recording setup. Please take a look at the troubleshooting guides below to help resolve your issues.

.

SD card not working.

Too many tasks enabled.

Issues with power supply, outdoor cameras.

Cannot view the video from the app.

If you are having trouble viewing video in the app it is likely due to one of the issues listed below. 

Poor Wifi connectivity

p2p disabled

Privacy mode enabled blocking access to the live feed.

Live feed or playback is jerky and not smooth

The first thing to check will be that the camera has a strong WiFi connection. This can be checked in the app by going to Edit Camera, Advanced Setting, WiFi Setting and should be at least 50-60%. A poor WiFi signal can cause the playback of the live feed to be poor. Click here for advice if the WiFi signal strength is poor.

.

If the WiFi connection is strong, the next thing to check will be that the stream setup is set appropriately for your network. The defaults for this are below and can be found by logging in to the camera’s web interface and going to Setting, Camera, Stream Setup.

.

The H.264 bitrate should be left at the default of 1536, raising this can cause the camera to send more data than your router can cope with causing a jerky live stream.

The MJPEG stream should not be set higher than the default of 50. This is an uncompressed stream that is used for the cameras motion detection, not for recording or streaming, raising this can cause issues with the streaming as it puts a high load on the camera.

.

You should also check that you do not have too many tasks enabled, conflicting tasks can cause issues with the camera’s ability to stream well. You should only have one of task 7, 8, 9 or 10 enabled at any one time. For more information on setting up the task management page click here.

NVR IP address keeps changing.

You have setup and NVR with a camera successfully however it stops recording after a short time.

This may be due to your router assigning the NVR a new IP address very often. In this case the best way to prevent this from changing and your details in the Storage Setup page becoming incorrect is by setting the NVR to a static IP address.

To do this please take a look at our setup guide for Setting the NVR to a Static IP address.

Having Trouble With WiFi setup?

Does your WiFi use older WEP Encryption? If so click here

.

Not getting a wireless connection where you have placed your camera? Click Here for more information.

Here’s a breakdown of the concept:

There are different levels of sophistication in IP camera analytics and detection. Here are some examples:

IP camera analytics and detection can be a valuable tool for security and surveillance applications. It can help to reduce false alarms, improve efficiency, and provide more actionable insights from video footage.

People Analytics

People Analytics

Learn how to use Verkada People Analytics to filter people by specific attributes

Updated over a week ago

The Verkada People Analytics feature uses powerful edge-based camera capabilities to detect people, faces, and filter results based on clothing color, apparent sex, and the presence of backpacks.

Note: See User Guide for People Analytics for best practice guidelines.

Enable the People History feature

All Verkada cameras perform people detection (as outlined above) out of the box. However, to enable more complex analytics, such as the ability to search for faces or for people by clothing color, you must enable the People History feature.

Required. To begin, you need to enable the feature globally on your org and then on the individual cameras.

Enable People Analytics Globally

Enable People Analytics on individual cameras

View Person History

When enabled, a Person History can be seen on individual cameras and across all cameras in your organization.

IP Camera Analytics and Detection Setup Guide v1

View Person History for an individual camera

View Person History across all cameras

Use Face Search

When enabled, a Face Search can be seen across all cameras in your organization and on the Verkada Command mobile app.

Use Face Search across all cameras

The Face Search feature is enabled, by default, when you toggle on High Resolution Image Capture. You can search a face across all cameras in your organization.

Use Face Search on the Command mobile app

See Face Search on Mobile Apps to perform a face search on the Command mobile app.

Bulk enable People History on the Devices page

People and Face Search on Mobile Apps

People and Face Search on Mobile Apps

Learn how to use people and faces on Verkada mobile apps

Updated over a week ago

Access People History search

Access a Face Search

License Plate Recognition Overview & FAQ

License Plate Recognition Overview & FAQ

Learn the License Plate Recognition functionality and use cases

Updated over a week ago

Specially-placed cameras are designed to capture license plate images and provide users with a readable and searchable list of license plate numbers. These license plate captures can be linked to live or recorded video from a nearby camera for complete context surrounding vehicle events.

Verkada’s License Plate Recognition (LPR) allows real-time license plate monitoring and logging for later reference. Learn how to configure LPR for your cameras.

Notes:

Key features

Investigate License Plates of Interest

You can use LPR to quickly search for all historical appearances of a license plate, making it easier to complete investigations for suspect vehicles.

Receive License Plates of Interest alerts

With Verkada’s LPR solution, you can receive License Plate of Interest alerts when a specific license plate is detected at any of your locations. You can also send these notifications to third-party applications through the Verkada Webhooks API.

Export results via API integrations

Verkada’s LPR results can be systematically exported to third party systems leveraging our API integrations. This allows customers to run custom business reports or integrate with other critical parts of their security infrastructure.

FAQ

Will Gen 1 Bullet cameras provide the same level of LPR performance as the current, Gen 2 models?

Is it possible to use cameras in LPR mode for video security beyond LPR mode?

Is it necessary to use a Bullet camera as the context camera in a dual-camera LPR setup?

What is the function of a context camera and when is it necessary to use one?

When is it necessary to use an external IR illuminator for capturing license plates and what model should I choose?

What is the camera’s behavior in the event of an internet outage?

Is it possible to integrate a Verkada LPR camera into an external system, such as a tolling system?

What types of license plates are incompatible with Verkada’s LPR technology?

Why is my camera feed too dark at night?

Enable Vehicle Analytics

Vehicle analytics uses powerful edge-based capabilities to detect vehicles and filter results based on vehicle color and body type.

How it Works

Vehicle analytics leverages the cameras’ powerful onboard processing capabilities to detect the presence of, and analyze the properties of vehicles as they appear in the frame. As vehicles are detected, high-resolution images are taken and analyzed for vehicle objects. Selected images are then sent to Verkada’s cloud-based Command platform, where users can filter historical clips for vehicles and search for specific vehicles by time, date, body type, and color.

All Verkada cameras perform vehicle detection (as outlined above) out of the box. However, to enable more complex analytics, such as the ability to search for vehicles by color and body type, vehicle analytics must be turned on.

1.In Verkada Command, go to All Products > Cameras.

2.Select a camera.

3.Select Settings> Analytics.

4.Toggle on Vehicle History.

Bulk enable People History from the Devices Page

Vehicle analytics for an individual camera

Vehicle analytics across all cameras

People and Vehicle Motion Search

People and Vehicle Motion Search

Learn now to search paths of people and vehicles with advanced motion search

Updated yesterday

Verkada’s people and vehicle search features use advanced computer vision functionality to identify people and vehicles within the camera’s field of view and quickly find relevant events.

The Verkada Command UI enables instant video replay previews and trajectory viewing. Trajectory analysis features offers possibilities for searching events, reduces the number of missed detections, improves the detection distance, and reduces duplicates.

View people and vehicles over a timeline

Required. You must have Site Viewer and Site Admin access to view the Motion tab under the camera feed. Learn more about Roles and Permissions for Cameras.

You can view people and vehicles detected by a Verkada camera within historical footage.

1.In Verkada Command, go to All Products > Cameras.

2.Select a camera to view its feed.

3.At the top, click Motion.

4.To the right, click Show Pathsto toggle on/off the feature.

5.(Optional) Make a selection on the video player grid to search for motion in the area.

6.(Optional) Use the People, Vehicle, and Date filters for more granular searches

7.Hovering over a thumbnail with the people or vehicle filters selected gives a count of the people/vehicles in the frame with an option to archive the clip. By hovering over the previews, you can see tracks for the individual.

8.Click the thumbnail to be taken to the exact time in the recorded footage.

Note: People and/or vehicles will only be available if these objects were detected in the camera frame.

View people trajectories (paths)

The people trajectories feature visualizes the paths of people moving through the scene to show the trajectories of each detected person.

Trajectories drastically improve the motion event recall and enable the cameras to recognize people and vehicles at a further distance. For a detailed breakdown of the detection ranges of each model, see the People Analytics Guide.

1.In Verkada Command, go to All Products > Cameras.

2.Select a camera to view its feed.

3.At the top, click Motion.

4.(Optional) Make a selection on the video player grid to search for motion in the area.

5.Select the People or Vehicle filter to see the trajectories.

Compatible cameras

The following table outlines which camera models support Motion Events, which models support Motion Trajectories, and where the motion model is running. Newer camera models have the capability to run the motion detection model on the camera, whereas D-series cameras still rely on the Verkada Cloud to run the model.

People and Vehicle History Search

People and Vehicle History Search

Learn how to use the Search page to view all people and vehicles in your organization

Updated over a week ago

You can use the People and Vehicle search pages to:

Search for people

See also how to search for people using our mobile apps.

Search for People of Interest

Set People of Interest notifications

To receive alerts for People of Interest, you need to set up alert based on your events.

IMPORTANT

People of Interest replaced Profiles on June 8, 2023. Profiles created before this date that were not set as People of Interest are not automatically send People of Interest alerts.

To set up notifications when a particular face is detected:

Create People of Interest

You can manually create a People of Interest group by uploading an image of a person’s face.

Merge People of Interest

Sometimes duplicate People of Interest are accidentally created. If this happens, you can merge the duplicate People of Interest profiles.

Create a new tag to People of Interest

You can create and add tags to People of Interest to group similar profiles together.

Type the desired name and at the bottom of the tag list, click Add Tags.

Add a tag to a user’s profile

Select the profile and select the plus (+) icon (adjacent to the Tags button). If the tag you want to add is already in the list, you can select it from the list.

Filter a tag name

Remove a person of interest

.

Search for vehicles

Search all license plates

If you have Verkada License Plate Recognition (LPR) cameras installed, you can use the All License Plates and License Plates of Interest tabs.

Enable Occupancy Trends

The Occupancy Trends feature provides organizations with an estimate of the foot traffic at critical locations within their facilities. These estimates can provide valuable insights for optimizing staffing, adjusting hours of operation, and or tracking the

performance of marketing and promotional activities.

Note: This feature is available on the CB52, CB62, CM42, CD32, CD42, CD52, and CD62 models.

​

Installation guidelines

Required. To use this feature, People Analytics must be enabled. To do so, follow the steps in the People Analytics guide.

For best performance, we recommend these installation guidelines during the installation of a camera where Occupancy Trends will be enabled:

1.In Verkada Command, go to All Products > Cameras.

2.Select a camera and go to the camera’s Settings page.

3.Scroll down to the Analytics section and toggle on Occupancy Trends.

4.Return to the camera’s main page and select the Analytics tab (displayed below the camera’s live feed).

5.Click Add lines to open the wizard.

6.Click and drag the camera view to draw a line across the screen. You can draw multiple lines, though data from all lines are aggregated.

7.Click one of the dropdown menus (displayed near the arrow heads) to change how users crossing in that direction are counted. The Ignore option indicates that users crossing this direction are not counted by the Occupancy Trends feature.

8.After you set up the lines for the camera’s view, click Save.

View Occupancy Trend estimates

Export Occupancy Trends results

You can export Occupancy Trends results as a .csv file.

1.Go to the Analytics tab.

2.At the top right, click Downloadto automatically download your occupancy trends results.

View Live Motion on Floor Plans

View Live Motion on Floor Plans

Learn how you can view live motion on your floor plan in real-time

Updated over a week ago

Verkada’s motion display feature offers two ways to see live motion on your site’s floor plans in real-time.

Set up motion detection

With motion detection, the camera’s field of view pulses when motion is seen. This happens in real-time.

1.In Verkada Command, go to All Products > Floorplans.

2.Select the building and floor plan you want to monitor.

3.On Floorplans, at the bottom right, click Motion Detection.

Example: Selected Floor Plan

Detect People Count

Detect People Count

Learn how to detect the number of people in your camera frame

Updated over a week ago

When you scrub through a Verkada camera’s historical video clips:

.

.

Alibi Vigilant

High-Performance Solutions
for any Security Challenge

Alibi solutions are designed – based on dealer feedback – to deliver the best possible user experience from installation to operations. Alibi Vigilant gear delivers high-resolution video security – from 2MP to 8MP – and flexible channel counts – 4CH to 128CH – to handle projects of all sizes. Alibi Vigilant gear is built with the latest features including Starlight chipsets, powerful video analytics, advanced compression, power-over-ethernet and more. Nearly every Alibi Vigilant product is NDAA compliant and are approved for use on federally-funded projects.

Alibi Hybrid Cloud

COMING SOON

Alibi Hybrid Cloud provides advance system health monitoring capabilities to proactively alert you when your system is not working properly. Additionally, cutting-edge Gun Detection analytics can be enabled to identify and alert if firearms are brandished in the field of view. AI-based analytics helps reduce false alarms by up to 95%.
Our solutions specialists will be on-site to answer any questions.

Powered by Actuate

Alibi Security Firmware and Manuals 2024

.

.

How to check your Alibi Witness firmware version

The firmware version that has been loaded on your recorder is noted on the large yellow sticker on the outside of your recorder box. You need to compare this version with the latest firmware available on-line by following these instructions.

Download the Alibi Firmware Upgrade Instructions for detailed information.

All available software and firmware downloads can be found on the Alibi Downloads Page.

Tirade WIP Series Firmware Update

As of May 2015, all Tirade WIP series wireless access points feature an updated firmware version, enhancing both performance and stability.

The latest version of Tirade firmware features an upgrade from iPoll to a proprietary iPoll2 transmission mode. iPoll2 transmission mode uses a centralized control scheme and ensures smooth packet transmission of voice, video, and data, and features a smarter polling method than iPoll—polling data more often.

If you have previously purchased Tirade WIP series wireless access points and are adding new units to expand your wireless security solution—please make sure that the firmware matches. Because iPoll2 is a proprietary format, all integrated Tirade WIP devices need to be running the latest version of firmware—to ensure seamless communication between devices.

Below are the Tirade firmware upgrade release notes, along with a link to firmware updating instructions.

NOTE: Before you begin any firmware updates, please read the entire set of instructions for updating the firmware.

Are You Running the Latest Tirade Firmware?

To ensure seamless communication between all Tirade devices, please verify that you’re using the latest (and most secure) firmware, we provide the following resources:

NOTE: NOTE: Upgrading to the latest version of firmware will also allow you to take advantage of new features and functionality that has been added to the software since you purchased or last upgraded your product.

.

Alibi Vigilant IP Camera Firmware

Looking for firmware? Find the latest firmware downloads, release notes and firmware instructions for current and discontinued Alibi Vigilant IP cameras in the following table.

IMPORTANT – Alibi Vigilant IP Camera Firmware Update:

We have released a new version of firmware for Alibi Vigilant IP cameras that fixes the ability to reset passwords for IP cameras. If you want to enable this functionality on installed Vigilant IP cameras, we recommend you click the following link to find complete directions to download the new software to upgrade your IP cameras.

Alibi Vigilant IP Camera Firmware Installation Instructions

Alibi Vigilant IP Camera Control 4 Connection Driver

If you have further questions, please contact Technical Support for assistance at 888.858.1442.

IPC_D1202 Firmware for the following camera models.

ALI-FB20-W, ALI-FB20, ALI-FB20-Z
ALI-FB40-W, ALI-FB40, ALI-FB40-Z
ALI-FD20-V, ALI-FD20-VZ
ALI-FD40-V, ALI-FD40-VZ
ALI-FT20
ALI-FT40

.

IPC-G6107 Firmware for the following camera models.

ALI-FB80
ALI-PD40-VZA
ALI-FD80-V
ALI-PT40-ZA
ALI-FT80
ALI-PB40-ZA
ALI-PB40-A
ALI-PD40-VA
ALI-PT40-A
ALI-PM40-A

.

DIPC-B1209 Firmware for the following camera models.

ALI-FB20-U
ALI-FD20-VU
ALI-FT20-U

.

DIPC-B1226 Firmware for the following camera models.

ALI-FB20-AW
ALI-FD20-VAW

.

DIPC-B1211 Firmware for the following camera models.

ALI-FB40-U

.

GIPC-B6102 Firmware for the following camera models.

ALI-PS40-A
ALI-PT40

.

GIPC-B6106 Firmware for the following camera models.

ALI-PF50-A
ALI-PB80
ALI-PT80
ALI-PZ50-ZA

.

CIPC-B2302 Firmware for the following camera model.

ALI-PZ51-UZA

ALI-PZ20-LUZAI

.

QIPC-B1203 Firmware for the following camera models.

ALI-XB80-ZA
ALI-XD80-VZA
ALI-XT80-ZA
ALI-XF120-A

.

QIPC-B6209 Firmware for the following camera models.

ALI-XF120-VAI

.

QIPC-B6501 Firmware for the following camera models.

ALI-XF160-UA

.

QIPC-B2202 Firmware for the following camera models.

ALI-PZ21-UZA
ALI-PZ40-VUZAI
ALI-PB40-VUZAIE
ALI-PB80-VUZAIE

.

CIPC-B2302 Firmware for the following camera models.

ALI-PZ20-ZA

.

CIPC-B2302 Firmware for the following camera models.

ALI-PZ20-LZA

.

CIPC-B2302 Firmware for the following camera models.

ALI-PZ20-LUZAI

.

QIPC-B8701 Firmware for the following camera models.

ALI-XF80-LA

.

DIPC-B1216 Firmware for the following camera models.

ALI-FB21-A
ALI-FB21-Z
ALI-FD21-V
ALI-FT21-A

.

GIPC-B6202 Firmware for the following camera models.

ALI-FB21-UAI, ALI-FB41-UA, ALI-FB41-UZA
ALI-FD21-VUAI, ALI-FD41-UVZ, ALI-FD41-VU
ALI-FT21-UAI, ALI-FT40-UZA, ALI-FT41-UA
ALI-PB40-UAI, ALI-PB40-UAIE, ALI-PB40-UAIS, ALI-PB40-UZAI, ALI-PB40-VLUAI, ALI-PB40-VLUZAI
ALI-PB50-UAI, ALI-PB50-UZAI, ALI-PB50-VLUAI
ALI-PD40-VUAI, ALI-PD40-VUZAI, ALI-PD41-VUZAI
ALI-PD50-VUAI, ALI-PD50-VUZAI
ALI-PM41-VAI, ALI-PM40-UAI
ALI-PT40-UAI, ALI-PT40-UAIS, ALI-PT40-UZAI, ALI-PT40-VLUAI, ALI-PT40-VLUZAI
ALI-PT50-LUAI, ALI-PT50-UAI, ALI-PT50-UZAI
ALI-PZ50-LUZAIS

.

GIPC-B6202 Firmware for the following camera models.

ALI-PB60-UA
ALI-PD60-VUA
ALI-PT60-UA
ALI-PB60-VUZA
ALI-PD60-VUZA
ALI-PT60-VUZA
ALI-PB60-UAB
ALI-PD60-VUAB
ALI-PT60-UAB

.

GIPC-B6203 Firmware for the following camera models.

ALI-FB81-UA
ALI-FD81-VUA
ALI-FT81-UA
ALI-PF51-VA
ALI-PT50-VUAIF
ALI-PB50-UAIF
ALI-PB81-AI
ALI-PD81-AI
ALI-PT81-AI
ALI-PB80-VLUAI
ALI-PT80-VLUAI
ALI-XB81-UZAI
ALI-XD81-VUZAI
ALI-XT81-UZAI

.

GIPC-B6208 Firmware for the following camera model.

ALI-PF40-LUA

.

ANPR-B1103 Firmware for the following camera model.

ALI-XB20-VUZAI-ANPR

Alibi Vigilant Network Video Recorder Firmware

Looking for firmware? Find the latest firmware downloads, release notes and firmware instructions for current and discontinued Alibi Vigilant Recorders in the following table.

NVR-B3111 Firmware for the following Alibi Vigilant recorder models.

ALI-NR320P-8
ALI-NR640P-16

.

NVR-B3601 Firmware for the following Alibi Vigilant recorder models.

ALI-NR040F-1
ALI-NR080F-1
ALI-NR160F-2
ALI-NR160P-4
ALI-NR320P-4

.

NVR-B3613 Firmware for the following Alibi Vigilant recorder models.

ALI-NR041F-1
ALI-NR082F-2
ALI-NR162F-2
ALI-NR162P-4
ALI-NR322P-4
ALI-NR322P-8
ALI-NR641P-8

.

NVR-B3112 Firmware for the following Alibi Vigilant recorder models.

ALI-NR081F-2
ALI-NR161F-2
ALI-NR161P-4
ALI-NR321P-4

.

NVR-B5301 Firmware for the following Alibi Vigilant recorder models.

ALI-NR321P-8
ALI-NR640P-8

.

NVR-B5101 Firmware for the following Alibi Vigilant recorder models.

ALI-NR1280X-16

.

B3506 Firmware for the following Alibi Vigilant recorder models.

ALI-HR161F-2

.

B3502 Firmware for the following Alibi Vigilant recorder models.

ALI-HR160F-1

.

B3503 Firmware for the following Alibi Vigilant recorder models.

ALI-HR040F-1

.

B3519 Firmware for the following Alibi Vigilant recorder models.

ALI-HR042F-1

.

B3503 Firmware for the following Alibi Vigilant recorder models.

ALI-HR080F-1

.

B3516 Firmware for the following Alibi Vigilant recorder model.

ALI-HR081F-1

.

B3520 Firmware for the following Alibi Vigilant recorder models.

ALI-HR082F-1

.

B3511 Firmware for the following Alibi Vigilant recorder models.

ALI-HR162F-1

.

B3507 Firmware for the following Alibi Vigilant recorder models.

ALI-HR162F-2

B3518 Firmware for the following Alibi Vigilant recorder models.

ALI-HR163F-1

Alibi Witness Recorder Firmware and Manuals

Find the latest software for Alibi security video recorders including ACMS, firmware, power tools, Witness App and Mac and PC component downloads along with release notes and installation manuals.

ACMS Software for Alibi Recorders

Find the latest downloads for Alibi Central Management Software and installation manuals.

Alibi Witness Mobile App

Check out our page for the most current information on the Alibi Witness Mobile App.

Windows Codec Pack

colgroup>

Mac Web Components

colgroup>

Alibi Power Tools

colgroup>

Alibi 3004 Digital Video Recorder

Includes SKUs – ALI-DVR3004H, ALI-DVR3008H, ALI-DVR3016H

colgroup>

Alibi 1004 Digital Video Recorder

Includes SKUs – ALI-DVR1004E

colgroup>

Alibi Hybrid Series Video Recorder

Includes SKUs – ALI-HVR3004H, ALI-HVR3008H, ALI-HVR3016H, ALI-HVR5016H, ALI-TVR7032H

colgroup>

Alibi 3000 Series Network Video Recorders

Includes SKUs – ALI-NVR3004P, ALI-NVR3008P

colgroup>

Alibi 3100 Series Network Video Recorders

Includes SKUs – ALI-NVR3104P, ALI-NVR3108P

colgroup>

Alibi 3304 Network Video Recorders

Includes SKUs – ALI-NVR3304P

colgroup>

Alibi 3308, 3316 Network Video Recorders

Includes SKUs – ALI-NVR3308P, ALI-NVR3316P

colgroup>